Page 1
Kramer Electronics, Ltd.
USER MANUAL
Models:
TP-104,
XGA Line Transmitter / DA
TP-105,
CAT5 Line Driver / DA
TP-121,
XGA / Audio Line Transmitter
TP-122,
XGA / Audio Line Receiver
TP-123,
XGA / Audio / Data Line Transmitter
TP-124,
XGA / Audio / Data Line Receiver
Page 2
Contents
i
Contents
1
Introduction 1
2
Getting Started 1
3
Overview 1
4
Your TP-104 XGA Line Transmitter / DA 3
5
Your TP-105 CAT5 Line Driver / DA 4
6
Your TP-121 / TP-122 5
6.1
Your TP-121 XGA / Audio Line Transmitter 5
6.2
Your TP-122 XGA / Audio Line Receiver 6
6.2.1 Your TP-122 XGA / Audio Line Receiver (Topside) 6
6.2.2 Your TP-122 XGA / Audio Line Receiver (Underside) 7
7
Your TP-123 / TP-124 8
7.1
Your TP-123 XGA / Audio / Data Line Transmitter 8
7.2
Your TP-124 XGA / Audio / Data Line Receiver 9
8
Connecting the XGA / Audio Line Transmitter / Receiver 11
8.1
Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors 13
9
Connecting the XGA / Audio / Data Line Transmitter / Receiver 14
9.1
Controlling via RS-232 (for example, using a PC) 16
10
Configuring a 1:4 XGA to TP Transmitter / Receiver / DA 17
11
Configuring a TP-105 CAT5 Line Driver / DA 19
12
Technical Specifications 21
Figures
Figure 1: TP-104 XGA Line Transmitter / DA 3
Figure 2: TP-105 CAT5 Line Driver / DA 4
Figure 3: TP-121 XGA / Audio Line Transmitter 5
Figure 4: TP-122 XGA / Audio Line Receiver (Topside) 6
Figure 5: TP-122 XGA / Audio Line Receiver (Underside) 7
Figure 6: TP-123 XGA / Audio / Data Line Transmitter 8
Figure 7: TP-124 XGA / Audio / Data Line Receiver (Topside) 10
Figure 8: Connecting the XGA / Audio Line Transmitter / Receiver System 12
Figure 9: CAT5 PINOUT 13
Figure 10: Connecting the XGA / Audio / Data Line Transmitter / Receiver System 15
Figure 11: RS-232 PINOUT Connection 16
Figure 12: Configuring a 1:4 XGA to Twisted Pair Transmitter / Receiver / DA 18
Figure 13: Configuring a TP-105 CAT5 Line Driver / DA 20
Page 3
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Contents
ii
Tables
Table 1: TP-104 XGA Line Transmitter / DA Features 3
Table 2: TP-105 CAT5 Line Driver / DA Features 4
Table 3: TP-121 XGA / Audio Line Transmitter Features 5
Table 4: TP-122 XGA / Audio Line Receiver (Topside) Features 7
Table 5: TP-122 XGA / Audio Line Receiver (Underside) Features 7
Table 6: TP-123 XGA / Audio / Data Line Transmitter Features 9
Table 7: TP-124 XGA / Audio / Data Line Receiver (Topside) Features 10
Table 8: CAT5 PINOUT 13
Table 9: RS-232 PINOUT Connection 16
Table 10: Technical Specifications of the TP-104 (with 60m CAT5 cable) 21
Table 11: Technical Specifications of the TP-105 (with 60m CAT5 cable) 21
Table 12: Technical Specifications of the TP-121 / TP-122 / TP-123 / TP-124 22
Page 4
Introduction
1
1 Introduction
Welcome to Kramer Electronics (since 1981): a world of unique, creative and
affordable solutions to the infinite range of problems that confront the video, audio
and presentation professional on a daily basis. In recent years, we have redesigned
and upgraded most of our line, making the best even better! Our 350-plus
different models now appear in 8 Groups1, which are clearly defined by function.
