Kramer Electronics, Ltd.
USER MANUAL
BoardView™ Models:
Kit 2V:
Kit 2AV:
Kit 4V:
Kit 4AV:
Kit 8V:
Kit 8AV:
TP-107V (2 units) and TP-120
TP-107AV (2 units) and TP-122
TP-107V (4 units) and TP-120
TP-107AV (4 units) and TP-122
TP-107V (8 units) and TP-120
TP-107AV (8 units) and TP-122
RC-108
RC-116
, Presentation Controller
, Presentation Controller
Contents
Contents
1
Introduction 1
1.1 The C-STP+KNET-6 Cable 2
2
Getting Started 2
2.1 Quick Start 2
3
Overview 4
3.1 About the TP-107V / TP-120 BoardViewTM Kits 4
3.2 About the TP-107AV / TP-122 Kits 6
3.3 Controlling via the RC-108 and RC-116 Presentation Controllers 7
3.4 Recommendations for Achieving the Best Performance 7
4
Your Line Transmitters and Presentation Controllers 8
4.1 Your TP-107V and TP-107AV Line Transmitters 8
4.2 Your TP-120/TP-122 Line Receiver 10
4.2.1 Your TP-120 XGA Line Receiver 10
4.2.2 Your TP-122 XGA / Audio Line Receiver 12
4.3 Your RC-108 / RC-116 Presentation Controller 13
5
Configuring a TP-107V / TP-107AV System 16
5.1 Connecting the TP-107V / TP-107AV 16
5.2 Configuring the TP-107AV / TP-122 Kit with the RC-108 17
5.2.1 Connecting the RC-108 to the TP-107AV / TP-122 Kit 18
5.3 Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors 19
5.4 Connecting the RS-232 Port 19
5.5 Connecting via the RS-485 20
5.6 Setting the Dipswitches of the TP-107AV 20
6
Flash Memory Upgrade 21
6.1 Downloading from the Internet 21
6.2 Connecting the PC to the RS-232 Port 22
6.3 Upgrading Firmware 22
7
Technical Specifications 27
Figures
Figure 1: TP-107V / TP-120 Kit 5
Figure 2: TP-107V XGA Line Transmitter 8
Figure 3: TP-107AV XGA / Audio Line Transmitter 8
Figure 4: TP-107V / TP-107AV Underside Panel reference 9
Figure 5: TP-120 XGA Line Receiver 10
Figure 6: TP-120 XGA Line Receiver (Underside) 11
Figure 7: TP-122 XGA / Audio Line Receiver 12
Figure 8: TP-122 XGA / Audio Line Receiver (Underside) 13
Figure 9: RC-108 Presentation Controller 13
i
Contents
Figure 10: RC-116 Presentation Controller 14
Figure 11: RC-108 Underside Panel 14
Figure 12: RC-116 Underside Panel 15
Figure 13: Connecting the TP-107AV 17
Figure 14: Configuring the TP-107AV / TP-122 / RC-108 System 18
Figure 15: CAT 5 PINOUT 19
Figure 16: RS-232 PINOUT Connection 19
Figure 17: Wiring the RS-485 Connector 20
Figure 18: Dipswitch Settings 20
Figure 19: Splash Screen 22
Figure 20: Atmel – Flip Window 23
Figure 21: Device Selection Window 23
Figure 22: Device Selection Window 24
Figure 23: Loading the Hex 24
Figure 24: RS-232 Window 25
Figure 25: Atmel – Flip Window (Connected) 25
Figure 26: Atmel – Flip Window (Operation Completed) 26
Tables
Table 1: Board View Package Options 1
Table 2: Adding Units to a System 2
Table 3: TP-107V / TP-107AV (Top Panel) Features 9
Table 4: TP-107V / TP-107AV (Underside Panel) Features 10
Table 5: TP-120 XGA Line Receiver Features 11
Table 6: TP-120 XGA Line Receiver (Underside) Features 11
Table 7: TP-122 XGA / Audio Line Receiver Features 12
Table 8: TP-122 XGA / Audio Line Receiver (Underside) Features 13
Table 9: RC-108/RC-116 Presentation Controller Features 14
Table 10: RC-108 / RC-116 (Underside Panel) Features 15
Table 11: CAT 5 PINOUT 19
Table 12: RS-232 PINOUT Connection 19
Table 13: Dipswitch Setting Features 20
Table 14: Machine Number Settings 21
Table 15: Technical Specifications of the TP-107V 27
Table 16: Technical Specifications of the TP-107AV 27
Table 17: Technical Specifications of the RC-108 / RC-116 27
ii
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Introduction
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast
range of problems that confront the video, audio, presentation, and
broadcasting professional on a daily basis. In recent years, we have
redesigned and upgraded most of our line, making the best even better! Our
1,000-plus different models now appear in 11 groups1 that are clearly defined
by function.
