Kraus KBU22KPF1612KSD30SS, KHU10030KPF1612KSD30SS, KHF20030KPF1612KSD30CH, KHF20033KPF1612KSD30SS, KHF20333KPF1612KSD30SS Installation Manual
...Page 1
INSTALLATION MANUAL
Single Lever Pull-Out
Kitchen Faucet
KPF-1612
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 16, 2016
Page 2
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service
1
Page 3
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
PRIOR TO INSTALLATION
• Make sure you have all necessary parts by checking the diagram and parts
list. If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the
old faucet to release any built up pressure. Remove existing faucet. Clean
sink or countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8”
• Max countertop thickness without deck plate: 1-3/8”
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or Customerservice@kraususa.com
Tools Required
Adjustable Wrench
Phillips Screwdriver
Safety Goggles
Bucket
Silicone Sealant
2
Page 4
Diagram and Parts List
Included Parts:
1. Faucet Body
2. Base O-Ring
3. Rubber Washer
4. Metal Washer
5. Fixing Nut
6. Fixing Screw (2)
7. Weight
8. Spray Head
9. Spray Hose
10. Spring
11. Spring Holder
12. Hot and Cold Waterlines (2)
13. Supply Hose
KPF-1612 Diagram and Parts List
Hot
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
8 15/32”
15
15
Wrench Phillips Screwdriver
Tools you will need:
9
F
8
E
1
A
7
D
A. Faucet Body
B. Base
C. Mounting Hardware Assembly
C1 Rubber Washer
C2 Metal Washer
C3 Mounting Nut
C4 Mounting Screws
3
10
G
11
H
12
I
J
13
B
2
3
C1
4
C2
5
C3
6
C4
D. Weight
E. Spray Head
F. Spray Hose
G. Spring
H. Sprayer Holder
I. Hot and Cold Waterlines
J. Supply Hose
Page 5
Faucet Dimensions
8”
203mm
8-1/2”
215mm
Hot
Water
Ø1-3/8”~Ø1-1/2”
Ø35mm~Ø38mm
Cold
Water
4
Page 6
Faucet Dimensions
Installation Method 1
Installation Method 2
The minimum distance between
the faucet hole and the wall should
be 3.5”
If the distance between the faucet
hole and the wall is less than 3.5”,
position the faucet lever 30 degrees
to 90 degrees o of the wall to
allow for full operation
Faucet Installation Procedure
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Minimum distance 3.5”
Less than 3.5”
30˚
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
9
8
11
12
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Less than 3.5”
30˚
Ø35~Ø38
1
2
3
4
5
6
Ø1 3/8~Ø1 1/2”
90˚
25˚
O
Left
Hot Water
On
21-1/4”
540mm
5
Max1-3/8”
Max35mm
Page 7
Faucet Installation Procedure
1
2
13
10
3
4
5
6
7
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Less than 3.5”
30˚
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
9
8
11
12
Max35
Max 1 3/8”
Hot
Water
Cold
Water
Ø35~Ø38
Ø1 3/8~Ø1 1/2”
540
21 1/4”
8 15/32”
Ø35~Ø38
1
2
3
4
5
6
Ø1 3/8~Ø1 1/2”
90˚
25˚
O
Left
Hot Water
On
Installation Method 1
Minimum distance 3.5”
Installation Method 2
Less than 3.5”
The minimum distance between
the faucet hole and the wall should
be 3.5”
If the distance between the faucet
hole and the wall is less than 3.5”,
position the faucet lever 30 degrees
to 90 degrees o of the wall to
allow for full operation
30˚
6
Page 8
Step 3
Step 4
After adjusting the direction of
the faucet body (1), tighten the
mounting nut (5) until snug and
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
Connect the spray hose (9) to
the supply line and tighten with
a wrench until snug, then install
the weight (7) at the lowest point
(horizontally) on the spray hose
(12)
Hot
Water
5
7
7
J
F
Step 1
540
21 1/4”
1
2
3
4
5
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
5
6
7
90˚
Left
Hot Water
Right
Cold Water
Ø1 3/8~Ø1 1/2”
Step 2
Ø35~Ø38
Remove mounting screws (6),
Remove mounting hardware
assembly (C)
mounting nut (5), metal washer
(4), and rubber washer (3) from
the faucet body (1)
1
A
2
3
C1
4
C2
C3
5
C4
6
Insert faucet body (A) into hole
Insert the faucet body (1) into
on deck or sink with base (B)
the hole on the deck with the
attached. Attach mounting
base o-ring (2). Install the rubber
hardware assembly (C)
1
A
2
B
washer (3), metal washer (4),
mounting nut (5) and mounting
screws (6) from underneath the
