www.kraenzle.com
High-pressure cleaner
LX 2000
LX 200
Operating manual
EN
2 3
EN
Operating manual
High-pressure cleaner
LX 2000
LX 200
Operating manual!
This manual is a translation of the original manual. Read and conform safety
instructions before use! Keep instructions in a safe place for later use and pass
them on to any future user.
4 5
Contents Explanatory symbols
Explanatory symbols used in the operating manual
Failure to observe this note may entail
environmental damage.
Note on the use of the high pressure cleaner that failure to
adhere to the instructions may cause excessive wear or total
breakdown of the LX-series.
Warning!
Failure to observe this note may result in serious injuries!
Explanatory symbols affixed to the high pressure cleaner
In case of improper use, the high pressure jets can be very
dangerous. Do not direct high pressure jet at persons,
animals or active electrical equipment or the high pressure
cleaner itself.
The high pressure cleaner may not be connected directly
to the public drinking water supply network.
Dear customer:
We would like to congratulate you on the purchase of your new high pressure
cleaner and thank you for your confidence in our products!
Your choice has fallen on an absolute quality product!
Kränzle high pressure cleaners are characterized by their convenient and compact
design as well as their high suitability for everyday use.
Highest precision and dimensional accuracy in addition to a technology package
consisting of a multitude of details mark the difference when it comes to
performance, safety and durability.
In order to facilitate handling of the high pressure cleaner, the following pages are
intended to further explain its use. The illustrations may be subject to deviation
depending on the type of equipment or accessory of high pressure cleaner
purchased by you.
Contents ..................................................................................................... 4
Explanatory symbols ..........................................................................
Safety notes ............................................................................................. 6
Description of high pressure cleaner ............................................ 9
General rules ............................................................................................ 11
Functional details .................................................................................. 13
Putting into operation ........................................................................ 18
Direct suction .......................................................................................... 22
Taking out of operation ...................................................................... 23
Small repairs - do it yourself ............................................................. 24
Kränzle accessories ............................................................................... 28
EC declaration of conformity ........................................................... 3
Warranty ................................................................................................... 31
Inspection reports ................................................................................. 32
6 7
Safety notes - This is prohibited!Safety notes
User operating the high pressure cleaner should wear the necessary protective
clothing, i.e. waterproof clothing, rubber boots, safety goggles, headwear etc.
It is prohibited to use the high pressure cleaner in close vicinity to people lacking
suitable protective clothing.
Do not spray against matter containing asbestos or other hazardous substances!
Never spray liquids containing solvents like varnish solvents, petrol, oil or similar
liquids! There is an explosion hazard due to spraying such materials!
Due to the high pressure jet, damage may occur on the objects to be cleaned,
e.g. car tires; therefore, a minimum distance of 30 cm is to be kept!
Prior to putting the high pressure cleaners into operation, check its components
(High pressure hose, power supply cables, safety trigger gun) for any damage.
Replace defect or damaged components!
Replacement of the power supply cables is only permitted by use of an original
power supply cable of the manufacturer and must be performed by a qualified
electrician.
The high pressure cleaner is to be properly used. The user is required to adhere
to local requirements and to watch out for the persons in the danger zone!
The high pressure cleaner is not intended for use by persons with reduced
physical, sensory or mental capabilities, unless such persons are supervised
and capable of perceiving the risks involved in the use of high pressure cleaners!
The water drained through the thermo valve is very hot and may cause burns
in case of skin contact.
Never allow children or untrained persons
to use the high pressure cleaner or to play
with it!
When using high pressure water for cleaning,
make sure that there is a clearly noticeable
recoil effect on the lance. Therefore ensure
a firm footing (see technical data).
Never direct the high pressure jet at power
sockets or any other electrical installations!
Within the working area, all live parts are to
be protected from both water jet and spray
mist.
Never direct the high pressure jet at the
high pressure cleaner itself!
The high pressure cleaner may not be
placed within reach of the high pressure
jet spray mist!
8 9
Safety notes - This is prohibited!
