Kpnetworks ISH 1101 003 User Manual

ISH-1101-003

NZ-BOX Gateway circuit Board

Instruction Manual

Rev 1.0

2016/3/1

Kpnetworks Ltd.

- 1 - A2A-15043-00

Revision History

Description

Date

Rev 1.0

First Edition

December 15, 2015

Rev 1.1

Added Warnings.

March 1, 2016

- 2 - A2A-15043-00

Table of Contents

WARNINGS .................................................................................................................................. 4

CAUTION .................................................................................................................................... 4

KEY TO SYMBOLS ....................................................................................................................... 5

NOTE .......................................................................................................................................... 5

OVERVIEW OF THE NZ-BOX GATEWAY CIRCUIT BOARD ............................................... 7

THE FRONT BOARD .................................................................................................................... 7

THE BACK BOARD ...................................................................................................................... 8

HOW TO USE THE NZ-BOX GATEWAY CIRCUIT BOARD ............................................................... 9

INSTALLATION ............................................................................................................................ 9

POWER ON/OFF ...................................................................................................................... 10

RESET THE NZ-BOX GATEWAY CIRCUIT BOARD ....................................................................... 10

STATUS OF THE NZ-BOX GATEWAY CIRCUIT BOARD ................................................................. 11

CAUTION FOR THE OPERATION ................................................................................................. 12

REGULATORY INFORMATION TO HOST MANUFACTURER ........................................................... 13

- 3 - A2A-15043-00

Safety Warnings

Warnings

 Connect the earth wire to the outlet before turning on the power, to prevent

an electric shock. Place the power code in the outlet which is connected to

the earth wire.

 Do not use the NZ-Box Gateway circuit Board in an environment that

consists of excessive humidity or flammable gas.

 Changes or modifications not expressly approved by Kpnetworks Ltd.

responsible for compliance could void the user’s authority to operate the

equipment.

 This equipment complies with radio frequency exposure limits set forth by

the FCC and Industry Canada for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20

cm between the device and the user or bystanders. This device must not be

co-located or operating in conjunction with any other antenna or

transmitter.

 Cet équipement est conforme aux limites d'exposition aux radiofréquences

définies par la FCC et Industrie Canada pour un environnement non

contrôlé. Cet équipement doit être installé et utilisé avec un minimum de

20 cm de distance entre le dispositif et l'utilisateur ou des tiers. Ce

dispositif ne doit pas être utilisé à proximité d’une autre antenne ou d’un

autre émetteur.

Caution

 The NZ-Box Gateway circuit Board is an electrostatic sensitive device.

Pay sufficient attention to static electricity during the operation.

- 4 - A2A-15043-00

Key to Symbols

WWaarrnniinng

g

CCaauuttiioon

n

： Ensure that the operator fully understands the contents of the

statements with this sign. The warning statements indicate a

possibility of injury if operational procedures are not followed

correctly.

： Ensure that the operator fully understands the contents of the

statements with this sign. The caution statements indicate a

possibility of damage to the NZ-Box Gateway circuit Board or its

peripheral equipment if operational procedures are not followed

correctly.

Note

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

- 5 - A2A-15043-00