Page 1
TP-600TR Quick Start
P/N:
2900- 301502QS
Rev:
1
Scan for full manual
TP-600TR Quick Start Guide
This guide helps you install and use your TP-600TR for the first time.
Go to www.kramerav.com/downloads/TP-600TR to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
TP-600TR 4K60 HDMI/USB Extender
1 Bracket set
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your TP-600TR
The extender device functions as a transmitter or a receiver side per DIP-switch setting (see Step 4:Connect inputs and
outputs).
#
Feature
Function
1
HOST USB B 2.0 Connector
Connect to the USB host (for example, a laptop) to communicate with the USB
peripheral devices (for example, a smart board) connected to USB device ports on
either the transmitter or the receiver sides of the extender (see Step 4:Connect
inputs and outputs).
2
ACTIVE HOST LED
Lights orange when the USB host side is active
3
ACTIVE Rx LED
Lights green when the extender receiver function is active
4
IN LED
Lights blue when an active HDMI input signal is detected on HDMI IN.
5
OUT LED
Lights blue when an output acceptor device is connected.
6
TX LOOP
Transmitter mode
Lights blue an active signal is transmitted on the Tx LOOP port.
Receiver mode
N/A
7
LINK LED
Lights green when the HDBT active link connection is established.
8
ON LED
Lights green when the device receives power.
9
HDBT RJ-45 Connector
Connect to the HDBT RJ-45 connector on a paired receiver/transmitter device (for
example, a second TP-600TR device).
10
HDMI TX IN Connector
Transmitter mode
Connect to an HDMI source.
Receiver Mode
N/A
11
HDMI Rx OUT/Tx LOOP Connector
Transmitter mode
Connect to a local acceptor.
Receiver mode
Connect to an HDMI acceptor.
12
USB A 2.0 Fast-Charging Connectors
(3)
Connect to the USB local peripheral devices (for example, a USB camera, a
soundbar, microphone and so on).
13
IR 3.5mm Mini Jack Connector
Connect to an external IR emitter to control a local IR-controlled device from the
remote extender (for example, TP-600TR).
Connect to an IR sensor to control a remote IR-controlled device connected to the
remote extender side (for example, TP-600TR).
14
RS-232 3-pin Terminal Block
Connect to a controller device (for example, SL240C) to control a remote device via
serial connection (for example, the remotely connected PTZ USB camera).
15
SETUP 4-way DIP-switch
Sets the device behavior (see Step 4:Connect inputs and outputs).
16
12V DC Power Connector
Connect to the power supply.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Page 2
Step 3: Mount TP-600TR
Install TP-600TR using one of the following methods:
• Attach the rubber feet and place the unit on a flat surface.
• Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/TP-600TR).
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/TP-600TR).
• Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your TP-600TR extender.
Wiring the RJ-45 Connectors
This section defines the HDBT pinout, using a straight pin-to-pin cable with
RJ-45 connectors.
EIA /TIA 568B
PIN
Wire Color
1
Orange / White
For HDBT cables, it is recommended that the cable ground
shielding be connected/soldered to the connector shield.
2
Orange
3
Green / White
4
Blue
To achieve specified extension distances, use the recommended
Kramer cables available at www.kramerav.com/product/TP-
600TR. Using third-party cables may cause damage!
5
Blue / White
6
Green
7
Brown / White
8
Brown
Setting the DIP Switches
• All DIP-switches are set to OFF (up) by default
• All changes in DIP-Switches apply immediately, on-the-fly (no need to power cycle the device), except for
DIP-switches 1 and 2.
#
Feature
DIP-switch Settings
1
Device Operation Mode
OFF (up) – Receiver mode is active.
ON (down) – Transmitter mode is active.
2
Active USB Host port
OFF (up) – Host is active.
ON (down) – Host is inactive (active on remote paired device).
3
Define IR Pass-through
OFF (up) – Pass-through the IR signal to or from the IR cable.
ON (down) – Add IR modulation (38kHz) to the IR output signal (applies only when the IR port is connected
to an IR emitter cable).
4
Programing RS-232
Off (up) – Normal operation mode is enabled (FW programming RS-232 is inactive).
On (down) – FW programming RS-232 is active.
Step 5: Connect power
Connect the power cord to TP-600TR and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.
Warning:
• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.
Loading...