sink
3
C1
C2
4
C3
5
C4
6
7
Page 9
Step 3
Hot
Water
7
Hot
Water
1
2
3
4
5
5
6
7
Hot
Water
7
Step 4
After adjusting the direction of
Adjust faucet body. Secure
mounting hardware (C) with
the faucet body (1), tighten the
wrench and Phillips head
mounting nut (5) until snug and
screwdriver
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
5
C
Connect spray hose (F) to supply
Connect the spray hose (9) to
hose (J) and tighten. Attach
the supply line and tighten with
weight (D) to lowest point
a wrench until snug, then install
vertically on spray hose (F)
the weight (7) at the lowest point
(horizontally) on the spray hose
(12)
J
D
7
F
8
Page 10
Step 5
Usage
How to Operate the Handle
1. Pull the lever to the right to
turn on the water. Push to the
left to turn o
2. Pull the lever forward
to increase hot water ow
and push the lever back to
increase the cold water ow
90˚
25˚
O
Left
Hot Water
Right
Cold Water
On
90˚
Left
Hot Water
Right
Cold Water
Hot
Water
Cold
Water
Connect and tighten waterlines (I) to angle stops. Turn on the angle stops
Connect hot and cold waterlines (12) to the angle stops and tighten with
a wrench until snug, then unscrew spray head (8), hold the tip of the spray
and check for leaks (DO NOT TURN FAUCET ON)
hose (9) and turn on the faucet to ush any debris
Installer Tip
Remove spray head (E) and turn
faucet on for 60 second to flush
any debris
9
Page 11
Usage
90˚
Left
Hot Water
Right
Cold Water
How to Operate the Handle
25˚
1. Pull the lever to the right to
turn on the water. Push to the
left to turn o
90˚
Left
Hot Water
O
On
Right
Cold Water
2. Pull the lever forward
to increase hot water ow
and push the lever back to
increase the cold water ow
10
Page 12
Replacement Parts
5
2
1
23
26a
26b
25
24
22
1. Spray Head
2. Plastic Sleeve
3. Sprayer Holder
4. Spring
5. Spring End Cap
4
6
3
6. Set Screw
7. Cap
8. Set Screw
9. Lever
10. Set Screw
11. Handle
12. Cartridge Cover
13. Locking Nut
14. Cartridge
14
7
8
13
12
9
10
11
15. Protective Sleeve
16. Base
17. Base O-Ring
18. Rubber Washer
19. Metal Washer
15
16
17
18
19
20
21
20. Mounting Nut
21. Mounting Screw
22. Hose
23. Washer
24. Weight
25. Supply Hose
26. Hot & Cold Waterlines
11
Page 13
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the
handle (11)
Water will not shut off
completely
Locking nut (13) has
come loose
Cartridge (14) may be
defective
Unscrew the lever (9)
on the handle (11) by
hand. Loosen set screw
(10) with a hex wrench
(2.5 mm). Remove
the handle (11) and
unscrew cartridge
cover (12) by hand.
Tighten locking nut
(13) with an adjustable
wrench
Unscrew the lever (9)
on the handle (11)
by hand. Loosen set
screw (10) with a hex
wrench (2.5 mm).
Remove the handle
(11) and unscrew
cartridge cover (12)
by hand. Unscrew the
locking nut (13) with
an adjustable wrench.
Remove ceramic disc
cartridge (14). Check
for cracks
Leaking between spray
head (1) and the hose
(22)
Spray head (1) may be
loose or washer (23) is
not seated correctly in
the hose connection
Tighten the spray head
(1) by hand until snug.
Make sure the washer
(23) is seated correctly
12
Page 14
Codes/Standards Applicable:
GREEN
NSF/ANSI Standard 61 certied by IAPMO
NSF/ANSI Standard 372 certied by IAPMO
Water Eciency
LEAD FREE
I
A
P
M
O
R
&
T
TM
Meets ASME A112.18.1M/A112.18.1
1.75gpm 6.6L/min maximum
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
13
Page 15
Care & Maintenance
Hot
Water
Cold
Water
Push
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
www.kraususa.com
14
Page 16
REGISTER YOUR PRODUCT TODAY
Receive Proof of Ownership
Access Customer Care & Installation Help
Get Exclusive Kraus Oers & Promotions
Scan to Register Online
or visit http://www.kraususa.com/registration
We’re always looking for ways to improve.
Please take a moment to share your experience.
Visit http://www.kraususa.com/review to let us know what you think
about your new Kraus product.
Contact Us to Learn More
1.800.775.0703 / www.kraususa.com / customerservice@kraususa.com
Like & Follow KrausUSA
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
www.kraususa.com
Loading...