Kramer Electronics Galil 6-I User Manual

The Kramer SPK-W613 In-Wall Speakers

Thank you for purchasing the Kramer

SPK-W613 In-Wall Speakers (rectangular) that

are ideal for multimedia and boardroom

applications.

The SPK-W613 includes a pair of high

performance speakers that can be mounted in

the wall vertically or horizontally.

Installing the Open Back Speakers

To install the speakers, do the following:

1. Remove the grille over the speakers by inserting a paper clip into one of the grille openings
and pulling it upward.

2. Position the mounting tabs (see Figure 1) inward.

Choosing the Best Location

Ideally, locate the speakers in the main listening area. Before doing so, be sure that the:

• Desired location is free of obstructions, such as electrical piping, AC ducts or water lines,

and so on

• Thickness of the mounting surface is between 0.375" and 1.25", and that there is at least a

space of 2.75" behind the mounting surface for open back speakers

• Rear side of the speaker is not blocked by wall studs or other objects

Cutting the Tile

To cut the tile, do the following:

1. Remove the circle/rectangle in the supplied cardboard template.

Keep this piece of cardboard for later use as a mask, as you may want to paint the speakers

2. Mark the opening in the correct location by tracing it on the wall.

3. Cut out the opening according to the template or with a circular cutter set to the appropriate
cutout size.

Initially, you can cut a smaller area inside the marked hole just to be sure that the space above the
speakers is clear

4. Route the wiring from the amplifier to the speakers’ cutout holes, taking care not to place
them next to electrical wires or at least at a distance of about two feet from an AC line.

Do not nail or staple the speakers' wires

For reinforcing the speakers, you can use the Kramer SKIC mounting kit

See the separate user manual on our Web site at http://www.kramerelectronics.com

Figure 1: Position the Mounting Tabs

3. Insert the supplied screws into the screw openings from the front of the speakers.

4. Connect the speaker wires (we recommend that you use our Kramer BC-2S cables) to the

speaker terminals.

5. Insert the speaker into the opening and tighten the screws.
When tightening the screws, the tabs automatically turn outward, thus clamping the
speaker to the wall from its rear side.
Note: Do not over-tighten the screws. This may cause damage to both the speakers and
the surface.

6. Push the grille firmly into the slot in the speaker baffle.

Specifications

SYSTEM DESCRIPTION: 2-way component speaker
HIGH FREQUENCY DRIVER: 1" ferrofluid cooled
LOW FREQUENCY DRIVER: 6.5" Polypropylene cone woofer

IMPEDANCE:

SENSITIVITY (1 Watt, 1 Meter): 89dB
FREQUENCY RESPONSE: 30Hz to 20kHz
POWER RATING: 80W nominal, 120W Max
RECOMMENDED AMPLIFIER POWER: 80 Watts

WEIGHT PER SINGLE SPEAKER: 1.6kg (3.5lbs) approx.
SHIPPING WEIGHT (FOR PAIR): 3.8kg (8.4lbs) approx.
DIMENSIONS: 30.5cm x 21.6cm (12” x 8.5”)
CUTOUT SIZE: 27.3cm x 18.54cm (10.75” x 7.3”)
OPTIONS:

Specifications are subject to change without notice at http://www.kramerelectronics.com

8Ω

Kramer SKIC mounting kit

LIMITED WARRANTY

WHO IS PROTECTED?

WHAT IS COVERED AND WHAT IS NOT COVERED

WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR

HOW YOU CAN GET WARRANTY SERVICE

LIMITATION OF IMPLIED WARRANTIES

EXCLUSION OF DAMAGES

CAUTION !

We w arrant this product free from def ects in material and workmanship u nder the following terms.

HOW LONG IS THE WARRANTY

Labor and parts are warranted for one year from the date of the first customer purchase.

Only the first purchase customer may enforce th is warranty.

We will pay labor and material expenses for covered items. We will not pay for the following:

The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer
shall not be liable for:

This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.

: All products returned to Kram er for service must have prior approval. This may be obtained from your dealer.

This equipment has been tested to determine compliance with the requirements of:

EN-50081: "Electromagnetic comp atibility (EMC);

generic emission standard.
Residential, commercial and light industry"
EN-50082: "Electromagnetic compatibility (EMC) generic immunity standard.

Part 1: Residential, c ommercial and light industry environment".
CFR-47: FCC* Rules and Regulations:

Part 15: “Radio fr equency devices

Subpart B Unintention al radiators”

Except as below, this warranty covers all defects in material or workmanship in this product. The following are not
covered by the warranty:

1. Any product which is not distributed by us or which is not purchased from an authorized Kramer dealer. If you are

uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the Web site
www.kramerelectronics.com.

2. Any product, on which the serial number has been defaced, modified or removed, or on which the WARRANTY VOID

TAMPERED sticker has been torn,

3. Damage, deteriora tion or malfunction resulting f rom:

i) Accident, mis use, abuse, neglect, fire, water, lightning o r other acts of nature
ii) P roduct modification, or failure to follow instructions supplied with the product
iii) Repair or attempted repair by anyone not authorized by Kramer
iv) Any shipment of the produ ct (claims must be presented t o the carrier)
v) Removal or in stallation of the product
vi) Any other cause, which does not relate to a product def ect
vii) Cartons, equipment enc losures, cables or accessories us ed in conjunction with the p roduct

1. Removal or installations charges.

2. Costs of initial technical adjustment s (set-up), including adjustment of user controls or program ming. These costs are

the responsibility of t he Kramer dealer from whom the product was purchased.

3. Shipping charges.

1. To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.

2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of

warranty coverage, and should be included in any shipment of the product. Please also include in any mailing a
contact name, company, address, and a description of the problem(s).

3. For the name of the nearest Kr amer authorized service center, consult your authorized dealer.

All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration
to the length of this warranty.

1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the

product, loss of time, commercial loss; or:

2. Any other damages, w hether incidental, consequential or otherwise. Some countries may not allow limitations on

how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.

Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or
modifications to the unit without the expressed approval of the man ufacturer will void user authority to operate the
equipment.

Use the supplied DC power supply to feed power to the machine.
Please use recommend ed interconnection cables to connec t the machine to other c omponents.

IF reattached, removed or otherwise interfered with.

* FCC and CE a pproved using STP ca ble (for twisted pair products)

NOTE

Part 1:

!

SAFETY WARNING

Disconnect the unit from the power
supply before opening and servicing

KRAMER ELECTRONICS LTD.

User Manual

MODEL:

SPK-W613

In-Wall Speakers

For the latest information on our products and a list of Kramer
distributors, visit our Web site where updates to this user manual may be
found.

We welcome your questions, comments, and feedback.

Web site:
E-mail:

www.kramerelectronics.com

[e-mail]

P/N: 2900-300118 Rev 1