Kranzle B170T, B200T, B230T, B240T, B270T Operating Manual
GB
Operating manual
High-pressure cleaners
Read and conform safety instructions before use!
Keep instructions in a safe place for later use and
pass them on to any future user.
2
10 - 250 bar
270 bar
16 l/min
70 °C
2,5 m
20 m
GX 390 LX2
83 kg
103 dB (A)
appr. 42 Nm
36 Nm
41 193 1*
Dear customer
We would like to congratulate you on your new mobile high pressure cleaner and
to thank you for the purchase.
To ease your introduction to the use of the cleaner, we have provided the following
pages of explanations, tips and hints, which we ask you to read before using for
the rst time.
The equipment will assist you professionally in all cleaning tasks, e.g.:
- facades
- agstones
- terraces
- vehicles of all types
- sheds
- machines etc.
Description
- barrels and containers
- channels
- Streets etc.
Operating pressure,
steplessly adjustable
Perm. overpressure
Water output
at 1800 rpm
Hot water input
Suction height
High pressure
hose
with hose drum
Combustion motor
Honda
Weight
Sound level Gua-
ranteed sound level L
WA
Recoil at lance
Torque
Order n°:
Technical
data
B 240 T
B 200 TB 170 T
10 - 150 bar
165 bar
13 l/min
70 °C
2,5 m
20 m
GX 160 LX2
58 kg
103 dB (A)
appr. 32 Nm
29 Nm
41 190 1
10 - 165 bar
180 bar
12 l/min
70 °C
2,5 m
20 m
GX 200 LX2
58 kg
103 dB (A)
appr. 27 Nm
24,3 Nm
41 191 1
10 - 220 bar
240 bar
16 l/min
70 °C
2,5 m
20 m
GX 340 LX2
83kg
103 dB (A)
appr. 38 Nm
33 Nm
41 192 1*
Permissible tolerance for gures ± 5 % in acc. with VDMA uniform sheet 24411
with speed control *
B 270 T
(Assumed length of lance: 0,9 m)
10 - 200 bar
230 bar
20 l/min
50 °C
2,5 m
20 m
GX 390 LX2
83 kg
103 dB (A)
appr. 42 Nm
36 Nm
41 194 1*
B 230 T
Spec. appliance
*1
*1
Minimum quantity of water to be led to the equipment!
3
Water
7
8
5 Unloader valve - safety valve
6 High pressure hose
7 Spray gun
8 Interchangeable lance with high
pressure nozzle
1 Water inlet connection with lter
2 Suction hose with lter (special
accessory) Order no. 15.038 3
3 High pressure pump
4 Press. gauge with glycerin lling
The KRÄNZLE B170 T + B200 T + B230 T+ B240 T + B270 T - high pressure
cleaners are mobile machines. The design can be seen from the diagram.
Construction
Item
Description
1
2
5
6
4
Description
Water and Cleaning / Pegemittel System
Water can be connected at mains pressure to the high pressure pump or it can
be sucked directly from a storage tank. The water is then forced under pressu
-
re by the high pressure pump to the lance. The high pressure jet is formed by
the nozzle at the end of the lance.
Detergent and caring agents can be added through a high pressure injector
(special accessory). Up to max 20m HP hose length.
The rules concerning the environment, refuse and ground water
protection must be complied with!
(Information to be obtained from environmental dept, town
works, etc.)
Lance with trigger gun
The machine can only be operated when the safety trigger is squeezed. The
machine can only be operated when the safety trigger is squeezed.
When the lever is squeezed, the spray gun opens. The liquid is then pumped
to the nozzle. The spray pressure increases and quickly reaches the selected
operating pressure.
When the trigger is released, the trigger gun closes and any further spraying of
liquid from the lance is stopped.