Congratulations on purchasing your Kramer TOOLS: TP-104 XGA Line
Transmitter / DA, and/or TP-105, CAT5 Line Driver / DA, and/or TP-121
XGA / Audio Line Transmitter, and/or TP-122 XGA / Audio Line Receiver,
and/or TP-123, XGA / Audio / Data Line Transmitter, and/or TP-124, XGA /
Audio / Data Line Receiver, which are ideal for:
Presentation and multimedia applications
Long range graphics distribution for schools, hospitals, security, and stores
The package includes one or more of the following Kramer TOOLS:
TP-104, TP-105, TP-121, TP-122, TP-123, or TP-124
Power adapter (12V DC Input) and this user manual2
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Use Kramer high performance high resolution cables3
3 Overview
This user manual describes the following Kramer TOOLS products:
TP-104 XGA Line Transmitter / DA, which is a line transmitter / 1:4 DA
that receives an XGA signal and transmits it over 4 CAT5 cables to
appropriate receivers, see section 4
TP-105 CAT5 Line Driver / DA, which receives a CAT5 input, and
distributes it to 2 identical outputs, see section 5
1 GROUP 1: Distribution Amplifiers; GROUP 2: Video and Audio Switchers, Matrix Switchers and Controllers; GROUP 3:
Video, Audio, VGA/XGA Processors; GROUP 4: Interfaces and Sync Processors; GROUP 5: Twisted Pair Interfaces;
GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors
2 Download up-to-date Kramer user manuals from the Internet at this URL: http://www.kramerelectronics.com
3 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
Page 5
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
2
TP-121 XGA / Audio Line Transmitter and the TP-122 XGA / Audio Line
Receiver, see section 6
TP-123 XGA / Audio / Data Line Transmitter and the TP-124 XGA /
Audio / Data Line Receiver, see section 7
Achieving the best performance means:
Connecting only good quality connection cables, thus avoiding
interference, deterioration in signal quality due to poor matching, and elevated
noise levels (often associated with low quality cables)
Avoiding interference from neighboring electrical appliances
Positioning your Kramer TOOLS away from moisture, excessive sunlight
and dust
In applications with high interference, shielded twisted pair (STP) cable will
give better results.
Page 6
Your TP-104 XGA Line Transmitter / DA
3
4 Your TP-104 XGA Line Transmitter / DA
The TP-104 is a line transmitter / 1:4 DA that receives an XGA signal1 and
transmits it over 4 CAT5 cables to appropriate receivers. In particular, the
TP-104:
Has a video bandwidth of more than 150MHz, with a transmission range
of more than 300 ft. (more than 100 meters)
Can power or be powered by the receiver over the same CAT5 cable
Is 12VDC fed
Figure 1 and Table 1 define the TP-104:
Figure 1: TP-104 XGA Line Transmitter / DA
Table 1: TP-104 XGA Line Transmitter / DA Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 OUT 1 RJ-45 Connector
Connects to2 the LINE IN RJ-45 connector on the TP-122 XGA /
Audio Line Receiver or the TP-120 XGA Line Receiver
3
3 OUT 2 RJ-45 Connector
Connects to2 the LINE IN RJ-45 connector on the TP-122 XGA /
Audio Line Receiver or the TP-120 XGA Line Receiver
3
4 OUT 3 RJ-45 Connector
Connects to2 the LINE IN RJ-45 connector on the TP-122 XGA /
Audio Line Receiver or the TP-120 XGA Line Receiver
3
5 OUT 4 RJ-45 Connector
Connects to2 the LINE IN RJ-45 connector on the TP-122 XGA /
Audio Line Receiver or the TP-120 XGA Line Receiver
3
6 ON LED Illuminates when receiving power
7 XGA INPUT HD15F Connector Connect to the XGA source
1 The terminology XGA is used throughout this manual, where this implies any RGBHV signal on an HD15 connector
having a resolution from VGA up to XGA
2 Using a
UTP CAT5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
3 Refer to the separate user manual: PT-110, WP-110, TP-120, which can be downloaded from the Internet at this URL:
http://www.kramerelectronics.com. Also, see the example illustrated in Figure 12
Page 7
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your TP-105 CAT5 Line Driver / DA
4
5 Your TP-105 CAT5 Line Driver / DA
The TP-105 receives a CAT5 input, and distributes it to 2 identical outputs.