Never direct the high pressure jet at people
or animals!
Never direct the high pressure jet at yourself or other persons, not even to clean
clothing or shoes.
Apply the safety catch on the safety trigger
gun after each use in order to prevent
unintentional spraying!
Only use a power supply cable in perfect
working order!
Do not damage or improperly repair
the power cable (tearing, squeezing,
running over, ...).
Never pull the high pressure hose if it has
formed kinks or “nooses”!
Never pull the high pressure hose over
sharp edges!
Description of high pressure cleaner
Design:
Both the LX 2000 and the LX 2500 are portable type high pressure cleaners.
Please see construction scheme for more details.
1. Handle
2. Pump head made of brass
3. Hose drum with 20 m
steel weave high pressure hose
4. Holders for trigger gun with
safety catch with lance
5. Trigger gun with safety catch
and plug coupling
6. Large stainless steel pressure
gauge
7. On/Off switch
8. Integrated trolley takes rough
ground in its stride
9. Infinitely variable pressure
and quantity regulation
10 11
Description of high pressure cleaner
This is what you have purchased:
1. High-pressure cleaner
LX 2000
LX 2500
2. Trigger gun with safety catch
and plug coupling
3. Stainless steel lance with flat jet
nozzle and quick release coupling
4. Operating manual
Spare par ts list
Optional:
1000 mm turbokiller with stainless
steel lance and plug-in nipple
LX 2000: Ord. no.: 12430-12
LX 200: Ord. no.: 12430-18
Water inlet filter
Ord. no.: 133203
General rules
Intended use
This high pressure cleaner is to be used solely for high pressure water jet cleaning
applications without detergents or low-pressure cleaning work with detergents
(e.g. with a foam injector or washing brush).
Environmental, refuse disposal and water protection regulations
must be observed!
Inspections
The high pressure cleaner must be inspected according to the “Guidelines for
Liquid Spray Devices” at least once every 12 months by a qualified person, to
ensure that continued safe operation is guaranteed. The results of the inspection
are to be recorded in writing (see Inspection reports).
High pressure cleaners used for commercial purposes have
to be checked by a qualified person at least every 12 months!
Accident prevention
The high pressure cleaner is designed for accidents to be impossible if used
correctly. The user is to be notified of the risk of injury from hot machine parts
and the high pressure jet. The “Guidelines for Liquid Spray Devices” must be
complied with.
12 13
General rules
Oil leakage
If oil leaks contact your nearest after-sales service (dealer) at once.
(environmental damage, damage to the transmission).
In case of increased humidity or fluctuations in temperature
development of condensed water is possible. If the oil turns
grey
or white, you must change it.
Oil change
New oil: 1. l
Kränzle high-performance transmission oil (Ord. no.: 400932)
or Motor oil 10W40.
The first oil change should be carried out
after approximately 50 operating hours,
then every year or after 250 operating
hours. If the oil turns grey or white, you
must change the oil. In case of exchanging
oil being required, the oil drain screw must
be opened above a container and the high
pressure cleaner be emptied. The oil is to be
caught in the reservoir and disposed of in an
approved manner.
Functional details
High pressure hose and spray device
The high pressure hose and spray device which are part of the LX-series equipment,
are made of high quality material and engineered to conform with the operating
conditions of the high pressure cleaner and are duly labeled.
If replacement parts are required, only such parts that are authorized
by the manufacturer may be used. The warranty is automatically void if
spare parts of third-party providers are used! The high pressure hose and
spray device must be connected in a pressure-tight manner
(without leakage).
The high pressure hose may not be driven over, pulled excessively, or
twisted. The high pressure hose may under no circumstances be pulled
over sharp edges. Defective high pressure hoses must not be repaired
(acc. to DIN 20022) but have to be replaced by new hoses approved by
the manufacturer.
Prior to putting the high pressure cleaner into operation make sure
that all safety instructions be observed.
