Page 1
INSTALLATION GUIDE
Arlo™ Single Lever Basin Faucet
KBF-1201
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. Dec 2, 2017
Page 2
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
DO NOT RETURN TO STORE
Please contact our Customer Service Team
1-800-775-0703 / customerservice@kraususa.com
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
1
Page 3
Prior to Installation:
Make sure you have all necessary parts by checking the diagram and parts list. If
•
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
Turn o the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure
• Pre-drilled countertop hole size requirement: 1-3/8” (min)
• Max countertop thickness: 2-1/2”
2
Page 4
Diagram and Parts List
J
I
A
D
E
F
B
G
C
H
A. Faucet Body
B. Waterlines
C. Flange
D. Aerator
3
E. Aerator Key
F. Hex Wrench
G. Washer
H. Lock Nut
I. Deckplate
J. Drain
Page 5
Faucet Dimension
6 1/4”
[159mm]
2 1/2in
[64mm]
2-9/16-24UNEF-2B
8”
[203mm]
6 3/4”
[172mm]
5”
[126mm]
4”
[100mm]
2 1/4”
[57mm]
6 5/8”
[169mm]
5”
[126mm]
8”
[203mm]
4”
[100mm]
2 1/2in
[64mm]
2-9/16-24UNEF-2B
Installer Tip:
Shut o main water supply before installing new faucet
4
Page 6
Step 1: Remove washer and lock nut
a.
A
G
H
b.
Shut o the water supply. Remove the
old faucet. Clean the mounting surface.
A
C
WITH FLANGE: Remove the washer (G)
and lock nut (H) from the faucet (A) as
shown in gure a.
WITH DECK PLATE: Remove the washer
(G), the ange (C )and lock nut (H) from
the faucet (A) as shown in gure b.
G
H
Step 2.1: Install faucet (with deck plate)
Align the hole in the deck plate (I) with
A
I
G
the mounting hole in the sink. Place the
faucet (A) through the deck plate (I) and
mounting hole in the sink until the
faucet (A) sets on top of deck plate (I).
Secure the faucet (A) to the sink using
the washer (G) and lock nut (H) provided.
Ensure the washer (G) and hoses (B)
are no interference.
H
B
G
H
5
Page 7
Step 2.2: Install faucet (with ange)
A
C
G
H
B
G
H
Before installation, ensure that the
ange (C) is placed on the bottom
of the faucet (A). Place the faucet (A)
through the mounting holes in the
sink until the faucet (A) sets on top
of the sink. Secure the faucet (A) to the
sink using the washer (G) and lock nut (H)
provided. Ensure the washer (G) and
hoses (B) are no interference.
Step 3: Connect waterlines to main valve
Attach waterlines(B) to angle stops
and tighten until snug. Turn on angles
stops and check for leaks (DO NOT TURN
FAUCET ON)
B
6
Page 8
Step 4: Install drain
1
2
3
4
5
Remove the waste stopper (1) and drain
ange (2) from the drain body (5). Screw
the nut (4) all the way down, and push
the concave washer (3) down.
Apply silicone sealant (not included)
SILI
1
2
3
a
under the drain ange(1) and place the
drain ange (1)into the drain hole of
the sink. From underneath the sink,
screw the drain body (4) onto the drain
ange (1). Ensure that the opening (a) for
the ball rod on the drain body (4) faces
towards the rear of the sink. Tighten the
concave washer (2) and nut (3) on the
drain body (4). Do not overtighten.
4
7
Page 9
Step 4: Install drain
Insert 2
Insert 1
hole in the sink. Remove the strap (6) and
clip (5) from the ball rod (3).
Insert the waste stopper (1) into the drain
6
Remove the ball nut (4). Insert the ball
rod (3) into the drain body (2) and through
1
3
A
the hole of the stopper (1). See Insert 1.
For easier removal and cleaning, rotate
the stopper (1) 90 degrees so that the
ball rod (3) does not go through the hole
4
B
2
in the stopper (1).See Insert 2.
Secure the ball nut (4) against the hole in
2
C
2
5
the drain body (2) and tighten the ball nut
(4) onto the threaded end. Do not
overtighten.
Insert the lift rod (2) through the faucet
1
2
(1) and down into the strap (3).Tighten
the thumb screw (4).
3
4
8
Page 10
Step 4: Install drain
3
Attach the ball rod (1) to the strap (3)
using the clip (2).
