Page 1
The Kramer T5F-13 Inner Frame
An opening for 1 power socket
1 cable pass-through insert
2 blank inserts
Each power socket comes with detailed assembly instructions.
Go to http://www.kramerelectronics.com/support/product_downloads.asp to
check for up-to-date user manuals and the complete list of Kramer wall
plates and module connectors.
i
i
Congratulations on purchasing your Kramer T5F-13 inner frame for the TBUS-5xl Table
Connection bus.
Mounting the Inserts
The T5F-13 inner frame includes:
Figure 1: T5F-13 Inner Frame (P/N: 80-004099)
Power Socket and Power Cord Options
Various power sockets and power cords are available to use with the T5F-13, as described in
the “TBUS Modular Power Socket Installation and Power Cord” Installation Instructions,
supplied with the power socket.
The T-2INSERT Kit Option (80-00006699)
You can install the T-2INSERT kit (which includes 1 pass-through insert and a blank insert)
instead of a power socket.
You can rearrange or remove any of the plates mounted on the inner frame and replace them
with Kramer passive wall plates or connector modules for interfacing A/V type signals.
To mount a Kramer insert or connector module:
1. Unscrew the two screws that fasten the blank plate to the inner frame and remove the
blank plate.
2. Place the required Kramer insert over the opening, insert the two screws to fix the
Kramer insert in place, and tighten them.
Installing the Assembled Inner Frame
To install the T5F-13 inner frame:
1. Place the assembled inner frame inside the TBUS-5xl enclosure.
2. Set the required height using your fingers to bring the inner frame to the desired
position, screw and tighten it in place using the height adjustment screws supplied with
the inner frame.
Connecting the Cables
When replacing blank inserts with connector inserts (for example, VGA, audio, HDMI and so
on):
1. Insert the cables to their appropriate connectors from underneath.
2. Secure the cables to the tie holes on the TBUS-5xl.
Do not secure the cables too tightly or too loosely. Leave a small amount of slack.
After the TBUS-5xl is connected to mains power and the proper cables, it is ready for use.
Page 2
Inserting Pass-through Cables
KR AM E R EL EC TR ON IC S L TD .
Installation
Instructions
MODEL:
T5F-13
Inner Frame
For the latest information on our products and a list of Kramer
distributors, visit our Web site where updates to these installation
instructions may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
P/N: 2900- 300072 Rev 3
P/N:
2900-300072
Rev:
3
!
To insert the pass-through cables (for example, to connect a laptop) do the following:
1. Remove the two screws attaching the split pass-through bracket.
2. Remove the split grommet(s).
3. Insert the cable(s) through the rectangular opening.
4. Open the split grommet slightly and insert the required cables.
5. Place the split bracket around the grommet and position this assembly over the inner
frame.
6. Place the two screws appropriately and tighten the split bracket together with the
grommet and inserted cables to the inner frame.
7. Insert the self-locking ties through the tie holes to secure the cables to the inside walls
of the enclosure.
Adjusting the Height of the Inner Frame
If needed, you can adjust the inner frame height to accommodate large or bulky cables. To
adjust, perform the following:
1. Remove the height adjustment screws, while supporting the frame from underneath with
your fingers.
2. Raise or lower the connecting surface to the required height, insert the screws, and
tighten them in place.
Loading...