Kranzle B 10 200, B 13 150, B 16 220 Operating Manual

Operating manualOperating manual

Operating manual

Read and conform Read and conform

Read and conform

safety instructions safety instructions

safety instructions

before use before use

before use

High prHigh pr

High pr

essuressur

essur

e cleanerse cleaners

e cleaners

B 10/200 B 13/150 B 16/220

Dear Customer

We would like to congratulate you on your new portable/mobile high pressure cleaner and to thank you for the purchase.

To ease your introduction to the use of the cleaner , we have provided the following pages of explanations, tips and hints.

The equipment will assist you professionally in all cleaning tasks, e.g.:

- facades

- flagstones

- terraces

- vehicles of oll types

- sheds

- channels

DescriptionDescription

Description

- barrels and containers

- machines

- streets

technical

specifications

B 16/220B 13/150B 10/200

10 - 200 bar

220 bar

at 1800 rpm

10 l/min

70 °C 2,5 m

10 m

Honda GX 200 LX

22 kg 78 dB

approx. 32 Nm

29 Nm

41.182

41.182 1

10 - 150 bar

165 bar

at 1800 rpm

13 l/min

70 °C 2,5 m

10 m 15 m

Honda GX 160 CX

24 kg 78 dB

approx. 27 Nm

24,3 Nm

41.170

41.170 1

41.170 2

10 - 220 bar

240 bar

at 1800 rpm

16 l/min

70 °C 2,5 m

10 m 15 m

Honda GX 340 CX

26 kg 81 dB

approx. 38 Nm

33 Nm

41.173 2

41.173 3*

41.173

Permissible tolerance for figures ± 5 % in accordance with VDMA uniform sheet 24411

(assumed lenght of lance: 0,9 m)

operating pressure, steplessly adjustable

permissible overpressure

water output

hot water input up to suction height high pressure hose

with hose drum engine weight sound level

according to DIN 45 635 recoil at lance

torque

order No. portable

with undercarriage with undercarriage

and hose drum

with speed control *

Item

water

6 Injector for cleaning agents (not with B10/200) 7 High pressure hose 8 Spray gun assembly 9 Interchangeable lance 10 Regulator nozzle 10a B10/200 only with dirt-killer

1 Water inlet connection with filter 2 Suction hose with filter (special accessory) order No. 15.038 3 3 High pressure pump 4 Pressure gauge with glycerin filling 5 Unloader valve - safety valve

The KRÄNZLE B 10/200 + B 13/150 + B 16/220 - high pressure cleaners are portable/mobile machines. The design can be seen from the diagram.

Construction

DescriptionDescription

Description

The machine can only be operated when the safety trigger is squeezed. When the lever ist squeezed, the spray gun opens. The liquid is then pumped to the

nozzle. The spray pressure increases and quickly reaches the selected operating pressure.

When the trigger ist released, the trigger gun closes and any further spraying of liquid from the lance ist stopped.

The increase in pressure when the trigger gun is closed causes the unloader valvesafety valve to open. The pump remaines switched on and continues to pump liquid through the pump at reducated pressure. When the trigger gun ist opened, the unloader valve - safety valve closes and the pump ressumes pressure spraying from the lance.

The trigger gun is a safety device. Repairs should only be performed by qualified persons. Should replacement parts be required, use only components authorized by the manufacturer .

Lance with trigger gun

The unloader valve - safety valve protects the machine from a build-up of excess pressure, and is designed not to permit an excess pressure to be selected for operating. The limit nut on the handle is sealed with a spray coating.

The operating pressure and spray rate can be steplessly adjusted by tuning the handle.

Replacements, repairs, new adjustments and sealing should only be performed by qualified persons.

Unloader valve - safety valve

Environmental, refuse disposal and water protection regulations must be observed !

Water - and Cleang - Care System

Water can be connected at mains pressure to the high pressure pump or it can be sucked directly from a storage tank. The water is then forced under pressure by the high pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of the lance. Cleaning and caring agents can be mixed with the water by a low pressure injector .

