Kramer PT-872XR Quick Start Guide

PT-872xr Quick Start

P/N:

2900- 301005QS

Rev:

Scan for full manual

PT-872xr Quick Start Guide

This guide helps you install and use your PT-872xr for the first time. Go to www.kramerav.com/downloads/PT-872xr to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

PT-872xr HDMI 4K Line Receiver

4 Rubber feet

1 Quick start guide

1 Power adapter and cord

1 Bracket set

IMPORTANT NOTICE!

We highly recommend using only Kramer UNIKAT cables with these products. If using 3rd party shielded CAT-6A cables, both ends of the shield must be soldered to the connectors for the products to function properly. Do not use any jumpers, unshielded wall plates or midspan cable connections. These extenders are not compatible with HDBaseT technologies. Prior to signal extension, ensure that the extension line cable is lying straight and not coiled.

Step 2: Get to know your PT-872xr

Feature

Function

LED Indicators IN

Lights when an active source is connected to HDMI IN on the PT-872xr.

OUT

Lights when an active acceptor is connected to HDMI OUT on the .

Lights when power is connected to the device.

HDMI OUT Connector

Connect to an HDMI acceptor.

SETUP DIP-switches

Set the operation DIP-switches. Both DIP-switches are set to OFF (up) by default.

Always set the DIP-switches identically on transmitter and receiver devices.

DIP-switch 1: Compression Options

OFF (up) – Standard compression level. ON (down) – High compression level for additional range extension.

DIP-switch 2:

Compression Setup

OFF (up) – Enable compression (mandatory). ON (down) – For future use.

DGKAT2 IN RJ-45 Connector

Connect to the DGKat-2.0 OUT connector on the WP-871xr using twisted pair cable.

12V DC Connector

Connect the power adapter to the device.

Step 3: Install the

Install PT-872xr using one of the following methods:

• Attach the rubber feet and place the unit on a flat surface.

• Fasten a bracket (included) on each side of the unit and attach it to a flat surface

(see www.kramerav.com/downloads/PT-872xr).

• Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/PT-872xr).

• Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.

• Avoid uneven mechanical loading.

• Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

• Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your PT-872xr.

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/PT-872xr. Using third-party cables may cause damage!

Step 5: Connect the power

Connect the 12V power adapter to the and plug it into the mains electricity. This device provides power to its counterpart via DGKat 2.0. Each device can provide or accept power over cable (PoC) via DGKat 2.0.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.

• Disconnect the power and unplug the unit from the wall before installing.

Technical Specifications

Inputs

1 DGKAT 2.0

On a female RJ-45 connector

Outputs

1 HDMI

On a female HDMI connector

Video

Transmitted Data Bandwidth

Up to 18Gbps (6Gbps per graphic channel)

Max Resolution

3840x2160@60Hz (4:4:4) 24bpp at high compression level 4096x2160@60Hz (4:4:4) 24bpp at standard compression level

Compliance

HDMI 2.0, HDCP 2.2, HDR 10

Reach Extension

We recommend that you use Kramer shielded cables to achieve optimum extension ranges.

Standard Compression Level

Up to 40m (130ft) at 4K@60Hz (4:4:4) Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp)

High Compression Level

Up to 60m (200ft) at 4K@60Hz (4:4:4) Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp)

Controls

Front Panel

IN, OUT and ON LEDs

Rear Panel

DIP-switches

Power Consumption

12V DC, 600mA when coupled with a compatible transmitter

Source

12V DC, 2A

Environmental Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory Compliance

Safety

CE, UL

Environmental

RoHs, WEEE

Enclosure

Size

Pico Tool

Net Dimensions (W, D, H)

6.2cm x 5.2cm x 2.5cm (2.4" x 2.05" x 1")

Shipping Dimensions (W, D, H)

15.7cm x 12cm x 8.7cm (6.2" x 4.7" x 3.4")

Net Weight

0.1kg (0.2lbs)

Shipping Weight

0.52kg (1.2lbs) approx.

Type

Aluminum

Cooling

Convection ventilation

Accessories

Included

1 Power adapter, 1 power cord

Specifications are subject to change without notice at www.kramerav.com