2
1
Loosen the thumb screw (3) on the
strap (2). Push down on the lift rod
(1) until the stopper is in the open
position. Retighten the thumb
1
2
3
screw (3).
Step 5: Flush faucet
D
E
9
After installing faucet, remove
aerator (D) with included aerator
key (E). Turn water on for 30
seconds to remove any debris.
Reassemble aerator (D).
Page 11
Diagram and Parts List
23
3
4
5
6
7
8
9
15
16
17
10
11
1
2
14
13
24
25
26
27
28
29
12
18
19
20
21
22
10
Page 12
13
Diagram and Parts List
1. Index
2. Set Screw
3. Handle
4. Screw
5. Cap
6. Bonnet Nut
7. Cartridge
8. Aerator
9. Aerator Wrench
10. Flange
11. Washer
12. Lock Nut
13. Deck plate & Gasket
14. Hex Wrench
15. Lift Rod Knob & Lift Rod
16. Thumb Screw
17. Strap
18. Clip
19. Ball Nut
20. Ball Washer
21. Ball Rod
22. Ball Washer
23. Waste Stopper
24. Drain Flange
25. Rubber Washer
26.
Concave Washer
27. Metal Washer
28. Nut
29. Drain Body
Tools you will need:
Adjustable Wrench
Silicone Sealant
(optional)
Phillips Screwdriver
Safety Goggles
11
Pipe Tape
Page 13
Trouble - Shooting
Hot
Water
Cold
Water
Push
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM C A U S E A C T I O N
Leakage under the
handle
Aerator drips or has
inconsistent water ow
pattern
Water will not shut o
completely
There is leaking from the
sink drain at the base of
the sink.
Bonnet nut (6) has
come loose
Aerator (8) is dirty or
not seated properly
Cartridge may need to
be adjusted or replaced
The sink has a rough or
irregular surface.
Remove the index (1).
Loosen set screw (2) with
hex wrench (14). Remove
the handle (3). Unscrew
cap (5) (by hand only).
Tighten bonnet nut
(6) with an adjustable
wrench
Unscrew aerator (8)
with aerator wrench (9)
and clean out debris
Remove the index (1).
Loosen set screw (2) with
hex wrench (14). Remove
the handle (3). Unscrew
cap (5) (by hand only).
Tighten bonnet nut
(6) with an adjustable
wrench. Remove the
cartridge (7). Check for
cracks
Apply additional silicone
sealant to the beveled
side of the drain ange.
Retighten and test for
leaks
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
12
Page 14
Codes/Standards Applicable:
NSF/ANSI 372
GREEN
LEAD FREE
I
A
P
M
O
R
&
NSF/AN SI 61
T
TM
ASME A112.18.1
1.2GPM 4.5L/min maximum
Faucet Warranty
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”).
Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original
location. The warranty is non-transferable.
Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under
normal usage for the lifetime of the product. The warranty commences from the initial date of purchase by the
owner or trade professional, from an authorized Kraus dealer, through the lifetime of the original owner or
end-user.
Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine,
aerators , structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel, etc) of the product to be free from defects in material and workmanship
under normal usage for a period of one (1) year. The warranty commences from the initial date of purchase by the
owner or trade professional, from an authorized Kraus dealer, through the one (1) year term of the original owner
or end-user.
Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and
workmanship under normal usage for a period of five (5) years. The warranty commences from the initial date of
purchase by the owner or trade professional, from an authorized Kraus dealer, through the five (5) year term of
the original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be
repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original
owner or end-user, and is not transferable to a subsequent owner.
Restrictions
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased
at discount outlets, unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness,
accident, hard water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by
improper maintenance, alteration of the product, or failure to follow care or installation instructions enclosed with
your product. Avoid using abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using
abrasive pads, steel wool, or wire brushes, as these will damage and wear down the finish.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions
supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.
This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade
professional. Kraus insists that such professionals have experience in the installation of bathroom and kitchen
manufactured goods.
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty
does not allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or
other consequential damages, and Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
13
Page 15
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of
merchantability and fitness for a particular purpose, or compliance with any code.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and
Puerto Rico shipping charges may apply). International shipping fees are not included.
Commercial Warranty
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial,
and business use.
All incidental or consequential damages are specifically excluded. No additional warranties, express or implied,
are given, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional please contact a Kraus
Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
14
Page 16
IMPORTANT
Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
www.kraususa.com
Loading...