14 15
Pressure control valve/safety valve
The pressure control valve/safety valve protects the high pressure cleaner from
a build up of excess pressure, and is designed not to permit an excess pressure
to be selected for operation. The limit nut on the handle is sealed with a spray
coating. The operating pressure and spray rate can be steplessly adjusted by
turning the handle.
Replacements, repairs, new adjustments and sealing should only
be performed by qualified persons.
Motor protection switch
Motor is protected against overload by means of a motor protection switch.
In case of motor overload or blocking, the motor of the high pressure cleaner
switches off automatically. If motor tends to switch off repeatedly, make sure
to detect appears. Make sure to detect and remedy the cause of the failure.
Replacements and inspection work should only be performed by qualified
persons when the high pressure cleaner is disconnected from the power
supply, i.e. with plug pulled out from the electrical socket.
Thermo valve
If HP pump is switched on and trigger gun with safety catch is not operated, the HP
pump continues operation and transports water in the circuit via the bypass valve.
This will heat up the water. For protecting the HP pump against inadmissibly high
temperatures, a thermo valve is installed in the bypass circuit which opens at 63
degrees and drains hot water at the bottom of the HP cleaner via a hose.
Pay attention to splash water when operating HP pump in bypass.
Functional detailsFunctional details
Water and cleaning system
Water must be supplied to the high pressure pump under pressure or directly sucked
in out of a pressureless container. The water is then forced under pressure by the
high pressure pump to the lance. The high pressure jet is formed by the nozzle at
the end of the lance.
Environmental, refuse disposal and water protection regulations
must be observed!
Safety jet pipe with safety trigger gun
The high pressure cleaner can only be operated when the trigger of the safety
deactivation trigger gun‘s trigger is actuated. When the trigger is pulled, the
safety trigger gun opens. The liquid is then transported to the nozzle. The spray
pressure increases and quickly reaches the operating pressure. When the trigger is
released, the safety trigger gun closes and any further spraying of liquid from the
safety jet pipe is prevented. The stainless steel pressure gauge must show 0 bar.
The increase in pressure when the safety trigger gun is closed causes the pressure
control valve/safety valve to open. The motor is switched off by the pressure switch.
The HP pump remains switched on and continues to operate unpressurized via
the bypass. When thesafety trigger gun is opened, the pressure control valve/
safety valve closes, the motor is started and the high pressure pump resumes
pressure spraying from the safety jet pipe with the selected operating pressure.
The safety trigger gun is a safety device. Repairs should only be performed by qualified persons. Should replacement parts be required, use
only components authorized by the manufacturer.
16 17
Functional details
Please note: Lack of water
Lack of water occurs more often than you
probably believe. The more powerful a high
pressure cleaner is the greater is the danger
that a lack of water occurs. If there is only
an insucient amount of water available,
cavitation (water-gas mixture) arises inside
the high pressure pump, which is normally
noticed too late or even not at all. The high
pressure pump will be destroyed. Please
check the available quantity of water by filling a bucket with liter scale for one minute.
Required minimum quantity of water (see technical data).
If the metered quantity of water is too small, you have to use a different water connection, guaranteeing the necessary output. Lack of
water leads to an accelerated wear of the joints (no warranty).
Never let the high pressure pump run dry for more than 60 seconds.
Water supply
Please pay attention to the regulations of your waterworks company! In accordance with DIN EN 61770, the high pressure cleaner
may not be directly connected to the public drinking water supply
lines. A brief connection however is permissible according to DVGW
(German Association for Gas and Water Aairs) if a non-return valve with tube ventilator (Kränzle order no. 41.016 4) is built into the
water supply. Once the water has passed through the non-return
valve it is no longer considered as drinking water. Also indirect
connection to the public drinking water supply lines is permissible
by way of free emission in accordance with EN 61 770; e.g. by using
a reservoir with a float valve. Direct connection to a non-drinking
water supply line is permissible.
Functional details
Insucient quantity of electricity
If there are too many collectors in your
proximity connected to the network at the
same time, the available voltage and the
current intensity may decline. Consequently
the motor of the high pressure cleaner does
not start or even blows. The power supply
may also be insucient if the power supply
cable is too long or too thin. If extension
cables are too long, this may lead to a voltage drop causing malfunctions or start-up
diculties.