Congratulations on purchasing your Kramer BoardView™ kit, which is ideal
for:
Presentation and multimedia applications
Long range graphics distribution for schools, hospitals, laboratories,
security, and stores
This user manual2 is supplied with each kit (see Table 1) and each individual
unit (see Table 2).
Table 1: Board View Package Options
BroadView
Kit Name
2V
2AV
4V
4AV
8V
8AV
Machines
Included
Two TP-107V
One TP-120
Two TP-107AV
One TP-122
Four TP-107V
One TP-120
Four TP-107AV
One TP-122
Eight TP-107V
One TP-120
Eight TP-107AV
One TP-122
Combined STP
CAT 5 and K-NET3
Cables4 Provided
1 1.25A N/A
1 1.25A N/A
3 2.1A
3 2.1A
7 5A
7 5A
Power Adapter
Provided (12V DC)5
Recommended
Controller
RC-108
RC-108
RC-116
RC-116
You can also purchase additional single units to add to the system, as defined
in Table 2:
1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3 : Control Systems; GROUP 4:
Format/Standards Converters; GROUP 5: Twisted-Pair Solutions; GROUP 6: Specialty AV Products; GROUP 7: Scan
Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories and
Rack Adapters; GROUP 11: Sierra Products
2 Download up-to-date Kramer user manuals from the Internet at this URL: http://www.kramerelectronics.com
3 K-NET is a proprietary Kramer protocol for interconnecting Kramer units
4 See section 1.1
5 Adding additional single units to a kit will probably change the power requirements
1
Getting Started
Table 2: Adding Units to a System
The unit Cables Provided
TP-107V
TP-107AV
RC-108
RC-116
One Combined K-NET and CAT 5 Cable1
One Combined K-NET and CAT 5 Cable1
One K-NET cable
One K-NET cable
1.1 The C-STP+KNET-6 Cable
The C-STP+KNET-6 cable provided with the BoardView kits is a combined
STP CAT 5 and K-NET cable, which can be separated by carefully tearing it
along the cable lines.
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Use Kramer high performance high resolution cables2
2.1 Quick Start
This quick start chart summarizes the basic setup and operation steps.
1 C-STP+KNET-6
2 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
2
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Getting Started
3
Overview
3 Overview
This section describes:
The TP-107V / TP-120 BoardView™ kits, see section 3.1
The TP-107AV / TP-122 BoardView™ kits, see section 3.2
The RC-108 and the RC-116, presentation controllers, see section 3.3
Recommendations for achieving the best performance, see section 3.4
3.1 About the TP-107V / TP-120 BoardViewTM Kits
The TP-107V is an XGA Line Transmitter that accepts a computer graphics1
video signal and transmits it over a CAT 5 cable.
The TP-120 is an XGA Line Receiver2 that receives a coded CAT 5 signal,
decodes it and converts it to an XGA output.
The kits include two, four or eight TP-107V machines that can be
interconnected (via the combined CAT 5 and K-NET cables, supplied with the
kit) and each assigned a priority number3 (in sequence). Pressing an online
button on any of the interconnected machines transmits the signal from that
machine to the TP-120 receiver, which is also connected to the system (see
Figure 1). The signal is then decoded by the TP-120 and converted to an XGA
output. If the ONLINE button is pressed simultaneously on several machines,
the machine with the highest machine number will transmit the signal to the
receiver.
The priorities of a TP-107V / TP-120 system can also be set by the RC-108 or
the RC-116 presentation controllers4 (see section 3.3) that can determine which
machine in the chain will have access to the TP-120.
1 The terminology XGA is used throughout this manual, where this implies any RGBHV signal on a 15-pin HD computer
graphics video connector having a resolution from VGA up to UXGA
2 You can download the Kramer TP-120 user manual at: http://www.kramerelectronics.com
3 A machine number
4 Depending on the number of interconnected units
4
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
TP-12 0
PC
TP-107 V
RC-108
PC
TP-107V
T P-107V
PC
TP-107V
PC
PC
TP-107V
C-STP+KNET-6
XGA
CAT 5
K-NET
PC
TP-107V
TP-107V
PC
TP-107V
PC
Pr oj ector
Figure 1: TP-107V / TP-120 Kit
The TP-107V includes a:
LINE IN CAT 5 connector, that connects to the LINE OUT CAT 5
connector on the previous Line Transmitter
LINE OUT CAT 5 connector, that connects to a receiver (for example, the
TP-120) or to the next Line Transmitter in the chain
CONTROL set of dipswitches
In addition, the TP-107V:
Can be controlled via RS-485
Has a resolution of up to UXGA
Can change the polarity of decoding H and V Sync for video
Can be upgraded via RS-232 and is 12VDC fed
The TP-120:
Has an operating range of more than 300ft. (more than 100 meters)
Includes EQ. and level controls
Has the power connect feature
1 Powering via the CAT 5 cable fro m either the receiver or the trans mitter is good for 100 meters. Above it, both sides should
be fed with power
1
and is 12V DC fed
5
Overview
3.2 About the TP-107AV / TP-122 Kits
The TP-107AV is an XGA / Audio Line Transmitter that accepts a computer
graphics1 video signal and an analog audio signal and transmits them over a
CAT 5 cable.
