The Kramer WP-301xl Wall Plate
Destination England and the
Belgium and Germany)
Congratulations on purchasing your Kramer WP-301xl Wall Plate which is ideal for
boardrooms and presentation rooms.
The WP-301xl is a single-gang wall plate insert. EDID information can be stored in the
wall plate by using the FC-200 XGA EDID Copier Kramer Tool (see the FC-200 XGA
EDID Copier User Manual). The WP-301xl is supplied with a power supply.
WP-301xl Wall Plate US Version
Figure 1 and Table 1 define the US version of the WP-301xl Wall Plate.
Figure 1: WP-301xl Wall Plate US Version Front and Rear Views
Table 1: WP-301xl Wall Plate US Version Front and Rear Features
# Feature Function
1 ON LED Lights red when receiving power (when no signal is
2 COMPUTER IN 15-pin HD Connector Connect to the computer graphics source
3 AUDIO IN 3.5mm Mini Jack Connect to the audio source
4 RJ-45 Connector Connect to the SV-551/SV-552 Processor/Controller
5 DC IN Power Connector Connect to the 12V power supply (supplied free)
Wiring the Twisted Pair RJ-45 Connector
The US versions of the wall plates are equipped with RJ-45 terminals. Figure 2 defines the
STP pinout using a straight pin to pin cable with RJ-45 connectors. For STP cable, cable
shielding must be connected/soldered to the connector shield.
detected); lights green when receiving a signal
EIA /TI A 568B
PIN Wire Color
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
Pair 1 4 and 5
Pair 2 1 and 2
Pair 3 3 and 6
Pair 4 7 and 8
Figure 2: RJ-45 Pinout (U.S.)
WP-301xl Wall Plate EU/UK Versions
Figure 3 and Table 2 define the EU/UK version of the WP-301xl Wall Plate.
Destination Belgium and
Germany
Figure 3: WP-301xl Wall Plate EU/UK Front and Rear Views
Table 2: WP-301xl Wall Plate EU/UK Front and Rear Features
# Feature Function
1 ON LED Lights red when receiving power (when no signal is
2 COMPUTER IN 15-pin HD Connector Connect to the computer graphics source
3 AUDIO IN 3.5mm Mini Connector Connect to the audio source
4 Terminal Block Connect to SV-551/SV-552 Processor/Controller (see
5 +12V GND 2-pin Power Terminal Block Connect to the 12V power supply (included)
6 GROUND Connection Ring tongue terminal and grounding screw
rest of Europe (excluding
detected); lights green when receiving a signal
Figure 4)
Rear panel view
Wiring the U.K. and European TP Terminal Blocks
PN:
2900-000771
Rev:
1
The European wall plates are equipped with an easy plug-in terminal block to attach the
twisted pair cables. Follow the colors of the color-coded sticker on these terminals for
proper connection of the cable.
Figure 4 defines the pinouts for the TP terminal block.
Figure 4: WP-301xl Wall Plate EU/UK TP Terminal Block Pinouts
Notes:
WP-301xl
Wall Plate
• Use the connector clips when removing the wires, not when inserting them
• Each wire protrudes 9mm in length from the plastic insulation so that it can be easily connected. To
prevent the wires crossing, be sure that each wire is completely inserted
• The cable ground shielding must be connected / soldered to the connector shield
Installation Instructions
Grounding the Wall Plate
Use the grounding screw to earth the chassis of the unit to the ground of the building. This
prevents static electricity from interfering with the product’s performance.
Figure 5 defines the grounding screw components.
# Item
1 M3X6 screw
2 1/8" Toothed Lock Washer
3 M3 Ring Tongue Terminal
Figure 5: Grounding Screw Components
To ground the wall plate:
1. Connect the ring tongue terminal to the building grounding point wire. We recommend
using a green-yellow AWG#18 wire, crimped with a proper hand-tool.
2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the
order shown above.
3. Insert the M3x6 screw (through the two toothed lock washers and ring tongue terminal)
into the grounding screw hole and tighten the screw.
For the latest information on our products and a list of Kramer distributors,
visit our Web site at
Uhttp://www.kramerelectronics.comU
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900-000771 REV 1
Loading...