KP Electronic Systems ATS100 User Manual

ATS100

TM

, ATSU100

TM

Alarm Transmitter - Synthesized

The ATS100 and ATSU100 units are a new generation of advanced, high
performance, radio alarm transmitters designed to complement KP's
LARS long range radio alarm systems. Manufactured using the latest SMD
technology, the ATS units are synthesized for both VHF and UHF frequencies.

The ATS100 unit transmits periodic test signals verifying its status and alerting
the Central Monitoring Station of any service problems.
Low batteries, for example, can now be detected and replaced before
discharging, ensuring constant security monitoring and efficient maintenance.

Parallel Systems for Increased Security

Full zone and panel information can be sent via
the ATS100 by either connecting to KPs innovate
DI100 Dialer Interface or connecting directly to
a number of industry-standard alarm panels.
Messages are then sent via radio transmission
and Line Receiver ensuring complete primary/
secondary security backup.

Important Features

Synthesized VHF and UHF units

Programmable periodic test messages

Serial port for on-site parameter
programming by the FTU100
using dedicated GUP10

Interfaces with any alarm panel for transfer
of up to 256 different messages

8 dry contact inputs

Double frequencies for emergency
backup and extra protection

Compact and easy to install

TM

TM

or by PC,

utility software

Innovations For Installers:

Alarm Panel Interface

To ensure a fully redundant alarm monitoring system, KP's LARS network operates
simultaneously with phone line receivers in a primary/secondary configuration.
Alarm messages are sent using KPs innovative DI100, a dialer interface that
communicates full zone and panel information from any alarm panel via KPs radio
transmitters.
Messages are sent without interfering with phone line connections guaranteeing
radio and line receivers work independently, and that alarm and system messages
are sent at the same time.

Field Programmer Unit

Using KP's handy, pocket-sized FTU100 field programmer, parameters
within KP's radio units are viewed and changed on-site. Unit address, input
polarity and periodic test timing are quickly and effortlessly updated.

Signal Strength Monitor

The FTU101 measures and displays signal strength of KP's ATS100
transmissions to repeaters or central stations. An invaluable tool for expanding
radio networks while in the field.

PC Utility Software

The user friendly GUP5000 software for Windows enables on-site programming of
all key ATS100 parameters. The software is designed for programming frequency
and message repetitions and incorporates a user password feature ensuring authorized
access.

100mm

(4)

166mm(6.5)

32mm

(1.3)

www.kpsystems.com

Specifications

Models ATS100

General

Power Supply

Operating Temperature

Storage Temperature

RF Transmitter

Frequency

Modulation

Power Output

Frequency Stability
Spurious Emission

(below carrier)

Deviation
(factory adjusted)

Output Impedance

Digital Encoder

Encoding

Physical Dimensions

TM

DC Input 10-15 VDC, 16mA standby, 1 A max during transmission

ATS100P

-30oC to 60oC (-22oF to 140oF)

-40oC to 70oC (-40oF to 158oF)

FCC FCC

136-174

5W

-60dB

32 bit words in LARS and LARS I protocol with BCH and PARITY

136-174

5 ppm at - 30oC to 60oC (-23oF to 141oF)

+

-

-75dB

+

-

+

-

+

-

64 bit words in

LARS II protocol

TM

ATSU100

CE CE

410-504 MHz synthesized into five
sub-bands:
low 410-450 MHz [P.N ATSU100L]
edium 450-470 MHz [P.N ATSU100M]
high 470-4504Hz [P.N ATSU100H]

FM, FSK and PWM

10W

-60dB

5 KHz max

2.0 KHz for 12.5 KHz bands

3.3 KHz for 25 KHz bands

50W BNC connector

TM

2W

445-465 MHz
[P.N
ATSU100CE]

-75dB

Size 32x100x166mm (1.3x4x6.5)

Weight

0.6 kg (1.3lbs)

Head Office: P.O. Box 42, Tefen Industrial Zone, 24959, Israel. Tel: [phone], Fax: [phone], [e-mail]

US Office: 109 Tudor Drive, North Wales, PA 19454. U.S.A Tel: [phone], Fax: [phone], [e-mail]