The TP-122 is an XGA / Audio Line Receiver2 that receives the coded CAT 5
signal transmitted by a TP-107AV, decodes it and converts it to XGA, stereo
analog and S/PDIF digital audio outputs.
The kits can include two, four or eight TP-107AV machines that can be
interconnected (via the combined CAT 5 and K-NET cables, supplied with the
kit) and each assigned a priority number3 (in sequence). Pressing an ONLINE
button on any of the interconnected machines transmits the signal from that
machine to the TP-122 receiver, which is also connected to the system (see
Figure 1)4. The signal is then decoded on the TP-122 and converted to an XGA
output and audio outputs. If the ONLINE button is pressed simultaneously on
several machines, the machine with the highest machine number will transmit
the signal to the receiver.
The priorities of a TP-107AV / TP-122 system can also be set by the RC-108
or the RC-116 presentation controllers5 (see section 3.3) that can determine
which machine in the chain will have access to the TP-122.
The TP-107AV includes a:
LINE IN CAT 5 connector, that connects to the LINE OUT CAT 5
connector on the previous Line Transmitter
LINE OUT CAT 5 connector, that connects to a receiver (for example, the
TP-122) or to the next Line Transmitter in the chain
CONTROL set of dipswitches
In addition, the TP-107AV:
Can be controlled via RS-485
Has a resolution of up to UXGA
Can change the polarity of decoding H and V Sync for video
Can be upgraded via RS-232 and is 12V DC fed
1 The terminology XGA is used throughout this manual, where this implies any RGBHV signal on a 15-pin HD computer
graphics video connector having a resolution from VGA up to UXGA
2 You can download the Kramer TP-122 user manual at: http://www.kramerelectronics.com
3 A machine number
4 Same as the TP-107V / TP-120 kit except for the audio line from the PC to the TP-107AV and speakers that are connected
to the TP-122
5 Depending on the number of interconnected units
6
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
In addition, the TP-122:
Can power or be powered by the transmitter over the same CAT 5 cable
Can change the polarity of decoding H and V Sync for video
Includes EQ. and level controls
Allows an operation range of more than 300ft. (more than 100 meters)
over standard CAT 5 cable
Is 12V DC fed
3.3 Controlling via the RC-108 and RC-116 Presentation Controllers
The RC-108 and RC-116 are presentation controller units designed specifically
to control a system1. Each presentation controller has the appropriate number of
input selector buttons2, an RS-485 and 12V port and an RS-232
9-pin D-sub port for control and firmware upgrade.
3.4 Recommendations for Achieving the Best Performance
Achieving the best performance means:
Connecting only good quality connection cables3, thus avoiding
interference, deterioration in signal quality due to poor matching, and
elevated noise levels (often associated with low quality cables)
Avoiding interference from neighboring electrical appliances that may
adversely influence signal quality, and positioning your Kramer
BoardView Kit away from moisture, excessive sunlight and dust
Caution – No operator-serviceable parts inside unit.
Warning – Use only the Kramer Electronics input power
wall adapter that is provided with this unit4.
Warning – Disconnect power and unplug unit from wall
before installing or removing device or servicing unit.
1 Up to eight and up to 16 units, respectively
2 Eight and 16 buttons, respectively
3 The combined CAT 5 and K-NET cable: C-STP+KNET-6
4 For example: model number AD2512C, part number 2535-000251
7
Your Line Transmitters and Presentation Controllers
4 Your Line Transmitters and Presentation Controllers
This section describes the:
TP-107V and TP-107AV line transmitters (see section 4.1)
TP-120 and TP-122 line receivers (see section 4.2)
RC-108 and RC-116 presentation controllers (see section 4.3)
4.1 Your TP-107V and TP-107AV Line Transmitters
Figure 2 and Figure 3 illustrate the TP-107V and the TP-107AV, respectively.
