FC
-17 Quick Start (P/N: 2900-300840QS REV 2)
P/N:
2900- 300840QS
Rev:
2
Scan for full manual
FC-17 Quick Start Guide
This guide helps you install and use your FC-17 for the first time.
Go to www.kramerav.com/downloads/FC-17 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
FC-17 4K HDMI Converter Tool
1 Power supply (5V DC)
TOOL Mounting bracket kit
4 Rubber feet
1 Quick start guide
Step 2: Get to know your FC-17
# Feature Function
1 SAMPLING INPUT LEDs Indicate the input chroma sub-sampling and color space
2
SAMPLING OUTPUT LEDs
Indicate the output chroma sub-sampling and color space
3
HDCP INPUT LEDs
Indicate the input HDCP standard
4 HDCP OUTPUT LEDs Indicate the output HDCP standard
5 ON LED Lights green when the unit is powered on; changes to red to indicate that a successful USB
LINK is established via the EDID Manager software
6
HDMI IN Connector
Connect to an HDMI source
7
HDMI OUT Connector
Connect to the HDMI acceptor
8 EDID DIP-Switches DIP 1 (INT): When ON (down), the source sees the internal default EDID
DIP 2 (EXT): When ON (down), the sour ce reads the EDID of the acceptor that is connected
to the HDMI output
DIP 3 (USER): When ON (down), the source reads a user-defined EDID
Note
: For normal operation, only one EDID DIP-switch should be set to ON (down)
9 YPbPr/420 DIP-Switch When ON:
4K50/60 YPbPr 4:4:4 signals are converted to 4:2:0
4K50/60 RGB signals are converted to YPbPr 4:2:0
Resolutions other than those above are bypas sed
10
PROG USB Port
Connect to a PC for programming use with the application software and for firmware upgrade.
11 Recessed Pushbutton Use for the upgrade process
12 5V DC +5V DC connector for powering the unit
Step 3: Install the FC-17
Install FC-17 using one of the following methods :
• Attach the rubber feet and place the unit on a flat surface.
• Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/FC-17
.
• Mount the unit in a rack using an optional RK-3T rack adapter.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your FC-17. For best results, we recommend that you always
use Kramer high-performance cables to connect AV equipment to the FC-17.
Set the DIP-switches:
DIP-Switch # Description
EDID
DIP 1 (INT)
When set to ON (down), the source sees the built-in default EDID
DIP 2 (EXT) When set to ON (down), the source sees the EDID of the sink connected to
the output
DIP 3 (USER) When set to ON (down), the source sees the EDID programmed by the user
Note
: For normal operation, set only one of the above three EDID DIP-switches to ON (down)
Sampling DIP 4
(YPbPr, 4:2:0)
When set to ON (down): 4K50/60 YPbPr 4:4:4 and 4K50/60 RGB signals
are converted to YPbPr 4:2:0; other resolutions are bypassed.
When set to OFF (up): The signal is always bypassed
Step 5: Connect the power
Connect the 5V DC power adapter to the power socket and then connect the adapter to the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Manage the EDID
The EDID is managed via the EDID DIP-switches and the EDID management software.
After downloading the EDID Manager software, connect the USB port
from the FC-17 to your PC and manage the EDID via the software:
Set the acceptor EDID as the User EDID via
the DIP-switches:
1. Disconnect the power.
2. Connect the acceptor to the FC-17’s output.
3. Set DIP 1, DIP 2 and DIP 3 to ON.
4. Connect the power.
All the LEDs flash briefly.
5. Disconnect the power, and set one of the INT,
EXT or USER DIP-switches to ON, as desired.
6. Connect the power.
Loading...