Page 1
FC-404NETxl Quick Start
P/N:
2900- 301537QS
Rev:
2
Scan for full manual
FC-404NETxl Quick Start Guide
This guide helps you install and use your FC-404NETxl for the first time.
Go to www.kramerav.com/downloads/FC-404NETxl to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
FC-404NETxl 4x4 Audio and Dante Mixer
1 Power cord and adapter
1 Quick start guide
1 Bracket set
4 Rubber feet
Step 2: Get to know your FC-404NETxl
#
Feature
Function
1
OUT LEDs (1 to 4)
Lights green when a signal is present, lights red when clipping is detected.
2
IN LEDs (1 to 4)
Lights green when a signal is present, lights red when clipping is detected.
Use the embedded web pages to select line level, mic level or 48V for each input.
3
SYNC LED
Lights green when Dante network is available or red if an error occurred.
4
SYS LED
Lights green for digital audio normal operation.
Flashes green when this unit is the Master clock.
Lights red if an error has occurred.
5
Rx LED
Lights green when an RS-232 signal is received.
6
Tx LED
Lights green when an RS-232 signal is transmitted.
7
HEADPHONES 3.5mm Mini Jack
Connect to a headphone set.
8
ON LED
Lights green when the device is powered.
9
AUDIO INPUTS 3-pin Terminal
block Connectors (1 to 4)
Connect to analog balanced mono line/mic level (with selectable 48V) sources.
10
AUDIO OUTPUTS 3-pin Terminal
block Connectors (1 to 4)
Connect to analog balanced mono line level acceptors.
11
Dante RJ-45 Connector
Connect to Dante audio via the network. Provides 4 Tx channels and 4 Rx channels.
By default, DHCP is enabled.
12
RS-232 3-pin Terminal Block
Connector
Connect to a PC/serial controller.
13
ETHERNET RJ-45 Connector
Connect to a PC via a LAN.
14
RESET Recessed Button
Reset/reboot the device: press and release the button.
Reset to factory default values: press and hold the button for 30 secs.
15
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Mount FC-404NETxl
Install FC-404NETxl using one of the following methods:
• Attach the rubber feet and place the unit on a flat surface.
• Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/FC-404NETxl).
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/FC-404NETxl).
• Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.
Page 2
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your FC-404NETxl.
To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/FC-404NETxl.
Using third-party cables may cause damage!
Step 5: Connect power
If powering via PoE is not available, connect the power adapter to the FC-404NETxl and plug the power adapter into the
mains power supply.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.
Warning:
• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.
Step 6: Operate FC-404NETxl
Operate FC-404NETxl via:
• Remotely, by RS-232 serial
commands transmitted by a
touch screen system, PC, or
other serial controller
• Embedded web pages via the
Ethernet
RS-232 Control / Protocol 3000
Baud Rate:
115,200
Parity:
None
Data Bits:
8
Command Format:
ASCII
Stop Bits:
1
Example (Set Dante, channel 2 audio level input to 10): #x-aud-lvl
in.dante.1.audio.2,10
Default Ethernet Parameters (DHCP, by Default)
IP Address:
192.168.1.39
UDP Port #:
50000
Subnet mask:
255.255.255.0
TCP Port #:
5000
Gateway:
192.168.0.1
Device name:
FC-404Net-{ID} where ID = the last 4 characters of the
device’s serial number
Default Dante Parameters (Static, by Default)
Fall-back IP Address:
169.254.112.120
Subnet mask:
255.255.0.0
Gateway:
0.0.0.0
Loading...