Page 1
INSTALLATION GUIDE
Artec Pro™ Single Handle Commercial
Kitchen Faucet
KPF-1603
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. Aug 21, 2018
Page 2
1
Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / customerservice@kraususa.com
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NO T RETURN TO STORE
1
Page 3
2
Prior to Installation:
•
Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
to release any built-up pressure
• Pre-drilled countertop hole size requirement: 1-3/8” (min)
• Max countertop thickness: 2”
Tools you will need:
13
Wrench Phillips Screwdriver
Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
Page 4
3
Diagram and Parts List
B4
B5
C
A
A. Faucet Body
B1. Seat
B2. Rubber Washer
B3. Metal Washer
B4. Mounting Nut
B5. Screw
C. 2.2 GPM Flow Restrictor
D. Hex Wrench
B1
B2
B3
D
Page 5
4
Faucet Dimension
Installer Tip:
4 1/8in
[106.5mm]
24 3/4in
[628.7mm]
2 3/8in
[60.0mm]
9/16-24UNEF-2B
7 1/8in
[182.6mm]
9 3/4in
[248.2mm]
6in
[153.2mm]
7 5/8in
[198.2mm]
6 5/8in
[173.3mm]
MAX:2 3/8in
[60.8mm]
Page 6
5
Step 1: Remove washer and lock nut
Insert faucet through hole in sink or
countertop.From underneath sink,
attach the seat (B1), rubber washer (B2),
metal washer (B3), and nut (B4). Lock
nut (B4) into position by tightening
screws (B5).
Shut o the water supply.
Remove the old faucet. Clean the
mounting surface. Remove mounting
hardware (B) from faucet body (A).
Step 2: Install faucet
B1
B2
B3
B4
B5
A
B
Page 7
Step 3: Making the water supply connections
Push the quick connector (2) rmly
upward andattach it to the receiving
block (1). Pull down moderately to
ensure the connection has been made.
If it is necessary to remove the quick
connector (2), squeeze the tabs on the
hose and then pull down to disconnect.
6
Step 4: Making the water supply connections
Thread the nut (1) on the supply line
onto the outlet of the water supply
valve and tighten with a wrench.
Do not overtighten.
1
1
2
Page 8
Step 5: Flushing and checking for leaks
Pull the hose assembly out of the spout
and remove the spray head by
unscrewing it from the hose in a
counterclockwise direction. Be sure to
hold the end of the hose down into the
sink and turn the faucet on to the warm
position where it mixes hot and cold
water.
Flush the water lines for one minute. This
ushes away any debris that could cause
damage to internal parts. Check for leaks.
Reinstall the spray head by hand
tightening it back onto the spray hose.
7
NOTE:
1.Do not lose the rubber washer (1) when
installing back the sprayer
2.The magnet end marking with black dot
should be toward the hose for correct
magnet installation
1
2
Page 9
This faucet ships with a 1.8 GPM ow
restrictor installed. An optional 2.2 GPM
ow restrictor is also included in the box.
To switch the ow rate of the faucet:
1. Disassemble the quick connect assembly
by separating the connector (1) and quick
connect (2).
2. Replace 1.8 GPM connector (blue) with
the 2.2 GPM connector.
3. Reinstall the quick connect assembly.
Step 7: Flow Regulator Replacement
8
2
1
2
1
1
To activate the spray mode, simply
press the handle (1) located under
the spray head.
1
Step 6: Flush faucet
NOTE: In compliance with CEC standards, this faucet is designed with a 1.8 gpm
ow rate. At your discretion, you may modify the product with the included 2.2
gpm restrictor. Please note that doing so will remove the capability of this product
to meet specic low-ow standards. Kraus is not liable for any alterations made to
the product post-sale, and highly advises that you consult with your local or
statewide plumbing enforcement agency prior to any modication.
