Industrial Floor Fan
OPERATION MANUAL
Edition No : FD-001
Date of Issue : 10/2016
FD-45
2
OPERATION MANUAL
1. Front Safety Grill
2. Rear Safety Grill
3. 3 Speed Switch
4. Fan Motor (On Rear Of Fan)
5. Right Locking Tilt Nut
6. Floor Stand
7. Fan Blade
8. Le Locking Tilt Nut
1
2
3
4
7
5
6
Model FD-45
Size (mm) 450
Volt 240
Hz 50
Watt s 165
Air
Flow
130
Speed 1400
Speeds 3
SPECIFICATIONS
Voltage
Check the voltage on the specication plate is the same as
the local voltage. Do not use if they are not compatible
and contact your dealer.
e fan must be earthed to the socket.
Speed Control
e fan has a speed control, “0”is o, “3” is the fastest, “1”
is the lowest.
8
A B C D
570 240 518 560
3
OPERATION MANUAL
SAFETY INSTRUCTIONS
When using this electrical appliances, basic safety precautions should always be followed, to
reduce the risk of re, electric shock and personal injury,
• Carefully read this instruction manual before using the appliance.
• Keep young children out of reach of the appliance.
• is appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised around the appliance to ensure that they remain in a safe
environment
• Ensure that appliance does not get wet (water splashes etc.).
• Do not use appliance with wet hands.
• Always operate the appliance from a power source of the same voltage, frequency and
rating as indicated on the product identication plate.
• Position the power supply lead correctly so that it will not be walked on or pinched by
items placed on or against them.
• Use appliance only for its intended use.
• Do not use appliance if it has been dropped or any part of appliance (including cord or
plug) has been damaged. Take appliance to your nearest authorized service center or
qualied dealer for inspection or repair.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualied persons in order to avoid a hazard.
• Appliance should not be used outdoors, placed near a hot gas or electrical burner or placed
in a heated oven.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus that produce heat.
• Do not operate appliance underneath or near ammable or combustible materials (e.g.
curtains). Keep at least 300mm clearance around sides, back, front and top.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Do not block any ventilation openings.
• Turn o and unplug before cleaning or storing.
• Any type of servicing, apart from ordinary cleaning, must be carried out by an authorized
service center or qualied dealer.
• If this appliance is used by a third party, please supply the instruction manual with it.
• Do not misuse the cord. Never carry the appliance by the cord or pull to disconnect it
from the outlet. Instead, grasp the plug and pull to disconnect.
• Do not insert or allow foreign objects to enter the grille openings as this may cause
damage to the appliance and/or injury to the user.
• No liability can be accepted for any damage caused by non-compliance with these
instructions or any other improper use or mishandling of appliance.
4
OPERATION MANUAL
TILT ADJUSTMENT
To adjust and tilt the fan body; rst disconnect the fan from the power supply wall socket, then
loosen both locking tilt knobs (5 & 8) located either side of the fan by rotating anti-clockwise the
knobs
2. Tilt the fan to the desired position.
3. Re-tighten the locking tilt knobs (5 & 8) located either side of the fan.
4. Plug the fan back into the wall socket and turn ON to the desired speed using the 3 speed
switch
MAINTENANCE
When the fan is not in use, it should be cleaned and packed making sure the power lead is
protected.. It then should be stored in a dry place. Ensure that the fan is not in a place where
it could be damaged.
Loading...