Table 3 defines the TP-107V / TP-107AV:
Figure 2: TP-107V XGA Line Transmitter
Figure 3: TP-107AV XGA / Audio Line Transmitter
8
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Line Transmitters and Presentation Controllers
Table 3: TP-107V / TP-107AV (Top Panel) Features
# Feature Function
1 CONTROL Dipswitches DIPs 1, 2, 3 and 4 determine the machine number; DIP 8 sets to
2 LINE IN 1 RJ-45 Connector Connects to1 the LINE OUT RJ-45 connector on the previous line
3 LINE OUT 2 RJ-45 Connector Connects to1 the LINE IN RJ-45 connector on the receiver2 or the
4 RS-485 and 12V DC PINs PIN GND is for the Ground connection; PIN B (-) and PIN A (+) are
5 XGA IN 15-pin HD Connector Connects to the XGA source
6 ONLINE Button Press to access priority
7 ON LED Lights when receiving power
8 Audio IN 3.5mm Mini Jack
standalone or slave mode; DIPs 5, 6 and 7 are reserved
transmitter
next line transmitter
for RS-4853 or RS-2324, and PIN +12V is for powering the unit5
Connects to the audio source (applies only to the TP-107AV)
Figure 4 and Table 4 define the underside of the TP-107V / TP-107AV:
Figure 4: TP-107V / TP-107AV Underside Panel reference
1 Using CAT 5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 11 and Figure 15)
2 For example, the Kramer TP-120 or TP-122. You can download this user manual at: http://www.kramerelectronics.com
3 Connects to the RS-232 9-pin D-sub port on a Kramer (or other) device or PC (when both RS-232 underside switches are set
to the left)
4 When both underside RS-232 switches are set to the right
5 The 12V DC power supply (provided) is used to power the system (see Table 1)
9
Your Line Transmitters and Presentation Controllers
Table 4: TP-107V / TP-107AV (Underside Panel) Features
# Feature Function
SYNC POLARITY
1 HS Slide the switch to the left to INV.1 to change the HS polarity2
Switches
2
3 ID BIT Switch Slide to the right to ON3 or to the left to set to OFF
4 RS-232 Switches Set both switches to the right to convert the RS-485 connectors to RS-232
5 RS-485 TERM. Switch
6 PROGRAM Switch Slide to the right to PROGRAM to upgrade to the latest Kramer firmware
Slide the switch to the right to NORMAL to retain the polarity
VS Slide the switch to the left to INV.1 to change the VS polarity2
Slide the switch to the right to NORMAL to retain the polarity
for firmware upgrade
Set the switch to the left to ON for RS-485 Line Termination with 120
(via RS-232), see section 6.
Switch to the left for normal operation
4.2 Your TP-120/TP-122 Line Receiver
This section defines the:
TP-120 XGA Line Receiver (see section 4.2.1)
TP-122 XGA / Audio Line Receiver (see section 4.2.2)
4.2.1 Your TP-120 XGA Line Receiver
Figure 5 and Table 5 define the TP-120 XGA Line Receiver:
Figure 5: TP-120 XGA Line Receiver
1 By default, both switches are set to the right
2 Downgoing syncs
3 The default. Enabling the notebook or laptop to output a VGA signal to an external VGA monitor
10
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Line Transmitters and Presentation Controllers
Table 5: TP-120 XGA Line Receiver Features
# Feature Function
1 LINE IN RJ-45 Connector
2 XGA OUT HD15F Connector Connect to the XGA acceptor
3 12V DC +12V DC connector for powering the unit
4 EQ.1 Trimmer Adjusts2 the cable compensation equalization level
5 LEVEL Trimmer Adjusts2 the output signal level
6 ON LED Illuminates when receiving power
Connects to the LINE OUT RJ-45 connector on the TP-107V
Figure 6 and Table 6 define the underside of the TP-120 XGA Line Receiver:
Figure 6: TP-120 XGA Line Receiver (Underside)
Table 6: TP-120 XGA Line Receiver (Underside) Features
# Feature Function
1 H SYNC Switch Slide the switch down to retain the polarity
2 V SYNC Switch Slide the switch down to retain the polarity
Slide the switch up3 to change the H SYNC polarity
Slide the switch up3 to change the V SYNC polarity
1 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
2 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
3 By default, both switches are set down for normal V SYNC and H SYNC polarity
11
Your Line Transmitters and Presentation Controllers
4.2.2 Your TP-122 XGA / Audio Line Receiver
Figure 7 and Table 7 define the TP-122 XGA / Audio Line Receiver:
Figure 7: TP-122 XGA / Audio Line Receiver
Table 7: TP-122 XGA / Audio Line Receiver Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 S/PDIF RCA connector Connects to the digital audio acceptor
3
4 LINE IN RJ-45 Connector
5 XGA OUT HD15F Connector Connects to the XGA acceptor
6 LINK LED Illuminates when receiving the correct input signal