Page 10
Replacement Parts
1. Spray head
Replacement Parts List Part NO
2. Magnet
3. Spray hose assembly
4. Spring
5. Inverter
6. Spray support assembly
7. Spout nut
8. Spout
9. Diverter
10. Aerator assembly
11. Cartridge
12. Bonnet nut
13. Cap
14. Handle assembly
15. Rubber & metal washer
16. Mounting nut & nut
17. Block
18. Flange
19. Seat
20. 2.2GPM ow restrictor
21. 1.8GPM ow restrictor
22. Quick connect
23. Hex wrench
CH, SFS, SFSMB
Finish
BLBG, BLSFS,
GRCH, GRSFS*
CH, SFS, BG
CH, SFS, BG
CH, SFS, BG, MB
CH, SFS, BG, MB
CH, SFS, BG, MB
CH, SFS, BG
CH, SFS, BG
CH, SFS, BG
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14.2
14.3
14.1
17
21
20
23
22
18
16
15
19
KP27063
KP27080
KP27064
KP27065
KP27066
KP27067
KP27068
KP27069
KP27070
KP27071
KP27072
KP27028
KP27079
KP27073
KP27077
KP27078
KP27075
KP27074
KP27076
KP27020
KP27060
KP27061
KP27062
*Spray hose assembly color options: Black hose w/ Brushed Gold connector (BLBG), Black
hose with Spot-Free Stainless connector (BLSFS), Gray hose with Chrome connector (GRCH),
Gray hose with Spot-Free Stainless connector (GRSFS)
Page 11
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLE M C A U S E A C T I O N
Leakage under the
handle
Bonnet nut (12) has
come loose
Remove the index (14.3).
Loosen set screw (14.2) with
hex wrench (14). Remove
the handle (14.1). Unscrew
cap (13) (by hand only).
Tighten bonnet nut
(12) with an adjustable
wrench
The aerator has an
irregular or reduced
water ow
The aerator is dirty or
mis-tted
Remove the aerator and
check for debris.
Ensure that the rubber
washer is properly
installed.
The water pressure
is low.
The connector
underneath the deck is
clogged with debris
The aerator is clogged
Turn o the water supply
and disconnect the
connector / aerator.
Unscrew the connector /
aerator and clean under
running water.
Screw the connector /
aerator back.
Test water ow. If water
pressure is still low then
replace the connnector /
aerator.
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
Hot
Water
Cold
Water
Push
10
Page 12
Codes/Standards Applicable:
NSF/ANSI 372 NSF/ANSI 61-9
ASME A112.18.1
1.8GPM 6.8L/min maximum
11
Faucet Warranty
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”).
Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location.
The warranty is non-transferable.
normal usage for the lifetime of the product. The warranty commences from the initial date of purchase by the owner or
trade professional, from an authorized Kraus dealer, through the lifetime of the original owner or end-user.
Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators ,
and stainless steel, etc) of the product to be free from defects in material and workmanship under normal usage for a
period of one (1) year. The warranty commences from the initial date of purchase by the owner or trade professional,
from an authorized Kraus dealer, through the one (1) year term of the original owner or end-user.
Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and
original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be
repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or
end-user, and is not transferable to a subsequent owner.
Restrictions
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at
discount outlets, unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard
water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance,
alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using
abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire
This warranty does not apply to Products that have not been installed or operated in accordance with instructions
supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.
This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional.
Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods.
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does
not allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other
consequential damages, and Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of
Page 13
Rico shipping charges may apply). International shipping fees are not included.
Commercial Warranty
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
legal rights, and you may also have other rights which vary from state to state.
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional please contact a Kraus
Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor P
ark Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
12
Rico shipping charges may apply). International shipping fees are not included.
Commercial Warranty
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
legal rights, and you may also have other rights which vary from state to state.
Page 14
IMPORTANT
Register Your Kraus Product
REGISTER TODAY
http://www.kraususa.com/registration
Activate Your Warranty
Access Premium Customer Support
Get Product Information
www.kraususa.com
Loading...