INSTALLATION MANUAL
Sheven Single Lever Vessel Faucet
FVS-1002
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Congratulations on your new Kraus purchase!
We would like to take this opportunity to thank you for your business with Kraus USA.
It is our sincere hope that you are completely satised with your Kraus experience.
We welcome any questions or comments you may have, and look forward to assisting
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com.
In order to allow us to serve you better, we recommend registering your new Kraus
product at: www.kraususa.com/product-registration
Sincerely,
Kraus Customer Service Department
Prior to Installation
Make sure that the cold and hot water lines are turned o
•
• Wrap all threaded connections with Teon tape. Always wrap in a clockwise
direction
• Cover your drain to avoid losing parts
• Do not disassemble the main faucet body, as it has been installed & commissioned
correctly & precisely before delivery from the factory
• To keep the faucet from jamming, ush the water pipe before installation
• Using condition: Working pressure at 0.05-1.0MPa (including cold & hot water
pressure) with applicable water temperature: 4C-90C
FVS-1002 Diagram and Parts List
8
9
Hot Water Cold Water
9
13
13
Included Parts:
1. Faucet Body
2. Base Trim Ring
3. Base O-Ring
4. Rubber Washer
5. Metal Washer
6. Mounting Nut
7. Mounting Screws (2)
8. Hot & Cold Waterlines (2)
9. Manual
1
2
3
4
5
6
8
Tools you will need:
7
9
Wrench Phillips
Screwdriver
Dimension Drawings
348
109 226
4 9/32” 8 7/8”
13 11/16”
Max x 35 Max
1 3/8”
Hot Water Cold Water
Safety Tips
•
If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat
• Protect your eyes with safety glasses when cutting or soldering
Dimension Drawings
348
13 11/16”
60 º
109 226
4 9/32” 8 7/8”
Ø33-Ø35
Ø1 5/6”~Ø1 3/8”
Max x 35 Max
1 3/8”
Safety Tips
•
Do not overtighten xing screws/nuts. Tighten nger-tight, then use a wrench/
screwdriver to tighten the xing screw/nut until snug
FVS-1002 Installation Procedures
Flush the
pipes
Do
not
Disassemble
Hot Water Cold Water
348
109 226
60 º
4 9/32” 8 7/8”
13 11/16”
Max x 35 Max
1 3/8”
Ø33-Ø35
Ø1 5/6”~Ø1 3/8”
Max x 35 Max
1 3/8”
Ø33-Ø35
Ø1 5/6”~Ø1 3/8”
Step 1
Step 2
Remove rubber washer (4),
metal washer (5), mounting nut
(6) and mounting screws (7).
Keep the base trim ring (2) and
base O-ring (3) on the base of
the faucet.
(Suggested)
Ø33~Ø35 hole
Ø1.29”~Ø1.37”
Screw and hand-tighten the
hot and cold waterlines (8)
into the faucet body (1), hot
side left & cold side right when
spout is facing up. Install the
faucet body (1) through the
1-3/8” predrilled hole in the
countertop. Attach the rubber
washer (4), metal washer
(5), mounting nut (6), and
mounting screws (7) from
underneath the sink.
Step 3
Step 4
After adjusting the direction
of the faucet body (1), tighten
the mounting nut (6) until snug
and then tighten the mounting
screws (7) to the nut with a
Phillips head screw driver until
snug.
Connect hot and cold waterlines
(8) to the angle stops and
tighten with a wrench. Unscrew
the aerator cover by hand, and
remove the aerator, then turn on
the water to remove any leftover
debris
Care & Maintenance
Hot
Water
Cold
Water
Push
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use a cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
Usage
How to operate the handle:
Raise the lever handle to turn on the
water. Push down to turn o.
Turn the lever handle to the left
to increase hot water ow and
temperature, turn to the right
to increase cold water ow and
temperature.
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not
work properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the
handle
Aerator drips or has
inconsistent water flow
pattern
Water will not shut off
completely
Adjusting locking nut
has come loose
Aerator is dirty or not
seated properly
Cartridge may be
defective
Remove handle index
button. Loosen set
screw with hex wrench.
Remove handle by
hand only. Tighten
locking nut with an
adjustable wrench
Unscrew aerator cap by
hand. Remove aerator
and clean out debris
Remove handle index
button. Loosen set
screw with hex wrench.
Remove handle by
hand only. Unscrew
trim cap by hand only.
Unscrew the locking
nut with an adjustable
wrench. Remove
ceramic disc cartridge.
Check for cracks
Codes/Standards Applicable:
Codes/Standards Applicable:
Specied model meets or exceeds the following: ANSI/ASME A112.18.1, cUPC,
Specied model meets or exceeds the following: ANSI/ASME A112.18.1, cUPC,
AB1953
AB1953
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards
by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not
transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship
error during the warranty period: Kraus will provide replacement parts at
no charge, or at its option, replace any product or part of the product that is
deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot
be made in timely fashion, Kraus may elect to refund the purchase price in
exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to
ensure proper function. We provide you with complete knowledge to perform
this maintenance and can also recommend resources if you are unable to fulfill
this service.
A. Kraus will not be responsible for product failures due to lack of maintenance
or proper use. Please read your care and maintenance documentation to determine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be
presented at the time of the warranty claim, without exception, for this warranty
to be applied to all Kraus products.
C. Kraus recommends installing all Kraus products with a licensed, professional
plumber. Kraus will not be held responsible for any damage or product failure
due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits
of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unau-
thorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NONAPPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable
for incidental, consequential or special damages associated with the return,
replacement, installation or use of your product. This includes freight costs,
cartridge replacement, labor, travel time, lost profit, home damages and other
contingent liabilities and costs (including, without limitation, costs associated
with experts, investigations, analyses, attorneys and other professionals and
services). The Kraus warranty is a comprehensive and explicit limit of liability,
and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local
building or plumbing codes. It is the consumer’s responsibility to determine
local code compliance. This warranty extends to the original purchaser and first
consumer.
HELP LINE
For additional assistance at any point in the installation process, please call us at
1.800.775.0703 or email us at info@kraususa.com
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com.
www.kraususa.com
Loading...