In particular, the TP-105:
Has a transmission range of more than 300 ft. (more than 100 meters)
over UTP cabling
Includes EQ. and level controls
Is 12VDC fed
Figure 2 and Table 2 define the TP-105:
Figure 2: TP-105 CAT5 Line Driver / DA
Table 2: TP-105 CAT5 Line Driver / DA Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 OUT 2 RJ-45 Connector
Connects to1 the LINE IN RJ-45 connector on the TP-120 XGA Line
Receiver
3 OUT 1 RJ-45 Connector
Connects to1 the LINE IN RJ-45 connector on the TP-120 XGA Line
Receiver
4 INPUT RJ-45 Connector
Connects to1 the LINE OUT RJ-45 connector on the PT110 XGA
Line Transmitter
5 ON LED Illuminates when receiving power
6 LEVEL Trimmer Adjusts2 the video signal level
7 EQ. Trimmer Adjusts the video EQ. (equalization) compensation
1 Using a UTP CAT5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 Insert a screwdriver into the hole and carefully rotate it, to trim the level
Page 8
Your TP-121 / TP-122
5
6 Your TP-121 / TP-122
This section defines the TP-121 XGA / Audio Line Transmitter (see section
6.1), and the TP-122 XGA / Audio Line Receiver (see section 6.2).
6.1 Your TP-121 XGA / Audio Line Transmitter
The TP-121 is an XGA / audio stereo line transmitter that receives an XGA
signal and an unbalanced stereo analog audio signal and transmits them over
CAT5 cable to a TP-122 receiver, converting the unbalanced stereo analog
audio signal to digital audio (S/PDIF) stream before transmitting, thus
preserving the quality of the audio signal. In particular, the TP-121:
Has a 350MHz video bandwidth, with a transmission range of more than
300 ft. (more than 100 meters), and a 20kHz audio bandwidth with an S/N
ratio that exceeds 80dB on the same transmission range
Can power or be powered by the receiver over the same CAT5 cable
Is 12VDC fed
Figure 3 and Table 3 define the TP-121:
Figure 3: TP-121 XGA / Audio Line Transmitter
Table 3: TP-121 XGA / Audio Line Transmitter Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 AUDIO IN 3.5mm Mini Jack Connects to the audio source
3 LINE OUT RJ-45 Connector
Connects to1 the LINE IN RJ-45 connector on the TP-122 XGA / Audio
Line Receiver
4 XGA IN HD15F Connector Connect to the XGA source
5 ON LED Illuminates when receiving power
1 Using a UTP CAT5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
Page 9
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your TP-121 / TP-122
6
6.2 Your TP-122 XGA / Audio Line Receiver
This section describes the topside (see section 6.2.1), and the underside1 (see
section 6.2.2) of the TP-122 XGA / Audio Line Receiver.
6.2.1 Your TP-122 XGA / Audio Line Receiver (Topside)
The TP-122 is an XGA / audio line receiver that receives the coded CAT5
signal transmitted by a TP-121, decodes it and converts it to XGA, stereo
analog and S/PDIF digital audio outputs. The TP-122, with a TP-121, allows
an operation range of more than 300 ft. (more than 100 meters) over standard
CAT5 cable. In addition, the TP-122:
Can power or be powered by the transmitter over the same CAT5 cable
Can change the polarity of decoding H and V Sync for video
Includes EQ. and level controls
Is 12VDC fed
Figure 4 and Table 4 define the TP-122 XGA / Audio Line Receiver topside:
Figure 4: TP-122 XGA / Audio Line Receiver (Topside)
1 The underside is identical on the TP-122 and TP-124
Page 10
Your TP-121 / TP-122
7
Table 4: TP-122 XGA / Audio Line Receiver (Topside) Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 S/PDIF RCA connector Connects to the digital audio acceptor
3
AUDIO
OUT
ANALOG 3.5mm Mini Jack Connects to the analog audio acceptor
4 LINE IN RJ-45 Connector
Connects to1 the LINE OUT RJ-45 connector on the TP-121
XGA / Audio Line Transmitter or TP-104 XGA Line Transmitter / DA
5 XGA OUT HD15F Connector Connects to the XGA acceptor
6 ON LED Illuminates when receiving power
7 EQ.2 Trimmer Adjusts3 the cable compensation equalization level
8 LEVEL Trimmer Adjusts3 the output signal level
9 LINK LED Illuminates when receiving the correct input signal
6.2.2 Your TP-122 XGA / Audio Line Receiver (Underside)
Figure 5 and Table 5 define the underside4 of the TP-122 XGA / Audio Line
Receiver:
Figure 5: TP-122 XGA / Audio Line Receiver (Underside4)
Table 5: TP-122 XGA / Audio Line Receiver (Underside) Features
# Feature Function
1 HS Switch Slide the switch up5, to set the H SYNC to positive polarity; slide the switch down, to
set the H SYNC to negative polarity
2 VS Switch Slide the switch up5, to set the V SYNC to positive polarity; slide the switch down, to
set the V SYNC to negative polarity
1 Using a UTP CAT5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
4 The underside is identical on the TP-122 and TP-124
5 By default, both switches are set down (for a negative V SYNC and H SYNC polarity)
Page 11
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your TP-123 / TP-124
8
7 Your TP-123 / TP-124
This section describes the TP-123 XGA / Audio / Data Line Transmitter (see
section 7.1), and the TP-124 XGA / Audio / Data Line Receiver (see section 7.2).