Check the line fusing and have the voltage and the available current intensity checked by an expert in case of uncertainty (see technical data).
Electrical connection
The high pressure cleaner is supplied with a 5 meters long power supply cable.
The mains plug must be fitted to a standard grounded socket with a 30 mA
residual current operated device. The socket must be protected with a 16 A delay
action fuse (type C) on the mains side. When using an extension cable, this must
have an earthed lead which is properly connected to the socket. The conductors
in the extension cable must have a minimum cross section of 2.5 mm². Plug connections must be of a spray-proof design, and may not be located on a wet floor.
18 19
3.
The LX-series is a movable high-pressure
cleaner with sturdy trolleys ideally
suited for dicult terrain.
For steering the high-pressure cleaner
put the foot against the tipping
support and then pull the device
towards you.
2. For moving the high pressure cleaner
to the place of use, please release
locking break.
The high-pressure cleaner must not
be pulled with connected water
supply hose!
1. Install the water inlet filter (available as
an option) at the water inlet.
Prior to putting the high pressure cleaner into operation make sure
that all safety instructions be observed.
Neither set up or operate the LX-series in rooms where there is a risk
of fire or explosion nor put it into puddles. Do not use the high pressure
cleaner under water. If, none the less, the high pressure cleaner is
operated in a hazardous area, the applicable safety regulations are
to be observed.
8. After insertion of the lance, release
retaining sleeve and make sure that
the lance is in a secure position.
Grease quick release nipple regularly
using acid-free grease.
7. First pull back the retaining sleeve
of the safety trigger gun, then
insert lance into the plug coupling
sconnection of the safety trigger gun.
6. Pull back securing sleeve of the HP
hose and plug it on trigger gun with
safety catch.
Release securing sleeve and check
for tight fit.
4. Release fixing of hose drum and fully
uncoil it after that. (When using high
pressure hose extensions take care
that the max. length of 20 m is not
exceeded!)
5. Hose drum must be unrolled
completely.
Provide for firm and pressure-tight
connection of HP hose to pump outlet.
Prior to insertion, check plug coupling connection of lance for
cleanliness (sand, dirt ..) and use clear water to clean, if necessary.
Impurities may damage the sealing in the plug coupling.
Accessories may only be connected to a Kränzle-approved trigger gun
with safety catch.
Putting into operation Putting into operation
20 21
10. Connect the water hose to water
inlet sieve. The high-pressure cleaner
may be connected to a water mains
(1-10 bar pre-pressure) with either cold
or hot water (up to 60 °C).
The LX-series provides the opportunity
of sucking in water out of a container
(see direct suction).
Be careful when using hot water!
When running your high-pressure cleaner with hot water of 60 °C raised
temperatures occur. Do not touch the metal parts of the high-pressure
cleaner without safety gloves!
11. Each time check oil level at the oil
dipstick prior to putting the high
pressure cleaner into operation.
Oil level must be visible in the middle
of the oil sight glass.
9. If using a water inlet filter check it
for cleanliness prior to each startup.
Manually unscrew filter bowl, remove
sieve and thoroughly rinse and clean
with the rest of the parts in clear water.
If the sieve is dirty, water cannot get
through and pressure will not build up.
Check the water inlet sieve for damage.
Do not operate the high-pressure cleaner using the damaged filter.
13. Switch on high pressure cleaner with
opened safety trigger gun. Bleeding
of the high pressure cleaner: Pull and
release trigger of safety trigger gun
several times. Start cleaning task.
12. Connect to circuit (see technical data).
The socket must be protected on the
mains side with a 16 A delay fuse
(type C).
14. Adjust operating pressureinfinitely
using the rotary handle. The maximum
pressure is factory-set.
15.
The LX series is equipped with 2 supports
for the trigger gun with safety catch with
lance.