7 LEVEL Trimmer Adjusts4 the output signal level
8 EQ.3 Trimmer Adjusts4 the cable compensation equalization level
9 ON LED Illuminates when receiving power
ANALOG 3.5mm Mini
OUT
AUDIO
Jack
Connects to the analog audio acceptor
Connects to1 the TP-121 or the TP-1042
1 Using an STP CAT 5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 11 and Figure 15)
2 The TP-104 does not accept the audio signals
3 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
4 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
12
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Line Transmitters and Presentation Controllers
Figure 8 and Table 8 define the underside of the TP-122 XGA / Audio Line
Receiver:
Figure 8: TP-122 XGA / Audio Line Receiver (Underside)
Table 8: TP-122 XGA / Audio Line Receiver (Underside) Features
# Feature Function
1 VS Switch Slide the switch down, to set the V SYNC to negative polarity; slide the switch up1,
2 HS Switch Slide the switch down, to set the H SYNC to negative polarity; slide the switch up1,
to set the V SYNC to positive polarity
to set the H SYNC to positive polarity
4.3 Your RC-108 / RC-116 Presentation Controller
Figure 9 and Table 9 define the RC-108:
Figure 9: RC-108 Presentation Controller
1 By default, both switches are set down (for a negative V SYNC and H SYNC polarity)
13
Your Line Transmitters and Presentation Controllers
Figure 10 and Table 9 define the RC-116:
Figure 10: RC-116 Presentation Controller
Table 9: RC-108/RC-116 Presentation Controller Features
# Feature Function
1 SELECTOR Button1
2 RS-232 9-pin D-sub
Connector
3 RS-485 and 12V DC PINs PIN GND is for the Ground connection; PIN B (-) and PIN A (+) are for
Press to give priority to a TP-107V/TP-107AV unit, according to its
machine number
Press and hold2 to toggle between releasing control3 over the TP-107V
/ TP-107AV and regaining control
Connects to a PC or a Remote Controller, and also for upgrading the
firmware (see section 6)
RS-485, and PIN +12V is for powering the unit
Figure 11, Figure 12 and Table 10 define the underside of the RC-108 and the
RC-116:
Figure 11: RC-108 Underside Panel
1 From 1 to 8 for the RC-108, and from 1 to 16 for the RC-116
2 For about 2 seconds
3 For example, to let unit 6 gain control, press the selector button 6 (button 6 illuminates). To let unit 7 gain control, press the
selector button 7 (button 7 illuminates and button 6 no longer illu minates). To release contr ol over the units, press and hold
the selected button (button 7 in this example) until it no longer illuminates
14
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Line Transmitters and Presentation Controllers
Figure 12: RC-116 Underside Panel
Table 10: RC-108 / RC-116 (Underside Panel) Features
# Feature Function
1 PROGRAM Switch Slide upwards to PROGRAM to upgrade to the latest Kramer firmware
2 RS-485 TERM. Switch
3 NULL MODEM MODE
Switch
(see section 6), slide downwards for normal operation
Set the switch to the left to ON for RS-485 Line Termination with 120
Set to NULL MODEM MODE to connect a PC to the unit, using the Null-
modem adapter; otherwise connect without a null-modem adapter
15
Configuring a TP-107V / TP-107AV System
5 Configuring a TP-107V / TP-107AV System
This section describes how to:
Connect the TP-107V / TP-107AV (see section 5.1)
Configure a TP-107AV / TP-122 kit with an RC-108 / RC-116 controller
(see section 5.2)
Wire the CAT 5 LINE IN / LINE OUT RJ-45 Connectors (see section 5.3)
Connect a PC (see section 5.4)
Connect via the RS-485 terminal block connector (see section 5.5)
Use the dipswitches (see section 5.6)
5.1 Connecting the TP-107V / TP-107AV
To connect the TP-107AV1 as illustrated in the example in Figure 13, do the
following:
1. Connect an XGA source (for example, a computer graphics source) to the
XGA IN 15-pin HD computer graphics connector and an audio source to
the Audio IN 3.5mm mini jack, for example, using a Kramer
C-GMA/GMA cable (VGA HD15M +Audio jack to VGA HD15M
+Audio jack)2.
2. Connect the LINE OUT RJ-45 connector to the LINE IN RJ-45 connector
on the next TP-107AV in the chain or to the LINE IN RJ-45 connector of
a receiver (for example, the Kramer TP-1203 for the TP-107V, or TP-122
for the TP-107AV), via STP cabling4 (with a range of more than 300ft
(>100m)).
3. Connect the LINE OUT RJ-45 connector of the previous TP-107AV unit
to the LINE IN RJ-45 connector on the TP-107AV.
4. Connect the RS-485 and +12V5 port to the previous and the next
TP-107AV unit or to the RC-108 Presentation Controller6.