7.1 Your TP-123 XGA / Audio / Data Line Transmitter
The TP-123 is a high performance transmitter that accepts a computer
graphics input signal, an unbalanced stereo analog audio signal, unidirectional
(RxD) RS 232 control commands and 12V DC power, over CAT5 cable, and
transmits to a TP-124 receiver. The stereo analog audio signal is converted to
the digital audio (S/PDIF) stream before transmitting, thus preserving the
quality of the audio source signals.
The TP-123 / TP-124 pair has a transmission range of more than 300 ft.
(more than 100 meters) over UTP cabling. In addition, the TP-123:
Has video bandwidth that exceeds 350MHz
Can power or be powered by the TP-124 receiver over the same CAT5 cable
Is 12VDC fed
Figure 6 and Table 6 define the TP-123:
Figure 6: TP-123 XGA / Audio / Data Line Transmitter
Page 12
Your TP-123 / TP-124
9
Table 6: TP-123 XGA / Audio / Data Line Transmitter Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 AUDIO IN 3.5mm Mini Jack Connects to the audio source
3 RS-232 Terminal Block
Connector
Connects to the PC or the Remote Controller (see section 9.1)
4 LINE OUT RJ-45 Connector
Connects to1 the LINE IN RJ-45 connector on the TP-122 XGA / Audio
Line Receiver
5 XGA IN HD15F Connector Connect to the XGA source
6 ON LED Illuminates when receiving power
7.2 Your TP-124 XGA / Audio / Data Line Receiver
The TP-124 is a high performance receiver obtaining the computer graphics
signal/audio/control data from the Kramer TP-123 via UTP cabling at its
CAT5 Line input. The TP-124 outputs a computer graphics signal, an
unbalanced stereo analog audio signal, a converted digital audio (S/PDIF)
signal and RS-232 control commands. The unidirectional (TxD) RS-232
interface makes it possible to control virtually any devices over a
transmission range of more than 300 ft. (more than 100 meters) over UTP
cabling. The TP-124 can power or be powered by the TP-123 transmitter
over the same CAT5 cable.
In addition, the TP-124 features:
Level and EQ. control for the XGA signals
The capability to change the polarity of decoding H and V Sync
24 bit 48kHz S/PDIF digital audio that supplies the highest quality audio
Is 12VDC fed
This section describes the topside of the TP-124 XGA / Audio / Data Line
Receiver. The underside
2
of the TP-124 is described in section 6.2.2.
1 Using a UTP CAT5 cable with RJ-45 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 The underside is identical on the TP-124 and TP-122
Page 13
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your TP-123 / TP-124
10
Figure 7 and Table 7 define the topside of the TP-124 XGA / Audio / Data
Line Receiver:
Figure 7: TP-124 XGA / Audio / Data Line Receiver (Topside)
Table 7: TP-124 XGA / Audio / Data Line Receiver (Topside) Features
# Feature Function
1 12V DC +12V DC connector for powering the unit
2 S/PDIF RCA connector Connects to the digital audio acceptor
3
AUDIO
OUT
ANALOG 3.5mm Mini Jack Connects to the analog audio acceptor
4 RS-232 Terminal Block Connector Connects to the controlled unit
5 LINE IN RJ-45 Connector
Connects to1 the LINE OUT RJ-45 connector on the TP-121
XGA / Audio Line Transmitter or TP-104 XGA Line Transmitter / DA
6 XGA OUT HD15F Connector Connect to the XGA acceptor
7 ON LED Illuminates when receiving power
8 EQ.2 Trimmer Adjusts3 the cable compensation equalization level
9 LEVEL Trimmer Adjusts3 the output signal level
10 LINK LED Illuminates when receiving the correct input signal
1 Using a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
Page 14
Connecting the XGA / Audio Line Transmitter / Receiver
11
8 Connecting the XGA / Audio Line Transmitter / Receiver
You can use the TP-121 and TP-122 to configure an XGA/Audio Line-to-Twisted
Pair Transmitter and Receiver system.