(not with B10/200)

DescriptionDescription

Description

DescriptionDescription

Description

For the motor follow the HondaFor the motor follow the Honda

For the motor follow the Honda operating manual onlyoperating manual only

operating manual onlyoperating manual only

operating manual only

Motor-safety: (see Honda operating manual)

Honda motors are safe and reliable if they are operated correctly . Read the operating manual carefully before using the motor and try to understand the contents of the manual completely .

Not following this advice could lead to injuries or damage of the equipment.

To avoid a possible fire hazard and to ensure the necessary ventilation the motor has to be operated at a distance of at least 1 m from buildings and objects. Inflammable objects have to be kept away from the surrounding area of the motor .

Children and pets have to be kept away from the motor, as there is a danger of suffering burns from hot motor parts and to be injured by equipment driven by the motor.

Get to know the motor and especially learn how to switch it off quickly. Do not allow persons to operate the motor who are not familiar with it.

When running your high pressure cleaner with hot water of 70° C raised temperatures occur .

Do not touch the machine without safety gloves.

CAUTION !

Never use liquid containing solvents such as paint thinners, petrol, oil or similar liquid matter. Pay attention to the instructions of the manufacturers of the cleaning agents. The seals in the machine are not resistant to solvents. The spray of solvents is inflammable, explosive and poisonous.

Neither set up and operate the machine in rooms where there is a risk of fire or explosion nor put it into puddles. Do not use the machine under water .

CAUTION !

Setting up: Location

DescriptionDescription

Description

Brief operating instructions

1. Connect the high pressure hose with spray gun and machine.

2. Connect the suitable water supply .

3. Flush the air from the pump (open and close the spray gun several times).

4. Switch on the motor while the spray gun is open and commence cleaning.

5. After completing the work, completely empty the pump (switch the motor on for approximately 20 seconds without the suction and pressure hose). Afterwards you can roll up the high pressure hose.

- Only use clean water ! Protect from frost !

CAUTION !

Please pay attention to the regulations of your waterworks company . In accordance with DIN 1988, the machine may not be directly connected to the

public drinking water supply lines. A brief connection however ist permissible according to DVGW (German

Association for Gas and Water Affairs) if a tube ventilator with check valve (KRÄNZLE Order-No. 41.016 4) is built into the water supply .

Also indirect connection to the public drinking water supply lines is permissible by way of free emission in accordance with DIN 1988, part 4; e.g. by using a reservoir with a float valve.

Direct connection to a non-drinking water supply line is permissible.

High pressure hose and spray device

The high pressure hose and spray device supplied with the machine are made of high grade material, they are also optimized for the machine and marked as required by the appropriate regulations.

If replacement parts are required, only such parts that are authorized by the manufacturer and which bear the markings required by the appropriate regulations may be used. The high pressure hose and spray device must be connected in a pressure-tight manner . The high pressure hose may not be driven over, pulled excessively, or twisted. The hose may under no circumstances be pulled over sharp edges, since otherwise the guarantee is automatically void.

Always aim the underbody lance. Note when using an angle underbody lance, like for example lance

No. 41.075, that there is a certain amount of torque (twisting motion) in the recoil. (See also notice on page 2).

As to the recoil see notice on page 2.

Apply the safety catch on the

spray gun after each use, in

order to prevent

unintentional spraying.

Safety notesSafety notes

Safety notes

This is what you´ve purchased :This is what you´ve purchased :

This is what you´ve purchased :

1. Spray lance with regulator and

high pressure nozzle, flat spray (B10/200 only with dirt-killer)

2. Spray gun with insulated pistol

grip and screw connection

3. KRÄNZLE - High pressure cleaner

B 10/200 B 13/150 B 16/220

4. High pressure hose 10 m

15 m HP-hose for cleaners with hose drum

5. Suction hose

6. Operating instructions pump Operating instructions motor

7. Washing powder specimen

8. Water inlet components

1. Oil-measuring stick

Prepare for usePrepare for use

Prepare for use

2. Connect the high pressure lance to the spray gun.

3. Unwind the high pressure hose without leaving kinks or "nooses" and connect it to the spray gun and pump. When using extension hoses, use max. 20 m high pressure hose, or 2 x 10 m with hose connectors.

The high pressure hose connected from the machine to the lance.

Water

CAUTION !

5. Maximum induction height 2.5 m

- see technical data on page 2.

Please make sure that the filter is clean before using your high pressure cleaner.

