Page 1
The Kramer T6F-23 inner frame
2 openings for 2 power sockets
2 blank inserts
1 pass-through opening
Each power socket comes with detailed assembly instructions.
Go to http://www.kramerelectronics.com/support/product_downloads.asp to
check for up-to-date user manuals and the complete list of Kramer wall plates
and module connectors.
i
i
Congratulations on purchasing your Kramer T6F-23 inner frame for the TBUS-6xl Table
Connection bus.
Mounting the Inserts
The T6F-23 inner frame includes:
Figure 1: T6F-23 inner frame (P/N: 80-004499)
Power Socket and Power Cord Options
Various power sockets and power cords are available to use with the T6F-23, as described in the
“TBUS Modular Power Socket Installation and Power Cord” Installation Instructions, supplied with
the power socket.
You can rearrange or remove any of the plates mounted on the inner frame and replace them
with Kramer passive wall plates or connector modules for interfacing A/V type signals.
To mount a Kramer insert or connector module:
1. Unscrew the two screws that fasten the blank plate to the inner frame and remove the
blank plate.
2. Place the required Kramer insert over the opening, insert the two screws to fix the Kramer
insert in place, and tighten them.
Installing the Assembled Inner Frame
To install the T6F-23 inner frame:
1. Place the assembled inner frame inside the TBUS-6xl enclosure.
2. Set the required height using your fingers to bring the inner frame to the desired position,
screw and tighten it in place using the height adjustment screws supplied with the inner
frame.
Connecting the Cables
When replacing blank inserts with connector inserts (for example, VGA, audio, HDMI and so on):
1. Insert the cables to their appropriate connectors from underneath.
2. Secure the cables to the tie holes on the TBUS-6xl.
Do not secure the cables too tightly or too loosely. Leave a small amount of slack.
The T-2INSERT Kit Option (80-00006699)
You can install the T-2INSERT kit (which includes 1 pass-through insert and a blank insert)
instead of a power socket.
After the TBUS-6xl is connected to mains power and the proper cables, it is ready for use.
Page 2
Inserting Pass-through Cables
KR AM E R EL EC TR ON IC S L TD .
Installation
Instructions
MODEL:
T6F-23
inner frame
For the latest information on our products and a list of Kramer
distributors, visit our Web site where updates to these installation
instructions may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
P/N: 2900-300075 Rev 3
P/N:
2900-300075
Rev:
3
!
To insert the pass-through cables, for example, to connect a laptop, do the following
(see Figure 1):
1. Remove the two screws attaching the split pass-through bracket.
2. Remove the split grommet.
3. Insert the cable through the rectangular opening.
4. Open the split grommet slightly and insert the required cables.
5. Place the split bracket around the grommet and position this assembly over the Inner
Frame.
6. Place the two screws appropriately and tighten the split bracket together with the grommet
and inserted cables to the inner frame.
7. Insert the self-locking ties through the tie holes to secure the cables to the inside walls of
the enclosure.
Adjusting the Height of the Inner Frame
If needed, you can adjust the inner frame height to accommodate large or bulky cables. To
adjust, perform the following:
1. Remove the height adjustment screws, while supporting the frame from underneath with
your fingers.
2. Raise or lower the connecting surface to the required height, insert the screws, and tighten
them in place.
Loading...