Putting into operation Putting into operation
Do not touch the mains plug or any live parts with wet or moist hands.
22 23
Direct suction
Direct water extraction
Due to the suction capacity of its high pressure pump (up to 2.5 m suction height,
max. hose length 3 m) this high pressure cleaner can suck in water for cleaning
purposes from separate containers or ponds.
2. Put filled suction hose into the waterfilled container and start the cleaning
job. Use clean water only! Never suck
in water containing chlorine! Do not
suction air!
1. Mount suction hose with suction filter
(Item no.: 15033).
Prior to starting the first suction the high pressure pump and the
suction hose has to be filled with water!
Note
Depending on the water quality it may occur after a prolonged standstill
that the valves get sticky. Consequently the high pressure cleaner cannot
properly suck in water from a container. In this case connect a hose with
pressurized water to the pump inlet. Having started the high pressure
cleaner the pressurized water opens the valves and the machine resumes
sucking in water from the container. Now you can carry on with your
cleaning task as usual.
Taking out of operation
1. Switch off the high pressure cleaner
2. Cut off the water supply
3. Open the safety trigger gun catch briefly until the pressure is released
4. Apply safety catch on the trigger gun
5. Remove high pressure hose and safety trigger gun
6. Emptying high pressure pump: Hold high pressure hose and switch
motor on until water jet stops escaping at the outlet.
7. Pull the plug from the socket
8. Clean high pressure hose and wind up without loops, fix hose drum
9. Clean and wind up the power supply cable
10. Clean the water inlet sieve
11. Apply locking brake
12. Store high pressure cleaners in frost-free rooms in winter
Frost protection
For protecting the high-pressure cleaner against frost please empty it completely.
Separate high-pressure cleaner from water supply and switch it on.
By opening
the trigger gun the high-pressure pump presses water out of the high-pressure
cleaner. However, do not allow the device to operate without water for more
than one minute.
24 25
The stainless steel pressure gauge shows
full pressure, but from the nozzle comes
only little water or no water at all.
(Inside the stainless steel pressure gauge is
no water but a filling with glycerin to damp
the vibration of the pointer.)
Proceeding:
Switch off the high pressure cleaner. Pull
plug from the socket. Operate safety trigger
gun catch several times to decrease the
pressure.
Unplug trigger gun with safety catch and
lance first, then rinse high pressure hose to
remove possible soiling.
If the problem still exists, take wire (paper
clip) and push through nozzle opening. If
this procedure is not successful, the nozzle
has to be replaced.
Problem
No water from nozzle although the high pressure cleaner is running.
The stainless steel pressure gauge shows full pressure.
Cause
Most likely the nozzle is blocked.
Pull plug from socket prior to starting any repair work!
The stainless steel pressure gauge shows
low pressure despite fully turned up pressure regulation. The water from the lance
comes in squirts. The high pressure hose
vibrates.
(Inside the stainless steel pressure gauge is
no water but a filling with glycerin to damp
the vibration of the pointer.)
Problem
Irregular jet from nozzle.
The stainless steel pressure gauge shows low pressure.
Cause
Most likely the valves are soiled or sticky.
Small repairs - do it yourself Small repairs - do it yourself
Proceeding:
Unscrew all 6 valves, one after the other
(hexagonal brass screws, 3 in a row,
vertically and horizontally)
Take out valve body and O-ring by means
of needle nose pliers. Check O-ring for
damage. In case of a damage the O-ring
has to be replaced.
Take a wire (paper clip) and clean valves
under running water.
Do not forget the O-ring during reassembly!
26 27
Proceeding:
Switch off the high pressure cleaner and
pull plug from socket. Stop water supply.
Operate safety trigger gun catch several
times to decrease the pressure.
Unscrew control valve.
There is no guarantee if the high pressure pump is damaged by
defective O-rings due to air induction or lack of water (cavitation).
Remove check body and check O-Ring for
soiling or damage. Also check seal seat in
the control valve for dirt or damage.
If sealing rings are defective replace
O-rings at once.
