Kramer VM-2HDT Quick Start Guide

2900- 30085 9 QS

Scan for full manual

VM-2HDT, VM-3HDT Quick Start Guide

IN LED

Lights when an active input signal is detected.

LINK LEDs (1 to 3)

Lights when a link is established with the receiver (VM-2HDT: 1 to 2).

(LOOP and 1 to

VM-2HDT

INPUT HDMI Connector

Connects to the HDMI source.

LOOP OUT HDMI Connector

Connect to a local monitor or a daisy-chained distributor, for example, a VM-4HDT.

TP-580R (VM-2HDT

port of the HDbaseT receiver.

SETUP 8-way DIP-switch

Used to set the IR and RS-232 command behavior.

This guide helps you install and use your VM-2HDT, VM-3HDT for the first time.

Go to www.kramerav.com/downloads/VM-2HDT to download the latest user manual and check if firmware upgrades are available.

Step 1: Check what’s in the box

VM-2HDT or VM-3HDT HDBT DA/Extender

1 Power adapter and cord

4 Rubber feet

1 Quick start guide

1 Bracket set

Step 2: Get to know your VM-2HDT, VM-3HDT

This section defines the VM-3HDT. VM-2HDT is identical but has 2 HDBT OUT connectors (OUT 1 and OUT 2).

# Feature Function

1 PROGRAM Mini USB

Connector

2 EDID SETUP Button Press to capture one of the output EDIDs or the default EDID to the input EDID.

5 OUTPUT LEDs

6 ON LED Lights when the unit receives power.

9 HDBT OUT Connectors (1 to 3) Connect to an HDBT acceptor, for example

10 IR 3.5mm Mini Jack Connect to the remote IR sensor/emitter.

11 RS-232 3-pin Terminal Block Connect to a serial controller to control a remote device that is connected to the RS-232

13 SETUP 4-way DIP-switch For future use.

14 5V DC Connector Connects to the 5V DC power supply.

Use to send RS-232 commands. Connect to a PC to perform firmware upgrades (via K-Upload) and work with the EDID

Designer. K-Upload and EDID Designer can be downloaded from our Web site at:

www.kramerav.com/support

Lights when an active output acceptor (sink) is detected on the LOOP or HDBaseT receiver that is connected to the output (

: LOOP and 1 to 2).

: 1 to 2).

-2HDT, VM-3HDT Quick Start (P/N: 2900-300859QS REV 1)

P/N:

Rev:

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

OUT 2

DIP 2 – OFF (up)

DIP 6 – OFF (up)

Step 3: Install VM-2HDT, VM-3HDT

Install VM-2HDT, VM-3HDT using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

• Fasten a bracket (included) on each side of the unit and attach it to a flat surface.

For more information go to www.kramerav.com/downloads/VM-2HDT, VM-3HDT

• Mount the unit in a rack using an optional RK-T2B rack adapter.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VM-2HDT, VM-3HDT. For best results, we recommend that you always use Kramer high-performance cables to connect AV equipment to VM-2HDT, VM-3HDT.

Step 5: Connect the power

Connect the 5V DC power adapter to VM-2HDT, VM-3HDT and plug it into the mains electricity. Safety Instructions

Step 6: Operate VM-2HDT, VM-3HDT

To enable/disable IR and RS-232 routing, set the DIP-switches (by default, set to OFF) as follows:

Out # IR Routing is enabled when: RS-232 Routing is enabled when:

OUT 1 DIP 1 – OFF (up) DIP 5 – OFF (up)

OUT 3 DIP 3 – OFF (up) DIP 7 – OFF (up)

+ 2 hidden pages