1 From this section on, the TP-107AV applies also to the TP-107V (except for the audio connection) unless stated otherwise
2 Not supplied. The full list of Kramer cables is on our Web site at http://www.kramerelectronics.com. Alternatively, you can
connect an XGA source to the XGA IN 15-pin HD computer graphics connector, and a separate audio source to the AUDIO
IN 3.5mm mini jack
3 Refer to the separate user manual, which can be downloaded at http://www.kramerelectronics.com
4 For details of how to wire a CAT 5 LINE IN / LINE OUT RJ-45 connector, see section 5.3
5 The 12V DC power supply (provided) is used to power the system (see Table 1)
6 Or alternatively to the RC-116 (see section 3.3)
16
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Configuring a TP-107V / TP-107AV System
Figure 13: Connecting the TP-107AV
5.2 Configuring the TP-107AV / TP-122 Kit with the RC-1081
To configure a presentation system as illustrated in the example in Figure 14,
do the following:
1. Connect the computer graphics source on each TP-107AV2 machine in
the chain (see section 5.1).
2. Interconnect the TP-107AV machines via the C-STP+KNET-6 cables.
3. Connect the RC-108 Presentation Controller to the chain via the RS-485
port.
4. Connect the last TP-107AV unit to a receiver (for example, the Kramer
TP-1223), which is connected to an acceptor (for example, a projector and
an AV receiver with speakers).
5. Set the RS-485 TERM switch on the first unit to ON.
6. Set a machine number for each machine via the dipswitches
(see section 5.6).
1 From this section on, the RC-108 applies also to the RC-116, unless stated otherwise
2 You may connect both types in the same chain
3 Refer to the separate user manual, which can be downloaded at http://www.kramerelectronics.com
17
Configuring a TP-107V / TP-107AV System
Figure 14: Configuring the TP-107AV / TP-122 / RC-108 System
5.2.1 Connecting the RC-108 to the TP-107AV / TP-122 Kit
The RC-108 unit, when connected to a chain of TP-107AV units, controls the
system by granting access to the projector and overriding the individual
ONLINE buttons on the TP-107AV units.
If a SELECTOR button on the RC-108 is pressed and held for about 2
seconds, the RC-108 loses control over the TP-107AV units in the chain. To
regain control, press and hold once again.
18
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Configuring a TP-107V / TP-107AV System
RS-232 PINOUT
Tx
5.3 Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors
Table 11 and Figure 15 define the STP CAT 5 PINOUT, using a straight
pin-to-pin cable with RJ-45 connectors:
Table 11: CAT 5 PINOUT
EIA /TIA 568A EIA /TIA 568B
PIN Wire Color PIN Wire Color
1 Green / White 1 Orange / White
2 Green 2 Orange
3 Orange / White 3 Green / White
4 Blue 4 Blue
5 Blue / White 5 Blue / White
6 Orange 6 Green
7 Brown / White 7 Brown / White
8 Brown 8 Brown
Pair 1 4 and 5 Pair 1 4 and 5
Pair 2 3 and 6 Pair 2 1 and 2
Pair 3 1 and 2 Pair 3 3 and 6
Pair 4 7 and 8
Pair 4 7 and 8
Figure 15: CAT 5 PINOUT
5.4 Connecting the RS-232 Port
The RS-232 9-pin D-sub connector port is defined in Table 12 and Figure 16:
Table 12: RS-232 PINOUT Connection
Connect this PIN on the
Terminal Block Connector:
Tx PIN 2
Rx PIN 3
GND PIN 5
To this PIN on the 9-pin
D-sub Connector
5
9
4
8
3
7
2
6
1
Figure 16: RS-232 PINOUT
Connection
GND
Rx
19
Configuring a TP-107V / TP-107AV System
K-NET (RS-485) PINOUT
OFF
ON
1 2 3 4 5 6 7 8
5.5 Connecting via the RS-485
You can interconnect the TP-107AV units together with an RC-108/RC-116
controller via RS-485 communication (using the C-STP+KNET-6 cables), as
illustrated in Figure 17.
Figure 17: Wiring the RS-485 Connector
5.6 Setting the Dipswitches of the TP-107AV
Figure 18 and Table 13 define the factory default dipswitches:
Figure 18: Dipswitch Settings
Table 13: Dipswitch Setting Features
DIPS Description
1, 2, 3, 4
5, 6, 7 Not used
8 Set to ON for a standalone unit
Set the machine number for each TP-107AV/TP-107V in the chain (see Table 14)
Set to OFF when in slave mode
GND
-
+
+12V
Black
B
A
White
Green
Red
20
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Flash Memory Upgrade
Table 14 defines the Unit number dipswitch setup:
Table 14: Machine Number Settings
Machine # DIP 1 DIP 2 DIP 3 DIP 4 Machine # DIP 1 DIP 2 DIP 3 DIP 4
1 OFF OFF OFF OFF 9 OFF OFF OFF ON
2 ON OFF OFF OFF 10 ON OFF OFF ON
3 OFF ON OFF OFF 11 OFF ON OFF ON
4 ON ON OFF OFF 12 ON ON OFF ON
5 OFF OFF ON OFF 13 OFF OFF ON ON
6 ON OFF ON OFF 14 ON OFF ON ON
7 OFF ON ON OFF 15 OFF ON ON ON
8 ON ON ON OFF 16 ON ON ON ON
6 Flash Memory Upgrade
The TP-107V1 firmware is located in FLASH memory, which lets you
upgrade2 to the latest Kramer firmware version in minutes! The process
involves:
Downloading from the Internet (see section 6.1)
Connecting the PC to the RS-232 port (see section 6.2)
Upgrading Firmware (see section 6.3)
6.1 Downloading from the Internet
You can download the up-to-date file3 from the Internet. To do so:
1. Go to our Web site at www.kramerelectronics.com and download the
file: “FLIP_TP107.zip” from the Technical Support section.
2. Extract the file: “FLIP_ TP107.zip” to a folder (for example, C:\Program
Files\Kramer Flash).
3. Create a shortcut on your desktop to the file: “FLIP.EXE”.
1 This section applies also to TP-107AV, RC-108 and RC-116
2 Upgrade should be carried out by skilled technical personnel. Failure to upgrade correctly will result in the malfunction of
the machine
3 The files indicated in this section are given as an example only. File names are liable to change from time to time
21
Flash Memory Upgrade
6.2 Connecting the PC to the RS-232 Port
Before installing the latest Kramer firmware version on a TP-107V unit, do
the following:
1. Connect the RS-232 9-pin D-sub rear panel port according to section 5.4.
2. Slide the underside PROGRAM switch to ON).
3. Switch the unit ON.
6.3 Upgrading Firmware
Follow these steps to upgrade the firmware:
1. Double click the desktop icon: “Shortcut to FLIP.EXE”.
The Splash screen appears as follows:
Figure 19: Splash Screen
2. After a few seconds, the Splash screen is replaced by the “Atmel – Flip”
window:
22
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Flash Memory Upgrade
Figure 20: Atmel – Flip Window
3. Press the keyboard shortcut key F2 (or select the “Select” command from
the Device menu, or press the integrated circuit icon in the upper right
corner of the window).
The “Device Selection” window appears:
Figure 21: Device Selection Window
4. Click the button next to the name of the device and select from the list:
AT89C51RD2:
23
Flash Memory Upgrade
AT89C51RD 2
T89C5 1RD2
Figure 22: Device Selection Window
5. Click OK and select “Load Hex” from the File menu.
24
Figure 23: Loading the Hex
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Flash Memory Upgrade
6. The Open File window opens. Select the correct HEX file that contains
the updated version of the firmware for TP-107V (for example
44M_V1p2.hex) and click Open.
7. Press the keyboard shortcut key F3 (or select the “Communication /
RS232” command from the Settings menu, or press the keys: Alt SCR).
The “RS232” window appears. Change the COM port according to the
configuration of your computer and select the 9600 baud rate:
Figure 24: RS-232 Window
8. Click Connect.
In the “Atmel – Flip” window, in the Operations Flow column, the Run
button is active, and the name of the chip appears as the name of the third
column: AT89C51RD2.
Verify that in the Buffer Information column, the “HEX File: TP107.hex”
appears.
TP107.hex
Figure 25: Atmel – Flip Window (Connected)
9. Click Run.
After each stage of the operation is completed, the check-box for that
25
Flash Memory Upgrade
stage becomes colored green1.
When the operation is completed, all 4 check-boxes will be colored green
and the status bar message: Memory Verify Pass appears2:
TP107.hex
Figure 26: Atmel – Flip Window (Operation Completed)
10. Close the “Atmel – Flip” window.
11. Disconnect the power on the TP-107V.
12. If required, disconnect the RS-232 rear panel port on the TP-107V unit
from the Null-modem adapter.
13. Slide the underside PROGRAM switch to the normal position.
14. Connect the power to the TP-107V.
1 See also the blue progress indicator on the status bar
2 If an error message: “Not Finished” shows, click Run again
26
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications
7 Technical Specifications1
Table 15, Table 16 and Table 17 define the TP-107V / TP-107AV / RC-108 /
RC-116 technical specifications.
Table 15: Technical Specifications of the TP-107V
INPUT: 1 XGA on a 15-pin HD connector, 1 CAT 5 on an RJ-45 connector (LINE IN)
OUTPUTS: 1 CAT 5 on an RJ-45 connector (LINE OUT)
MAX. OUTPUT LEVEL: 1.5Vpp
HIGHEST RESOLUTION: UXGA, 1080p
S/N RATIO: 61dB @5MHz
CONTROLS: Slide switches BIT: ID BIT (PIN 4); horizontal and vertical sync inversion;
COUPLING: AC
POWER SOURCE: See Table 1
DIMENSIONS: 12cm x 6.95cm x 2.44cm (4.7" x 2.74" x 0.96"), W, D, H
WEIGHT: 0.3kg (0.66lbs) approx.
ACCESSORIES: Power supply, mounting bracket, 19” rack adapters,
INPUTS: 1 XGA on a 15-pin HD connector, 1 CAT 5 on an RJ-45 connector (LINE IN)
OUTPUTS: 1 CAT 5 on an RJ-45 connector (LINE OUT)
MAX. OUTPUT LEVEL: VIDEO: 1.5Vpp AUDIO: 1.7Vpp
BANDWIDTH (-3dB): AUDIO: 21kHz
S/N RATIO: VIDEO: 61dB @5MHz AUDIO: 78dB
CROSSTALK (all hostile): VIDEO: -55.5dB @50MHz, video into audio
CONTROLS: Slide switches bit: ID BIT (PIN 4), horizontal and vertical sync inversion;
COUPLING: VIDEO: AC AUDIO: AC
AUDIO THD + NOISE: 0.1%
AUDIO 2nd HARMONIC: 0.02%
POWER SOURCE: See Table 1
DIMENSIONS: 12cm x 6.95cm x 2.44cm (4.7" x 2.74" x 0.96"), W, D, H
WEIGHT: 0.3kg (0.66lbs) approx.
ACCESSORIES: Power supply, mounting bracket, 19” rack adapters,
Table 17: Technical Specifications of the RC-108 / RC-116
CONTROLS: RS-485, RS-232
DIMENSIONS:
WEIGHT:
RS-232, RS-485, RS-485 TERM, PROGRAM
Combined K-NET and CAT 52 cables (see Table 1)
Table 16: Technical Specifications of the TP-107AV
1 stereo on 3.5mm phones
RS-232, RS-485, RS-485 TERM, PROGRAM
K-NET and CAT 5 cables (see Table 1)
RC-108: 12cm x 6.95cm x 2.44cm (4.7" x 2.74" x 0.96"), W, D, H
RC-116: 18.4cm x 11.4cm x 2.65cm (7.24" x 4.5" x 1.05"), W, D, H
RC-108: 0.3kg (0.66lbs) approx.
RC-116: 0.6kg (1.32lbs) approx.
1 Specifications are subject to change without notice
2 C-STP+KNET-6
27
LIMITED WA RRANTY
Kramer Electronics (hereafter ) warrants this product free from defects in material and workmanship under the
following terms.
HOW LONG IS THE WA RRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
WHO IS PROTECTED?
Only the first purchase customer may enforce this warranty.
WHAT I S COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in materia l or workmansh ip in this product. The following are not covered
by the w arranty :
1. Any product which is not distributed by Kramer, or which is not p urchased from an authorized Kramer dealer. If you are
uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the Web site
www.kramerelectronics.com.
2. Any product, on which the serial number has been defaced, modified or removed, or on which the WARRANTY VOID
TAMPERED sticker has been torn,
IF reattached, removed or otherwise interfered with.
3. Damage, deterioration or malfunction resulting from:
i) Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
ii) Product modification, or failure to follow instructions supplied with t he product
iii) Repair or attempted repair by anyone not authorized by Kramer
iv) Any shipment of the product (claims must be presented to the carrier)
v) Removal or installation of the product
vi) Any other cause, which does not relate to a product defect
vii) Cartons, equipment enclosures, cables o r accessories used in c onjunction with the product
WHAT WE WILL PAY FOR AND WHAT W E WI LL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1. Removal or i nstallations charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the
responsibility of the Kramer dealer from whom the product was purchased.
3. Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty
coverage, and should be included in any shipment of the product. Please also include in any mailing a contact name,
company, address, and a description of the problem(s).
3. For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WA RRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to
the length of this warranty.
EXCLUSION OF DAMAGES
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall
not be liable for:
1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of t he product, l oss
of time, commercial loss; or:
2. Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
NOTE:
This equipment has been tested to determine compliance with the requirements of:
EN-50081: "Electromagnetic compatibility (EMC);
Residential, commercial and light industry"
EN-50082: "Electromagnetic compatibility (EMC) generic immunity standard.
CFR-47: FCC Rules and Regulations:
CAUTI ON!
generic emission standard.
Part 1:
Part 1: Residential, commercial and light industry environment".
Part 15: “Radio frequency devices
Subpart B Unintentional radiators”
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or
modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the
equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.
Kramer
28
KRAMER: SIMPLE CREATIVE TECHNOLOGY
For the latest information on our products and a list of Kramer
distributors, visit our Web site: www.kramerelectronics.com,
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
Caution
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900-000282 REV 2
Loading...