Small repairs - do it yourself Small repairs - do it yourself
Problem
After closing the safety trigger gun the high pressure cleaner
keeps switching on and off.
The stainless steel pressure gauge continuously displays full pressure.
Possible cause No. 1
Leckage.
Having closed the trigger gun with safety catch, the high pressure cleaner must
shut down and the stainless steel pressure
gauge must show „0“ bar. If not shut down
and the stainless steel pressure gauge continuously shows full pressure, this could be
due to leakage at the high pressure pump,
at the pressure switch, at the high pressure
hose or at the trigger gun with safety catch.
In case of a leakage there is no guarantee for possible
consequential damages.
Proceeding:
Check connections from the high pressure
cleaner to the high pressure hose and from
the high pressure hose to the safety trigger
gun and also the connection between lance
and safety trigger gun for tightness.
Switch off the high pressure cleaner.
Shortly press the trigger of the safety
trigger gun to decrease the high pressure
cleaner. Unscrew high pressure hose,
safety trigger gun and lance and check
the O-rings. If the O-rings are damaged
they have to be replaced.
Problem
After closing the safety trigger gun the high pressure cleaner
keeps switching on and off.
The stainless steel pressure gauge continuously displays full pressure.
Possible cause No. 2
The non-return valve is defective.
28 29
The high pressure cleaner accessories are safety components!
Any warranty will be void if parts not authorised by Kränzle are used.
Please indicate the technical data of the high pressure cleaner
(device type) when placing your order.
Double lance
With insulated ISO handle
With plug-in nipple
Low pressure nozzle
D3035 as standard
Suction hose
with suction filter
With return valve
Hose length 3 m
Item no.: 15033
LX 2000:
Item no.: 12133-D40125
LX 2500:
Item no.: 12133-D40175
Adapter for accessories
with screw connections
With quick release nipple
For item no.: 12440 (fig. left)
400 mm extension
With grip plates
Item no.: 12440 (fig. left)
Item no.: 12441 (fig. right)
* in combination with adap ter only
Washing brush, cross
*
Brush head L 240 x W 90 mm
Connection thread 1/4"
female thread
Item no.: 410500
Splash guard
L: 280 mm x W: 190 mm
For all washing lances
Item no.: 132600
Turbokiller lance
With stainless steel pipe
1000 mm
With plug-in nipple
Item no.: 41570-042
Kränzle accessoriesKränzle accessories
30 31
Kränzle LX 2000
Kränzle LX 2500
Kränzle LX 2000: 1920 l/h
Kränzle LX 2500: 2490 l/h
Fa. Josef Kränzle GmbH & Co. KG
Manfred Bauer
Rudolf-Diesel-Str. 20, 89257 Illertissen
Machinery directive 2006/42/EC
EMC-directive 2004/108/EC
Noise directive 2005/88/EC,
Art. 13 HP water spraying machines
Annex 3, part B, chapter 27
88 dB (A)
91 dB (A)
Annex V, Noise directive
2005/88/EC
EN 60 335-2-79: 2015
EN 55 014-1: 2006
EN 61 000-3-2: 2014
EN 61 000-3-3: 2013
WarrantyEC declaration of conformity
We here by declare that the design of
the high pressure cleaners:
Nominal flow:
technical specifications available
from:
comply with the following guidelines
and their amendments for high
pressure cleaners:
Sound level measured:
Sound level guaranteed:
Applied conformity assessment
procedure:
Applied specifications and standards:
The warranty obligation of Josef Kränzle GmbH & Co. KG towards the dealer
from whom you have purchased this Kränzle high-pressure cleaner (= product)
applies to material faults only such as material and manufacturing defects.
Defects attributable to long and frequent use of the product, typically arising
due to the age of the high-pressure cleaner and intensity of its use are defined
as normal wear in respect of product components. Purchaser’s rights to assert
claims for such defects are ruled out. Parts subject to wear include in particular
the pressure gauge, nozzle, valves, sleeves, high-pressure hose and spray equipment.
The product is to be operated in conformity with this operating manual.
