Page 1
KRAMER ELECTRONIC S L T D .
HDBT Installation
Guide
MODELS:
Kr am er H DB T
Cable Recommendations for
Usage and Termination Guidelines
For the latest information on our products and a list of Kramer distributors, visit our Web
site where updates to these cable installation instructions may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N : 2 900-300462 Rev 1
Contents
1 Introduction 1
2 General Guidelines and Recommendations 2
2.1 General Rules 2
2.2 Patch Cables and Connectors 2
3 HDBaseT Twisted Pair Cable Termination 3
Page 2
HDBT – Introduction
1
1 Introduction
This document contains successful cable installation guidelines and is intended for Kramer technical personnel or
external system integrators.
To check that you have the latest version, go to the DOWNLOADS section of our Web site at:
http://www.kramerelectronics.com/support/product_downloads.asp
To check our suggested cables listing, per product, go to http://www.kramerelectronics.com
Kramer's BC-HDKat6a is an HDBaseT certified 4-pair U/FTP (unshielded around foiled twisted pair) cable designed as
the ideal companion to Kramer's HDBaseT transmitter-receiver sets to provide optimum range and performance. It is
constructed of 4 shielded twisted pairs (U/FTP) of 23AWG solid copper conductors that are cabled together in an
unshielded outer jacket, and is optimized for installations of HDBaseT twisted pair digital transmitter−receiver sets.
Although shielding is not necessary for signals using Kramer’s HDBaseT cable, it is, nonetheless highly recommended
in order to overcome electromagnetic interference to keep the quality of the signal high all along the cable run.
The Kramer high quality BC-HDKat6a HDBaseT cable (CAT 6a) passes uncompressed full HD digital video, audio,
100BaseT Ethernet, Power over Ethernet and various control signals through a single 330ft (100m) twisted pair
category cable. This cable is available in pull boxes of 305m (1000ft).
This cable was tested and accredited in an Alliance Recognized Testing facility, met the requirements set by
HDBaseT Alliance and therefore works perfectly with HDBaseT devices.
Before installing a particular cable, be sure to check that you are using the appropriate cable best suited to your
installation. Take into account the distances involved, as well as the expected performance of the connected devices
(for example, consider the expected resolutions of display devices).
Page 3
2
HDBT - General Guidelines and Recommendations
2 General Guidelines and Recommendations
It is essential that you keep away as far as possible from EMI (Electro-Magnetic Interference) environments,
and in particular:
EMI sources: Keep the cable away from electromagnetic interference environments such as high-voltage
electrical cables, electric motors (such as elevators or refrigerators), fluorescent, light-fixtures and so on
AC power cables: Keep the cable at a distance of at least 12” from AC power cables
AC power canals: Do not use electrical conduits to deploy the cable
Patch cords: For better results do not use patch cords
Proper cable termination is crucial; otherwise installation failure may occur (see Section 3):
Make sure that the drain wire is well soldered to the metal casing of the RJ-45 connectors on both cable ends
Always use the recommended Kramer RJ-45 connector (CCR-RJ45-TP6)
Keep the pairs twisted as close to the termination point as possible and make sure that the strain relief is pulled
over the purple jacket of the cable
2.1 General Rules
The following are general rules to follow during the installation.
We recommend that you:
Make only gradual bends in the cable when necessary to maintain the minimum bend radius of 4 times the cable
diameter or approximately 3cm radius
Use low-to-moderate force when pulling cable. The standard calls for a maximum of 25 lbf (pounds of force)
Never:
Bend, twist, or kink the cable at any time. Doing so may result in permanent damage to the geometry of the cable
and cause transmission failures
Over-tighten cable ties or use plastic ties
Splice or bridge Category cable at any point
Use excessive force when pulling the cable
Tie cables to electrical conduits, or lay cables on electrical fixtures
Install taut cables (cables should be loose, but not sagging)
Use staples on CAT cable that crimp the cable tightly
2.2 Patch Cables and Connectors
Ideally, the signal from the transmitter to the receiver should be transmitted using a single cable; however, often patch
cables are used to connect the device to the deployed cable. Considering that patch cables tend to be the weakest link
in the installation, they should only be used if absolutely necessary (at the transmitter or receiver), and these cables
should be kept as short as possible.
Be sure to verify that the patch cord connector is terminated using the same wiring scheme as the category cable.
Page 4
HDBT – HDBaseT Twisted Pair Cable Termination
3
3 HDBaseT Twisted Pair Cable Termination
This procedure describes how to terminate HDBT Twisted Pair cable.
Tools
You will need these tools at hand: a razor knife, wire cutters, a pair of pliers and a standard RJ-45 Crimp Tool.
Step 1: Remove part of the purple jacket
Remove approximately 2.5” of
the purple jacket using the razor
knife exposing the 4 shielded
pairs and drain wire. Fold the
drain wire over onto the cable for
future use.
Step 2: Separate the 4 pairs
Separate the 4 pairs. Use the razor
knife to carefully remove the
shielding without scoring the wires
beneath it. Repeat for all 4 pairs.
Step 3: Untwist each pair
Untwist each pair and straighten
the individual conductors. Be sure
to keep each pair together so it can
be identified.
Page 5
4
HDBT - HDBaseT Twisted Pair Cable Termination
Step 4: Insert conductors into the plastic loader
Using the standard wiring scheme shown here
(T-568B), insert the conductors into the plastic loader
piece of the R-J45 connector. The plastic loader is
necessary because the thickness of CAT 6 cable
does not allow it to sit flat in an RJ-45 connector like
in normal CAT 5. Note how the loader staggers the
cables:
Step 5: Slide the plastic loader down the cable
Slide the plastic loader down the
cable as close to the base as
possible. Keep pressure on the
top and bottom of the loader so
the cables stay in place while
sliding down.
Step 6: Cut all conductors
Using the wire cutters, cut all
conductors leaving approximately 0.5”
remaining.
Page 6
HDBT – HDBaseT Twisted Pair Cable Termination
5
Step 7: Insert the cable into the RJ-45 connector
With the orange pair on the left and the
clip of the RJ-45 connector facing
downwards, insert the cable into the
RJ-45 connector, pushing the cable all
the way in until the exposed pairs
contact the back of the connector.
Step 8: Crimp the RJ-45 connector
Using the Standard Crimp Tool, crimp
the RJ-45 connector.
Step 9: Flip the drain wire up onto the RJ-45 connector
Flip the drain wire up onto the RJ-45
connector. Clamp the strain relief
down on the purple jacket of the
BC-HDKat6a cable using the pair of
pliers.
Step 10: Solder the drain wire to the metal casing of the RJ-45 connector
Solder the drain wire to the metal
casing of the RJ-45 connector and cut
off the excess using the wire cutters.
Verify the continuity of the conductors
and the shield using a cable tester.
Loading...