To connect the TP-121 XGA / Audio Line Transmitter with the TP-122 XGA /
Audio Line Receiver, as the example in Figure 8 illustrates, do the following:
1. On the TP-121, connect the XGA source (for example, a laptop’s graphics
card) to the XGA INPUT HD15F connector and an audio source to the
AUDIO IN 3.5mm mini jack, for example, using a Kramer C-GMA/GMA
cable (VGA HD15M +Audio jack to VGA HD15M +Audio jack)1.
Alternatively, you can connect an XGA source to the XGA INPUT
HD15F connector, and a separate audio source to the AUDIO IN 3.5mm
mini jack.
2. On the TP-122, connect the XGA OUT HD15F connector to the XGA
acceptor (for example, a display), and connect the AUDIO OUT S/PDIF
RCA connector to the digital audio acceptor (for example, an AV
Receiver), and the ANALOG 3.5mm mini jack to the analog audio
acceptor (for example, a stereo audio recorder).
3. Connect the LINE OUTPUT RJ-45 connector on the TP-121 to the LINE
IN RJ-45 connector on the TP-122, via UTP cabling (with a range of
more than 300ft (>100m)), see section 8.1.
4. Connect the 12V DC power adapter to the power socket and connect the
adapter to the mains electricity on both2 the TP-121 and the TP-122.
The signal from the XGA source is transmitted via CAT5 cable, decoded
and converted at the XGA OUT HD15F connector to the XGA acceptor.
5. On the TP-122:
Adjust3 the video output signal level and/or cable compensation
equalization level, if required
If necessary, set the H SYNC and V SYNC switches4, on the underside
1 Not supplied. The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
2 If you cannot connect the power to both the TP-121 and TP-122, you can just connect the power to the TP-122
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
4 By default, both switches are set down (for negative V SYNC and H SYNC polarity)
Page 15
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Connecting the XGA / Audio Line Transmitter / Receiver
12
Figure 8: Connecting the XGA / Audio Line Transmitter / Receiver System
Page 16
Connecting the XGA / Audio Line Transmitter / Receiver
13
8.1 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors
Table 8 and Figure 9 define the UTP CAT5 PINOUT, using a straight pin to
pin cable with RJ-45 connectors:
Table 8: CAT5 PINOUT
EIA /TIA 568A EIA /TIA 568B
PIN Wire Color PIN Wire Color
1 Green / White 1 Orange / White
2 Green 2 Orange
3 Orange / White 3 Green / White
4 Blue 4 Blue
5 Blue / White 5 Blue / White
6 Orange 6 Green
7 Brown / White 7 Brown / White
8 Brown 8 Brown
Pair 1 4 and 5 Pair 1 4 and 5
Pair 2 3 and 6 Pair 2 1 and 2
Pair 3 1 and 2 Pair 3 3 and 6
Pair 4 7 and 8
Pair 4 7 and 8
Figure 9: CAT5 PINOUT
Page 17
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Connecting the XGA / Audio / Data Line Transmitter / Receiver
14
9 Connecting the XGA / Audio / Data Line Transmitter / Receiver
You can use the TP-123 XGA / Audio / Data Line Transmitter and the TP-124
XGA / Audio / Data Line Receiver to configure a twisted pair transmitter and
receiver system, to transmit the video, audio and RS-232 control signals via
CAT5 UTP cable.
To connect the TP-123 and the TP-124 to configure a twisted pair transmitter
and receiver system, as the example in Figure 10 illustrates, do the following:
1. On the TP-123, connect:
An XGA source (for example, a laptop’s graphics card) to the XGA IN
HD15F connector and an audio source to the Audio IN 3.5mm mini jack, for
example, using a Kramer C-GMA/GMA cable (VGA HD15M +Audio jack to
VGA HD15M +Audio jack)1
An RS-232 cable with a DB9 connector at one end to the laptop, and a 2
PIN terminal block connector at the other end to the TP-123 RS-232 port2
2. On the TP-124, connect:
The XGA OUT HD15F connector to a Display
The S/PDIF Audio OUT RCA connector to a digital AV Receiver (leave
the ANALOG Audio OUT 3.5mm mini jack unconnected)
An RS-232 cable with a 2 PIN terminal block connector at one end to the
TP-124 RS-232 port2, and a DB9 connector at the other end to the RS-232
port on an RS-232 controllable device (for example, a switcher)
3. Connect the Line OUT RJ-45 connector on the TP-123 to the LINE IN
RJ-45 connector on the TP-124, via UTP cabling3 (with a range of more
than 300ft (>100m)).