4. The machine can be connected to a pressurised water line with cold or 60 °C respectively 70 °C hot water

(see page 2). Ensure that the water supply ist clean

when sucking from external sources.

The hose cross section must be

at least 1/2" = 12.7 mm (free

passage). Filter 1 must

always be clean.

Preparation for usePreparation for use

Preparation for use

When running your high pressure cleaner with hot water of 70° C raised temperatures occur .

Do not touch the machine without safety gloves.

Preparation for usePreparation for use

Preparation for use

1. Switch off the machine

2. Cut off the water supply

3. Open the spray gun briefly until the pressure is released

4. Apply the safety catch on the spray gun

5. Remove the water hose and high pressure hose

6. Drain the pump: switch on the motor for approx. 20 seconds

7. Winter: store the pump in rooms above 0° C

8. Clean the water filter

To shut down the pump:

Note that you must always comply

with the instructions provided by the

manufacturer of the cleansing

agent (e.g. instructions

concerning safety clothing) and the water protection egulations.

A mixing ratio of 3-5% is achieved when the Vario-Jet is fully turned on. pH value neutral 7-9.

Place chemical filter no. 5 in the reservoir with the cleansing agent. Turn on Vario-Jet No. 4 to enable the injector to induct the cleansing agent. By turning back the Vario-Jet nozzle, the supply of chemical is automatically cut off. Allow the cleansing agent to take effect and then remove with high pressure spray.

When using cleansing agents:

Adjusting the pressure

This is accomplished by turning the handwheel. The default setting is maximum pressure.

p max.

Chem.

Turn on regulator nozzle to reach low pressure.

This is prohibitedThis is prohibited

This is prohibited

Never allow children to use the high pressure cleaner !

Never direct the water jet at the machine itself !

Never direct the water jet at people or animals !

Never pull the high pressure hose if it has formed kinks or "nooses"! Never pull the hose over sharp edges !

This is prohibitedThis is prohibited

This is prohibited

Additional KRÄNZLE accessoriesAdditional KRÄNZLE accessories

Additional KRÄNZLE accessories

(not with B 10/200)

Environmental, refuse disposal and water protection regulations must be observed when using the accessories.

Rotary scrubbing brush

Order No. 41.050 1

Sandblaster

Order No. 41.068 1

Underbody lance, new

Order No. 41.075

Flat brush

Order No. 41.073

Drain and pipe cleaning hose

8 m - Order No. 41.051 15 m -

Order No. 41.058

Dirtkiller B 10/200

Order No. 41.073 8

B13/150

Order No. 41.072 5

Turbokiller B 16/220

Order No. 41.072 4

for further combination possibilitiesfor further combination possibilities

for further combination possibilities

Car cleaning, glass, caravan, boat etc.: rotary washing brush with 40 cm extension and ST 30 nipple M 22

Cleaning cars and all smooth surfaces: brush with ST 30 nipple M 22.

Underbody cleaning of cars, trailers and equipment: lance 90 cm with high pressure nozzle and ST 30 nipple. The lance must be aimed when spraying.

Blasting old paint, rust and facades: sandblasting injector with suction lance and 3 m PVC hose and ST 30 nipple M 22.

Rotary point sprayer for extreme soiling: dirt killer with 40 cm extension and ST 30 nipple M 22.

Cleaning pipes, channels and drains: Pipe cleaning hose with KN nozzle and ST 30 nipple M 22.

When sandblasting you must wear protection clothes! Pay attention to the instructions of the manufacturer of the abrasive.

Small repairs –Small repairs –

Small repairs –

The pressure gauge shows a 10% higher pressure than the working pressure.

The injector may be dirty

and you

should first remove

the hose.

Now turn on the water and you should get a

powerful stream of water,

but if you only get a weak

flow of water

then straighten

a paper clip,

and release the

injector with an

open-ended

spanner.

Check that it

is clean.

Reconnect the hose,

and you are

ready to continue

your work.

Y ou only get a weak flow of water or no water at all !

Remove the injector

together with the

spring and return

valve.

Cleaning the injector through from both sides and replace the return valve.

+ 36 hidden pages

Kranzle B 10 200, B 13 150, B 16 220 Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual