Kramer Electronics, Ltd.
USER MANUAL
Model:
RC-8IR
Universal Room Controller
Contents
Contents
1 Introduction 1
2 Getting Started 1
3 Overview 2
4 Your Universal Room Controller 3
5 Installing the RC-8IR Universal Room Controller 5
5.1 Setting the Labels and Button Caps 6
5.2 Mounting the Device Housing 7
5.3 Mounting the RC-8IR Faceplate 7
6 Using the RC-8IR Universal Room Controller 8
6.1 Operating the RC-8IR 10
6.2 An Example of Operating the RC-8IR 11
6.3 Using the Macro Buttons 12
6.4 Locking the Front Panel 12
6.5 Turning the Light of the Backlit Buttons On and Off 12
6.6 Using the Internal Web Page 12
7 Flash Memory Upgrade 13
7.1 Downloading from the Internet 13
7.2 Connecting the PC to the RS-232 Port 14
7.3 Upgrading Firmware 14
7.4 Installing the Web Applet 15
8 Technical Specifications 15
Figures
Figure 1: RC-8IR Front Panel 3
Figure 2: RC-8IR Right Side Panel 4
Figure 3: RC-8IR Rear Panel 5
Figure 4: Button Cap Orientation 6
Figure 5: Placing the Button Cap 6
Figure 6: Mounting the Device Housing 7
Figure 7: Mounting the Faceplate 7
Figure 8: Example of a Typical RC-8IR Configuration 8
Figure 9: Example of a Typical RC-8IR Setup in the Lecture Auditorium 9
Figure 10: RC-8IR Labels Setup 10
Figure 11: RC-8IR Operation Example 11
Figure 12: Internal Web Page Front Panel 13
Figure 13: The KFR-Programmer Window 14
i
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Contents
ii
Tables
Table 1: RC-8IR Front Panel Features 3
Table 2: RC-8IR Right Side Panel Features 4
Table 3: RC-8IR and Rear Panel Features 5
Table 4: Connection Scheme (for the example in Figure 8) 9
Table 5: The Commands Configuration 10
Table 6: Technical Specifications of the RC-8IR Universal Room Controller 15
Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast
range of problems that confront the video, audio, presentation, and
broadcasting professional on a daily basis. In recent years, we have redesigned
and upgraded most of our line, making the best even better! Our 1,000-plus
different models now appear in 11 groups
1
that are clearly defined by function.
Congratulations on purchasing your Kramer RC-8IR Universal Room
Controller, which is designed to let an instructor enter a multimedia
classroom and operate an A/V system with ease.
The package includes the following items:
• RC-8IR device housing and separate faceplate
• One 3.5mm to IR emitter control cable
2
• This user manual
• Configuration software
2 Getting Started
This user manual is written for the end user. Refer to the separate online
RC Configuration and Installation Guide for details of how to install and
configure the Universal Room Controller
3
We recommend that you:
• Review the contents of this user manual
4
• Use Kramer high performance high resolution cables
1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Matrix Switchers; GROUP 3: Control Systems; GROUP 4:
Format/Standards Converters; GROUP 5: Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories
and Rack Adapters; GROUP 11: Sierra Products
2 Download up-to-date Kramer user manuals from the Internet at this URL: http://www.kramerelectronics.com
3 That provides information about how to set up the syste m. This online guide may well be updated on a regular basis. For
the latest online guide, go to http://www.kramerelectronics.com
4 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
Overview
2
3 Overview
Kramer’s RC-8IR one-gang wall plate is a highly versatile controller
interface that acts as an all-in-one extended remote control panel for control
of A/V equipment—especially projectors and associated equipment—in any
room (such as classrooms, boardrooms, or auditoriums). It streamlines
operations and simplifies control by integrating audio, video, and computervideo sources into a centralized system.
The RC-8IR includes:
1
• An Ethernet port for configuration and control
• Configurable backlit buttons
2
to set up any supported
3
command
• Two bidirectional RS-232 wired serial ports, for universal display (for
example, projectors) and switcher control, and one RS-485 serial port
• Two relays for the simplified and centralized control of room functions
(such as lighting, closing blinds, screen settings, and so on)
• Two IR control ports
• An IR-learner for the customized control of external sources, receiving the
IR commands from different remote transmitters without the need for an
external IR remote control unit
• Macro mode operation, for programming up to 15 commands with the
press of a single button, and summing up to a total of 120 commands
• Support for firmware upgrade
To achieve the best performance:
• Connect only good quality connection cables, thus avoiding interference,
deterioration in signal quality due to poor matching, and elevated noiselevels (often associated with low quality cables)
• Avoid interference from neighboring electrical appliances and position
your Kramer RC-8IR away from moisture, excessive sunlight and dust
1 Of up to five machines with unique IP addresses
2 Six buttons for RC-6IR, and eight buttons for the RC-8IR
3 To be configured by the system integrator only
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your Universal Room Controller
3
Front Panel with Faceplate
Front Panel without Faceplate
#
Feature
Function
4 Your Universal Room Controller
Figure 1 and Table 2 define the RC-8IR front panel:
Figure 1: RC-8IR Front Panel
Table 1: RC-8IR Front Panel Features
1 Faceplate Attachment Holes Use to attach the faceplate to the device housing (see Table 2)
2 IR IN Receiver Accepts IR remote commands (for the IR-learner feature)
3 Configurable Control
Buttons (Macro Buttons)
4 Housing Attachment Holes Use to install the device housing
5 Button Caps Button caps with “wings” on the left and right sides (8)
Control the room and the A/V equipment (from 1 to 8)
Your Universal Room Controller
4
Front Panel
Buttons
#
Feature
Function
Figure 2 and Table 2 define the RC-8IR right side panel:
Figure 2: RC-8IR Right Side Panel
Table 2: RC-8IR Right Side Panel Features
1 Housing and Faceplate Support Device housing supports the faceplate
2 RELAY2
3 RELAY1
4 RS-485 Terminal Block
Connector
5 RS-232 Terminal Block
Connector (1 and 2)
6 IR OUT1 PIN
GND PIN Connect to an IR emitter cable
IR OUT2 PIN
7 GND PIN Connects (-) to the Ground
8 +12VDC IN PIN Connects (+) to the connector for powering the unit
1 See the examples in Figure 4
Connect each rela y to a room item (such as lighting, screen
settings, blinds, and so on)
Connect to the RS-485 detachable terminal block on a switcher
or PC
Connect to the RS-232 connector on the A/V equipment or a PC or
other Serial Controller
1
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Installing the RC-8IR Universal Room Controller
5
#
Feature
Function
Figure 3 and Table 3 define the RC-8IR rear panel:
Figure 3: RC-8IR Rear Panel
Table 3: RC-8IR and Rear Panel Features
1 N.U Switch Not used
2 PROGRAM Switch Switch to OFF for normal operation;
3 RS-485 TERM. Switc h Switch to ON for RS-485 line termination
4 FACTORY DEFAULT Button Press to return to the factory default settings, including all the
5 Ethernet Port Connects to a PC or other controller through computer networking
6 Grounding Screw Connect to grounding wire
Switch to ON for firmware upgrade
configured buttons and the network settings
1
5 Installing the RC-8IR Universal Room Controller
This section describes the installation of the RC-8IR and includes:
• Setting up the labels on the buttons, according to your specific
requirements
2
• Mounting the RC-8IR device to the wall
• Installing the button caps
• Mounting the faceplate
• Setting of the device
1 Including the factory default IP number: 192.168.1.39 (an IP number is a device's numerical address as expressed in the
format specified in the Internet Protocol)
2 It is recommended to place labels before mounting the faceplate
Installing the RC-8IR Universal Room Controller
6
5.1 Setting the Labels and Button Caps
To install the labels and button caps:
1. Remove the required labels from the supplied button label sheet.
2. Hold the button cap so that it is oriented as shown in
“wings” on the left and right sides, and insert the label inside the cap.
Figure 4 with the
Figure 4: Button Cap Orientation
3. Repeat for all eight caps.
4. Retaining the orientation, place the eight button caps on the buttons of
the RC-8IR (see
Figure 5).
Figure 5: Placing the Button Cap
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Installing the RC-8IR Universal Room Controller
7
5.2 Mounting the Device Housing
The device housing is mounted to the wall via the two housing mounting
screws holes, as illustrated in Figure 6
:
Figure 6: Mounting the Device Housing
5.3 Mounting the RC-8IR Faceplate
1. Place the faceplate on the RC-8IR so that the two screw mounting holes
are aligned (see
Figure 7).
2. Insert the two mounting screws and tighten with a screwdriver.
Figure 7: Mounting the Faceplate
Using the RC-8IR Universal Room Controller
8
6 Using the RC-8IR Universal Room Controller
Connecting the inputs and the display Configuration via the Windows®based configuration software and/or the IR learner
Configuration guide. The cable installation process is not detailed in this user
2
manual
1
is described in the RC
The universal room controller is very easy to use, as the example in . Figure 8
Table 4 defines3:
and
Figure 8: Example of a Typical RC-8IR Configuration
1 By authorized Kramer technical personnel or by an external system integrator
2 Refer to the separate online “RC Configuration and Installation Guide” at http://www.kramerelectronics.com
3 Your RC-8IR was installed and configured to suit your specific requirements. This example describes how to setup one of
an unlimited number of available setups for the system
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Using the RC-8IR Universal Room Controller
9
This connector:
Controls:
1
2
VCR
DVD
Amplifier
Table 4: Connection Scheme (for the example in Figure 8)
RELAY2 The lights
RELAY1 The screen
RS-485 Terminal Block Connector A power amplifier (and speakers)
RS-232 (TX1, RX1) Terminal Block Connector A projector
IR OUT1 PIN
IR OUT2 PIN2 A video player
Ethernet The RC-8IR via a remote control PC
A laptop is connected to the projector
A DVD player
Figure 9 shows the RC-8IR built into a podium that is located in a lecture
auditorium. An overhead projector and screen, speakers, lights; and a cabinet
with a VCR, a DVD and an amplifier inside, are all controlled via the
RC-8IR. The presenter’s laptop is located on the podium, next to where the
RC-8IR is mounted. It is also controlled by the RC-8IR and is used for
presentations, slide shows and so on.
Figure 9: Example of a Typical RC-8IR Setup in the Lecture Auditorium
1 The second RS-232 port can be used to control another A/V unit or an LCD
2 Connected via the IR emitter cable. IR OUT1 and IR OUT2 can each be connected to identical machines and still be
controlled separately
Using the RC-8IR Universal Room Controller
10
The Label
The Macro Sequence
ON
OFF
DVD
PC
VCR
Vol
UP
Vol
DOWN
HELP
DESK
6.1 Operating the RC-8IR
In the following example
labeled with specific functions and each button is programmed
several tasks
3
1
Table 5 as defined in .
Figure 10 that is illustrated in , the RC-8IR is
Each button may be assigned with up to 15 commands.
Table 5: The Commands Configuration
2
to perform
Figure 10: RC-8IR Labels
Setup
ON
OFF
DVD
VCR
PC
Vol UP
Vol DOWN
HELP DESK
• Power up the projector
• Power up the power amplifier
• Power up the DVD player
• Power up the video player
• Roll down the projector screen
• Turn on the speakers
• 1 minute delay [for the
projector to heat up]
• Turn lights off
• The projector selects the PC input
• Turn lights on
• Power down the projector
• Power down the power amplifier
• Stop the DVD player
• Power down the DVD player
• Stop the video player
• Power down the video player
• Roll up the projector screen
• Turn off the speakers
• Stop the video player
• The projector selects the DVD input
• Play the DVD
• Stop the DVD
• The projector selects the VCR input
• Play the VCR
• Stop the DVD
• Stop the VCR
• The projector selects a PC input
• Power amplifier volume up
• Power amplifier volume down
• Call for technical assistance
1 This is only one example among numerous possibilities, each button can be configured as required
2 By the system integrator
3 A macro sequence, including up to 15 commands per button, carried out one after the other
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Using the RC-8IR Universal Room Controller
11
6.2 An Example of Operating the RC-8IR
Figure 11 shows an operating example:
Figure 11: RC-8IR Operation Example
Using the RC-8IR Universal Room Controller
12
6.3 Using the Macro Buttons
1
Pressing any button initiates a macro sequence
, during which the button
blinks (as programmed by the system integrator).
If during the macro sequence the button blinks faster than usual
that a malfunction has been detected
3
and the RC-8IR exits the macro sequence.
2
, this indicates
To solve the problem, summon technical help
4
If you want to stop a macro sequence, press and hold that button for 5
seconds. The sequence will come to an end. You can resume operation by
pressing any of the buttons
5
. The unit will carry out the macro sequence
commands from the beginning.
6.4 Locking the Front Panel
The front panel can be locked to avoid unintended tampering with the buttons.
To lock the panel, press and hold buttons 4 and 8 simultaneously for about 2
seconds.
All the buttons blink momentarily and the panel is locked. When pressing a
button at this stage, all the buttons blink twice.
To unlock the panel buttons, press the respective buttons once again. All the
buttons blink momentarily and unlock. You can now use the buttons as usual.
6.5 Turning the Light of the Backlit Buttons On and Off
When the room is darkened, the buttons can be illuminated for convenience.
To turn on the backlight, press buttons 3 and 7 simultaneously.
To turn off the backlight, press the respective buttons once again.
6.6 Using the Internal Web Page
The internal Web page can be used to remotely operate the RC-8IR via the
Ethernet.
To control your RC-8IR via the internal Web page, do the following:
1 The macro sequence can be carried out instantly or can ta ke a while, depend ing on the delay ti mes included in the sequence
2 Six times per second, as compared with twice per second during normal operation
3 For example, a faulty DVD player
4 In this example, press the HELP DESK button
5 Including the button you kept pressed to stop the macro sequence
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Flash Memory Upgrade
13
1. Type the unit’s IP number
1
in the Address bar of your browser (or type
any link defined by the system integrator).
The RC-8IR front panel is displayed on your screen (see ).
2. Press the on-screen buttons to control the unit.
Figure 12: Internal Web Page Front Panel
7 Flash Memory Upgrade
The RC device firmware is located in FLASH memory, which lets you
upgrade to the latest Kramer firmware version in minutes!
The process involves:
• Downloading the upgrade package from the Internet (see section
• Connecting the PC to the RS-232 port (see section
• Upgrading the firmware (see section
• Installing the Web Applet (see section
7.3)
7.4)
7.2)
Figure 12
7.1)
7.1 Downloading from the Internet
You can download the up-to-date file
2
from the Internet. To do so:
1. Go to our Web site at http://www.Kramerelectronics.com and download the
file: “SetKFRXXX-xx.zip”
2. Extract the file “SetKFRXXX-xx.zip”
from the technical support section.
package, which includes the
KFR-Programmer application setup, the .s19 firmware file and the Web
Applet dat file, to a folder (for example, C:\Program Files\KFR Upgrade).
3. Install the KFR-Programmer Application.
1 The default IP number is 192.168.1.39, and may be changed by the system integrator
2 File names are liable to change from time to time
Flash Memory Upgrade
14
7.2 Connecting the PC to the RS-232 Port
Before installing the latest Kramer Ethernet firmware version on the
RC-8IR, do the following:
1. Connect the RS-232 port (COM 1) on the RC-8IR to a Null-modem
adapter and connect the Null-modem adapter with a 9-wire flat cable to
the RS-232 9-pin D-sub COM port on your PC.
2. Set the PROGRAM switch to ON.
3. Connect the power on your machine.
7.3 Upgrading Firmware
Follow these steps to upgrade the firmware:
1. Double-click the KFR-Programmer desktop icon.
The KFR-Programmer window appears.
Figure 13: The KFR-Programmer Window
2. Select the required COM Port
1
.
3. Click the File button to select the .s19 firmware file included in the package.
4. Click the Send button to download the file. The Send button lights red.
5. Wait until downloading is completed and the red Send button turns off.
6. Disconnect the power on the RC-8IR.
7. Set the PROGRAM switch to OFF.
8. Connect the power on the RC-8IR.
1 To which the RC device is connected on your PC
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications
15
7.4 Installing the Web Applet
Follow these steps to install the Web Applet
1
:
1. Connect RC-8IR to your PC through computer networking.
2. Start the RC Configuration Software and connect to the RC device (see
the RC Configuration and Installation Guide
2
).
3. In the Device menu select Upgrade Applet option and browse to MC.dat
file included in the package.
4. Wait until uploading is completed and the success message appears.
Click OK.
8 Technical Specifications
Table 6 defines the technical specifications:
Table 6: Technical Specifications
PORTS:
OUTPUTS: 2 relays on terminal block connectors (36V AC or DC, 2A, 60VAC maximum on
POWER SOURCE: 12V DC, 155mA
DIMENSIONS: 11.4cm x 3.7cm x 6.9cm (4.49" x 1.45" x 2.72", W, D, H)
WEIGHT: 0.3kg (0.67lbs) approx
ACCESSORIES: Kramer 3.5mm to IR Emitter Control Cable (C-A35/IRE-10), power supply, two
OPTIONS: Kramer 3.5mm to IR Emitter Control Cable (C-A35/IRE-10), 15 meter and 20 meter
2 RS-232 on terminal block connectors
1 RS-485 on a terminal block connector
1 ETHERNET RJ-45 port
non-inductive load)
2 IR emitters on terminal block connectors
extra M3x5 screws, Java based control software (internal), W indows®-based
Kramer control software
IR emitter extension cables
3
of the RC-8IR Universal Room Controller
1 This section is applicable only to firmware version 26.0 and higher and requires RC Configuration Software version
1.26.0.38 and higher
2 On our Web site at http://www.kramerelectronics.com
3 Specifications are subject to change without notice
KRAMER: SIMPLE CREATIVE TECHNOLOGY
16
LIMITED WARRANTY
WHO IS PROTECTED?
WHAT IS COVERED AND WHAT IS NOT COVERED
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
HOW YOU CAN GET WARRANTY SERVICE
LIMITATION OF IMPLIED WARRANTIES
EXCLUSION OF DAMAGES
CAUTION!
Kramer Electronics (hereafter ) warrants this product free from defects in material and workmanship under the
follow ing terms.
Kramer
HOW LONG IS THE WARRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
Only the first purchase customer may enforce this warranty.
We will pay labor and material expenses for covered items. We will not pay for the following:
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall
not be liable for:
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
This equipment has been tested to determine compliance with the requirements of:
EN-50081: "Electromagnetic compatibility (EMC);
generic emission standard.
Residential, commercial and light industry"
EN-50082: "Electromagnetic compatibility (EMC) generic immunity standard.
Part 1: Residential, commercial and light industry environment".
CFR-47: FCC* Rules and Regulations:
Part 15: “Radio frequency devices
Subpart B Unintentional radiators”
Except as below, this warranty covers all defects in material or w orkmanship in this produc t. The following are not cove red
by the warranty:
1. Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are
uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the Web site
www.kramerelectronics.com.
2. Any product, on which the serial number has been defaced, modified or removed, or on which the WARRANTY VOID
TAMPERED sticker has been torn,
3. Damage, deterioration or malfunction resulting from:
i) Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
ii) Product modification, or failure to follow instructions supplied with the product
iii) Repair or attempted repair by anyone not authorized by Kramer
iv) Any shipment of the product (claims must be presented to the carrier)
v) Removal or installation of the product
vi) Any other cause, which does not relate to a product defect
vii) Cartons, equipment enclosures, cables or accessories used in conjunction with the product
1. Removal or installations charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the
responsibility of the Kramer dealer from whom the product was purchased.
3. Shipping charges.
1. To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty
coverage, and should be included in any shipment of the product. Please also include in any mailing a contact name,
company, address, and a description of the problem(s).
3. For the name of the nearest Kramer authorized service center, consult your authorized dealer.
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to
the length of this warranty.
1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss
of time, commercial loss; or:
2. Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or
modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the
equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.
IF reattached, removed or otherwise interfered with.
* FCC and CE approved using STP cable (for twisted pair products)
NOTE:
Part 1:
For the latest information on our products and a list of Kramer
distributors, visit our Web site: www.kramerelectronics.com,
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
Caution
P/N:
2900- 000695
Rev:
1
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900- REV 1
Loading...