4. Connect the 12V DC power adapter to the power socket and connect the
adapter to the mains electricity on both4 the TP-123 and the TP-124.
5. On the TP-124:
Adjust5 the video output signal level and/or cable compensation
equalization level, if required
If necessary, set the H SYNC and V SYNC switches6, on the underside
1 Not supplied. The full list of Kramer cables is on our Web site at http://www.kramerelectronics.com. Alternatively, you can
connect an XGA source to the XGA IN HD15F connector, and a separate audio source to the AUDIO IN 3.5mm mini jack
2 As defined in Figure 11 and Table 9 (see section 8.1)
3 For details of how to wire a CAT5 LINE IN / LINE OUT RJ-45 connector, see section 8.1
4 If you cannot connect the power to both the TP-123 and TP-124, you can just connect the power to any one unit
5 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
6 By default, both switches are set down (for negative V SYNC and H SYNC polarity)
Page 18
Connecting the XGA / Audio / Data Line Transmitter / Receiver
15
Figure 10: Connecting the XGA / Audio / Data Line Transmitter / Receiver System
Page 19
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Connecting the XGA / Audio / Data Line Transmitter / Receiver
16
9.1 Controlling via RS-232 (for example, using a PC)
Prepare an RS-232 cable with a DB9 connector at one end, and a 2 PIN
terminal block connector at the other end, as defined in Figure 11 and Table 9:
Figure 11: RS-232 PINOUT Connection
Table 9: RS-232 PINOUT Connection
Connect this PIN on the
Terminal Block Connector:
To this PIN on the
DB9 Connector
TxD PIN 2
RxD PIN 3
GND PIN 5
Page 20
Configuring a 1:4 XGA to TP Transmitter / Receiver / DA
17
10 Configuring a 1:4 XGA to TP Transmitter / Receiver / DA
You can use the TP-104 XGA Line Transmitter / DA with the TP-120 XGA
Line Receiver1 to configure a 1:4 XGA-to-Twisted Pair DA system.
To connect the TP-104 to four TP-120 units, as the example in Figure 12
illustrates, do the following:
1. On the TP-104, connect the XGA source (for example, a computer graphics
source) to the XGA INPUT HD15F connector, and connect the line output
RJ-45 connector2:
OUT 1 to the LINE IN RJ-45 connector on the TP-120 Unit I
OUT 2 to the LINE IN RJ-45 connector on the TP-120 Unit II
OUT 3 to the LINE IN RJ-45 connector on the TP-120 Unit III
OUT 4 to the LINE IN RJ-45 connector on the TP-120 Unit IV
2. On the four TP-120 units, connect the:
XGA OUT HD15F connector of Unit I to the XGA acceptor (for
example, Display 1)
XGA OUT HD15F connector of Unit II to the XGA acceptor (for
example, Display 2)
XGA OUT HD15F connector of Unit III to the XGA acceptor (for
example, Display 3)
XGA OUT HD15F connector of Unit IV to the XGA acceptor (for
example, Display 4)
3. On each of the five Kramer TOOLS, connect the 12V DC power adapter
to the power socket and connect the adapter to the mains electricity.
The signal from the XGA source is transmitted via the four CAT5 cables,
decoded and converted at the each of the XGA OUT HD15F connectors
to the XGA acceptors.