The increase in pressure when the trigger gun is closed causes the unloader
valve-safety valve to open. The pump remains switched on and continues to
pump liquid through the pump at reduced pressure. When the trigger gun is
opened, the unloader valve - safety valve closes and the pump ressumes pres
-
sure spraying from the lance
The trigger gun is a safety device. Repairs should only be performed by qua
-
lied persons. Should replacement parts be required, use only
components authorized by the manufacturer.
Unloader valve - safety valve
The unloader valve - safety valve protects the machine from a
build p of excess pressure, and is designed not to permit an excess pressure
to be selected for operation. The limit nut on the handle is sealed with a spray
coating.
The operating pressure and spray rate can be steplessly adjusted by turning
the handle.
Replacements, repairs, new adjustments and sealing should only be performed
by qualied persons.
5
Description
For the motor follow the Honda operating manual
only.
Motor-safety: (see Honda operating manual)
Honda motors are safe and reliable if they are operated correctly. Read the operating manual carefully before using the motor and try to understand the contents of
the manual completely.
Not following this advice could lead to injuries or damage of the equipment.
To avoid a possible re hazard and to ensure the necessary ventilation
the motor has to be operated at a distance of at least 1 m from buil-
dings and objects. Inammable objects have to be kept away from the
surrounding area of the motor.
Children and pets have to be kept away from the motor, as there is
a danger of suffering burns from hot motor parts and to be injured by
equipment driven by the motor.
Get to know the motor and especially learn how to switch it off quickly.
Do not allow persons to operate the motor who are not familiar with it.
When running your high pressure cleaner with hot water of 70° C (with
B230 T 50°) raised temperatures occur.
Do not touch the machine without safety gloves.
CAUTION !
Never use liquid containing solvents such as paint thinners, petrol, oil or similar li-
quid matter. Pay attention to the instructions of the manufacturers of the
cleaning agents. The seals in the machine are not resistant to solvents.
The spray of solvents is inammable, explosive and poisonous.
Neither set up and operate the machine in rooms where there is a risk
of re or explosion nor put it into puddles. Do not use the machine
under water.
Do NOT !! tilt or turn round the high-pressure cleaner during transport
or operation for longer than 1 minute!
CAUTION !
Setting up: Location
6
Description
Please check that the high pressure cleaner has available the quantity of water
specied on page 2 (techn. specs.) (Litres per minute).
Water connection:
Test:
Allow the water supply hose to run for 1 minute into a bucket.
The received quantity of water must be at least the quantity given on page 2 !!!
Lack of water causes fast wear on seals (no warranty)
Brake
The high-pressure cleaner is tted with a brake that prevents the machine from
rolling away on uneven ground.
Always apply the brakes rmly when working with the machine !!!
7
Description
Brief operating instructions
1. Connect the high pressure hose with spray gun
and machine.
2. Connect the suitable water supply.
3. Flush the air from the pump (open and close the spray gun
several times).
4. Switch on the motor while the spray gun is open and
commence cleaning.
5. After completing the work, completely empty the pump
(switch the motor on for approximately 20 seconds without the suction
and pressure hose).
- Only use clean water ! Protect from frost !
- Do NOT !! tilt or turn round the high-pressure cleaner during
transport
CAUTION !
Please pay attention to the regulations of your waterworks company.
In accordance with EN 61 770, the machine may not be directly connected to the
public drinking water supply lines.
A brief connection however ist permissible according to DVGW (German Asso-
ciation for Gas and Water Affairs) if a tube ventilator with check valve (KRÄNZLE
Order-No. 41.016 4) is built into the water supply.
Also indirect connection to the public drinking water supply lines is permissible by
way of free emission in accordance with EN 61 770; e.g. by using a reservoir with
a oat valve.
Direct connection to a non-drinking water supply line is permissible.
High pressure hose and spray device
The high pressure hose and spray device supplied with the machine are made
of high grade material, they are also optimized for the machine and marked as
required by the appropriate regulations.