The operating manual is deemed to be part of the warranty provisions.
Any changes made to the safety devices of the product or instances of
maloperation – such as exceeding the temperature and speed limits,
undervoltage, insufficient water supply and sewage water, or failure to
use the product for the intended purpose – may result in damage occurring
to the product. Such damage is not deemed to constitute any material defect.
Should the use of accessories or spares other than original Kränzle component parts
und original Kränzle replacement parts be the cause of defects on our product,
this may lead to all warranty claims becoming null and void. Only the use of
original Kränzle replacement parts matching the relevant Kränzle high-pressure
cleaner provides adequate assurance for safe and trouble-free operation of the
Kränzle high-pressure cleaner.
With regard to legal warranty claims, the limitation periods of the respective
countries shall apply.
Where warranty claims apply to any other defects, please contact your
local dealer, presenting the accessories together with your purchase receipt,
or the nearest authorised service centre. This can also be found on the
internet under
www.kraenzle.com.
Ludwig Kränzle
(Managing direc tor)
Josef Kränzle GmbH & Co. KG
Rudolf-Diesel-Straße 20
89257 Illertissen (Germany)
Illertissen, 2017-01-12
32 33
Inspection reports Inspection reports
Ow ner: .................................................................................
Address: ...............................................................................
.....................................................................................................
Typ e: .......................................................................................
Serial no.: .............................................................................
Repair order no.: .............................................................
Inspection result (check)
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment, the defects found have been rectified so that the
Labour Safety can be confirmed.
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the
defects found are rectified by repair or replacement of the faulty parts.
Scope of insp ection o.k. yes no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering , Protective device
Pressure line (tightness)
Stainless steel pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
High pressure hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding
power supply cable (damage)
Protective conductor (connected)
On / O switch
Inspection data determined value se t value
High pressure nozzle
Operating pressure ………………bar
Switch o pressure ……………..bar
protective conductor resistance not exceeded / value
Insulation
Leakage current
Safety trigger gun locked
The next retest according to the Guidelines for Liquid Spray Equipment has to be
carried out by: Month
................................................................... Year .......................................................................
Place, Date .......................................................................... Signature ...............................................................................
High pressure cleaners for industrial use have to be checked by an expert every
12 months! Inspection report on annually carried out Labour Safety Inspection (UVV)
according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves
as proof for the completion of the retest and must be kept carefully!)
Kränzle-test seals: It em no.: UVV200106
Ow ner: .................................................................................
Address: ...............................................................................
.....................................................................................................
Typ e: .......................................................................................
Serial no.: .............................................................................
Repair order no.: .............................................................
Inspection result (check)
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment, the defects found have been rectified so that the
Labour Safety can be confirmed.
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the
defects found are rectified by repair or replacement of the faulty parts.
Scope of insp ection o.k. yes no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering , Protective device
Pressure line (tightness)
Stainless steel pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
High pressure hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding
power supply cable (damage)
Protective conductor (connected)
On / O switch
Inspection data determined value se t value
High pressure nozzle
Operating pressure ………………bar
Switch o pressure ……………..bar
protective conductor resistance not exceeded / value
Insulation
Leakage current
Safety trigger gun locked
The next retest according to the Guidelines for Liquid Spray Equipment has to be
carried out by: Month
................................................................... Year .......................................................................
Place, Date .......................................................................... Signature ...............................................................................
High pressure cleaners for industrial use have to be checked by an expert every
12 months! Inspection report on annually carried out Labour Safety Inspection (UVV)
according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves
as proof for the completion of the retest and must be kept carefully!)
Kränzle-test seals: It em no.: UVV200106
34 35
Notes Notes
www.kraenzle.com
Josef Kränzle GmbH & Co. KG
Rudolf-Diesel-Straße 20
89257 Illertissen (Germany)
sales@kraenzle.com
Made
in
Germany
© Kränzle 10.01.2019 / Ord. no.: 306180 / Subject to technical modifications and errors.
Loading...