4. On each of the five Kramer TOOLS:
Adjust3 the video output signal level and/or cable compensation
equalization level, if required
If necessary, on the TP-120 units, set the H SYNC and V SYNC
switches4, on the underside
1 Refer to the separate user manual: PT-110, WP-110, TP-120, which can be downloaded from the Internet at this URL:
http://www.kramerelectronics.com
2 Via UTP cabling (with a range of more than 300ft (>100m)). For details of how to wire a CAT5 LINE IN / LINE OUT
RJ-45 connector, see section 8.1
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
4 By default, both switches are set down (for negative V SYNC and H SYNC polarity)
Page 21
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Configuring a 1:4 XGA to TP Transmitter / Receiver / DA
18
Figure 12: Configuring a 1:4 XGA to Twisted Pair Transmitter / Receiver / DA
Page 22
Configuring a TP-105 CAT5 Line Driver / DA
19
11 Configuring a TP-105 CAT5 Line Driver / DA
You can connect the TP-105 CAT5 Line Driver / DA—using a PT110 XGA
Line Transmitter and two TP-120 XGA Line Receiver1 units—to transmit a
computer graphics signal to two displays via long line CAT5 UTP cabling.
To connect the TP-105, as the example in Figure 12 illustrates, do the
following:
1. On the PT110, connect the:
Computer graphics source to the XGA INPUT HD15F connector
LINE OUTPUT RJ-45 connector2 to the INPUT RJ-45 connector on the
TP-105
2. On the TP-105, connect the:
OUT 1 RJ-45 connector to the LINE IN RJ-45 on the first TP-120
OUT 2 RJ-45 connector to the LINE IN RJ-45 on the second TP-120
3. On the two TP-120 units, connect the:
XGA OUT HD15F connector on the first TP-120 unit to the XGA
acceptor (for example, Display 1)
XGA OUT HD15F connector on the second TP-120 unit to the XGA
acceptor (for example, Display 2)
4. On each of the four Kramer units, connect the 12V DC power adapter to
the power socket and connect the adapter to the mains electricity.
The signal from the XGA source is transmitted via the two CAT5 cables,
decoded and converted at the each of the XGA OUT HD15F connectors
to the XGA acceptors.
5. If necessary:
Adjust3 the video output signal level and/or cable compensation
equalization level on the TP-105 and on both the TP-120 units
Set the H SYNC and V SYNC switches4 on the underside of the TP-120
units
1 Refer to the separate user manual: PT-110, WP-110, TP-120, which can be downloaded from the Internet at this URL:
http://www.kramerelectronics.com
2 Via UTP cabling (with a range of more than 300ft (>100m)). For details of how to wire a CAT5 LINE IN / LINE OUT
RJ-45 connector, see section 8.1
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
4 By default, both switches are set down (for negative V SYNC and H SYNC polarity)
Page 23
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Configuring a TP-105 CAT5 Line Driver / DA
20
Figure 13: Configuring a TP-105 CAT5 Line Driver / DA
Page 24
Technical Specifications
21
12 Technical Specifications1
Table 10 includes the technical specifications of the TP-104, Table 11
includes the technical specifications of the TP-105, and Table 12 includes the
technical specifications of the TP-121, TP-122, TP-123, and TP-124:
Table 10: Technical Specifications of the TP-104 (with 60m CAT5 cable)
TP-104
INPUTS: 1 VGA / UXGA on an HD15 connector
OUTPUTS: 4 RJ-45 OUT connectors
MAX. OUTPUT LEVEL: 1.4Vpp
BANDWIDTH (-3dB)2: >150MHz
DIFF. GAIN2: 3.2%
DIFF. PHASE2: 0.5 Deg
K-FACTOR2: <0.05%
S/N RATIO2: 80dB
CONTROLS2: EQ.: 0 to 33dB;
LEVEL: –7.5dB to 4.4dB
COUPLING2: AC
POWER SOURCE: 12 VDC 180mA
DIMENSIONS: 12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98", W, D, H)
WEIGHT: 0.3 kg. (0.67 lbs.) approx.
ACCESSORIES: Power supply
Table 11: Technical Specifications of the TP-105 (with 60m CAT5 cable)
TP-105
INPUTS: 1 RJ-45 OUT connector
OUTPUTS: 2 RJ-45 OUT connectors
MAX. OUTPUT LEVEL: 1.6Vpp
BANDWIDTH (-3dB)3: Appropriate for VGA-UXGA
DIFF. GAIN3: 3.7%
DIFF. PHASE3: 0.5 Deg
K-FACTOR3: <0.05%
S/N RATIO3: 69dB
CONTROLS3: EQ.: 0 to 4.4dB @ 50MHz;
LEVEL: –5.5dB to 1.4dB
COUPLING3: AC
POWER SOURCE: 12 VDC 220mA
DIMENSIONS: 12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98", W, D, H)
WEIGHT: 0.3 kg. (0.67 lbs.) approx.