If replacement parts are required, only such parts that are authorized
by the manufacturer and which bear the markings required by the appropriate regulations may be used. The high pressure hose and spray
device must be connected in a pressure-tight manner. The high pressure hose may not be driven over, pulled excessively, or twisted. The
hose may under no circumstances be pulled over sharp edges, since
otherwise the guarantee is automatically void.
8
As to the recoil
- see notice on
page 2!
Always aim the underbody
lance. Note when using an
angled underbody lance,
like for example lance No.
41075, that there is a certain amount of torque in the
recoil.
(See also notice on page 2)
Apply the safety catch on the spray
gun after each use, in order to pre-
vent unintentional spraying!
Safety notes
9
2. Spray lance with high pressure
nozzle, at spray
4. KRÄNZLE - high-pressure cleaners
B 170 T
B 200 T
B 240 T
B 270 T
B 230 T
incl. hose drum with 20 m HP-hose
6. Water lter
This is what you’ve purchased:
1. Spray gun with insulated
pistol grip and screw connection
3. Turbokiller
5. Operation manual pump
Operation manual motor
10
1. Check oil level
( Pump and motor)
Preparation for use
3. Unroll hose without kinks and connect with handgun and pump. Use
HP hose of max. 20 m length.
High pressure hose connected
to machine and spray gun.
2. Connect high pressure lance or
Turbokiller to the spray gun.
11
Water
5. Maximum induction
height 2.5 m - see technical data
on page 2.
Please make sure that the lter is
clean before using your high pressure
cleaner.
4. The machine can be connected
to a pressurised water line with cold
or up to 70 °C hot water (see page 2).
Ensure that the water supply ist clean
when sucking from external sources.
The hose cross section must be
at least 1/2“ = 12.7 mm (free
passage). Filter must
always be clean.
Preparation for use
Adjusting the pressure
This is accomplished by
turning the handwheel.
The default setting is
maximum pressure.
1. Switch off the machine
2. Cut off the water supply
3. Open the spray gun briey until the pressure is released
4. Apply the safety catch on the spray gun
5. Remove the water hose and high pressure hose
6. Drain the pump: switch on the motor for approx. 20 seconds
7. Winter: store the pump in rooms above 0° C
8. Clean the water lter
To shut down the pump:
12
This is prohibited !
Never allow children to
use the high pressure
cleaner !
Never direct the water jet at the machi-
ne itself !
13
Never direct the water
jet at people or animals
!
Never pull the high pres-
sure hose if it has for-
med kinks or “nooses”!
Never pull the hose
over sharp edges !
This is prohibited !
14
Additional KRÄNZLE-accessories for ...
Environmental, refuse disposal and water protection regu-
lations must be observed when using the accessories!
Rotary scrubbing brush
Order No. 41.050 1
Sandblaster
Order No. 41.068 1
Underbody lance
Order No. 41.075
Flat brush
Order No.41.073
Drain and pipe cleaning hose
8 m - Order No. 41.051
15 m - Order No. 41.058
15
Car cleaning, glass, caravan, boat etc.
rotary washing brush with 40 cm exten-
sion and ST 30 nipple M 22 x 1,5
Cleaning cars and all smooth surfaces :
brush with ST 30 nipple M 22 x 1,5.
Underbody cleaning of cars, trailers and
equipment: lance 90 cm with high pressure
nozzle and ST 30 nipple M 22 x 1,5.
The lance must be aimed when spraying.
Cleaning pipes, channels and drains:
pipe cleaning hose with KN nozzle
and ST 30 nipple M 22 x 1,5
When sandblasting you must wear
protection clothes! Pay attention to the
instructions of the manufacturer of the
abrasive!
Blasting old paint, rust and facades: sand-
blasting injector with suction lance, 3 m PVC
hose and ST 30 nipple.
... further combination possibilities
Rotary point sprayer for extreme soiling.
Dirtkiller with 40 cm extension and ST 30
nipple M 22 x 1,5.
Loading...