ACCESSORIES: Power supply
1 Specifications are subject to change without notice
2 For the TP-104 Transmitter/ TP-120 Receiver SETUP
3 For the PT-110 to TP-105 to TP-120 Receiver SETUP
Page 25
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications
22
Table 12: Technical Specifications of the TP-121 / TP-122 / TP-123 / TP-124
TP-121 TP-122 TP-123 TP-124
INPUTS: VIDEO: 1 VGA /
UXGA on an
HD15 connector
AUDIO: 1 audio
ANALOG 3.5mm
mini jack
1 RJ-45 LINE IN
connector
VIDEO: 1 VGA /
UXGA on an HD15
connector
AUDIO: 1 audio
ANALOG 3.5mm
mini jack
1 RJ-45 LINE IN
connector
OUTPUTS: 1 RJ-45 OUT
connector
VIDEO: 1 VGA /
UXGA on an
HD15 connector
AUDIO:
1 audio S/PDIF
RCA connector
1 audio ANALOG
3.5mm mini jack
1 RJ-45 OUT
connector
VIDEO: 1 VGA /
UXGA on an HD15
connector
AUDIO:
1 audio S/PDIF RCA
connector
1 audio ANALOG
3.5mm mini jack
MAX. OUTPUT LEVEL: VIDEO: 1V
AUDIO: 2.5V
VIDEO: 1V
AUDIO: 2.5V
CONTROLS: Level: –7.5dB to
+4.4dB,
EQ.: 0dB to
+33dBm (130m)
@ 50MHz
RS-232 2 PIN
Terminal Block
RS-232 2 PIN
Terminal Block
Level: –7.5dB to
+4.4dB,
EQ.: 0dB to +33dBm
(130m) @ 50MHz
BANDWIDTH (-3dB)1: AUDIO: 20Hz – 20kHz@0.5dB
S/N RATIO: AUDIO: <–80dB
TOTAL GAIN: AUDIO:
Analog/analog: 0dB
Analog/SPDIF: –12dBFS
COUPLING: AC
TND+N: AUDIO: <0.01%
POWER SOURCE: 12 VDC 60mA
DIMENSIONS: 12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98", W, D, H)
WEIGHT: 0.3 kg. (0.67 lbs.) approx.
ACCESSORIES: Power supply
1 For the Transmitter/Receiver pair
Page 26
23
LIMITED WARRANTY
Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the
following terms.
HOW LONG IS THE WARRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
WHO IS PROTECTED?
Only the first purchase customer may enforce this warranty.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in material or workmanship in this product. The following are not covered
by the warranty:
1. Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are
uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the web site
www.kramerelectronics.com.
2. Any product, on which the serial number has been defaced, modified or removed.
3. Damage, deterioration or malfunction resulting from:
i) Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
ii) Product modification, or failure to follow instructions supplied with the product
iii) Repair or attempted repair by anyone not authorized by Kramer
iv) Any shipment of the product (claims must be presented to the carrier)
v) Removal or installation of the product
vi) Any other cause, which does not relate to a product defect
vii) Cartons, equipment enclosures, cables or accessories used in conjunction with the product
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1. Removal or installations charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the
responsibility of the Kramer dealer from whom the product was purchased.
3. Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage,
and should be included in any shipment of the product. Please also include in any mailing a contact name, company, address, and
a description of the problem(s).
3. For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WARRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to
the length of this warranty.
EXCLUSION OF DAMAGES
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer
shall not be liable for:
1. Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss
of time, commercial loss; or:
2. Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation o f incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
This equipment has been tested to determine compliance with the requirements of:
EN-50081: "Electromagnetic compatibility (EMC);
generic emission standard.
Part 1: Residential, commercial and light industry"
EN-50082: "Electromagnetic compatibility (EMC) generic immunity standard.
Part 1: Residential, commercial and light industry environment".
CFR-47: FCC Rules and Regulations:
Part 15: “Radio frequency devices
Subpart B – Unintentional radiators”
CAUTION!
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or modifications to
the unit without the expressed approval of the manufacturer will void user authority to operate the equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.
Page 27
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900-000037 REV 3
For the latest information on our products and a list of Kramer
distributors, visit our Web site: www.kramerelectronics.com,
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Caution
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
Loading...