Kontron KT-PCIe-DVI-HDMI-I User Manual

Page 1
KT-PCIe-DVI-HDMI-I
KT-PCIe-DVI-HDMI-I Users Guide
KTD-N0800-0
Page 2
KTD-N0800-0 Page 2
Document details
Document revision history.
Revision
0 Mar. 1st 2010 JSE/MLA Preliminary version
Date By Comment
Copyright Notice:
Copyright © 2009, KONTRON Technology A/S, ALL RIGHTS RESERVED. No part of this document may be reproduced or transmitted in any form or by any means, electronically or
mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
Trademark Acknowledgement:
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer:
KONTRON Technology A/S reserves the right to make changes, without notice, to any product, includin g circuits and/or software described or contained in this manual in order to improve design and/or performance. Specifications listed in this manual are subject to change without notice. KONTRON Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or mask work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. KONTRON Techn ology A/S makes no representation or warranty that such application will be suitable for the specified use without further testing or modification.
KT-PCIe-DVI-HDMI-I Users Guide
Page 3
KTD-N0800-0 Page 3
Document details
Life Support Policy
KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A/S.
As used herein: Life support devices or systems are devices or systems which, (a) are intended for surgical implant into body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labelling, can be reasonably expected to result in significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
KONTRON Technology Technical Support and Services
If you have questions about installing or using your KONTRON Technology Product, check this User’s Manual first – you will find answers to most questions here. To obtain support, please contact your local Distributor or Field Application Engineer (FAE).
Before Contacting Support: Please be prepared to provide as much information as possible:
CPU Board
1. Type.
2. Part Number (find PN on label)
3. Serial Number if available (find SN on label)
Configuration
1. CPU Type, Clock speed
2. DRAM Type and Size.
3. BIOS Revision (Find the Version Info in the BIOS Setup).
4. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section).
System
1. O/S Make and Version.
2. Driver Version numbers (Graphics, Network, and Audio).
3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.
Warranty
KONTRON Technology warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a similar product. Replacement Product or parts may include remanufactured or refurbished parts or components.
The warranty does not cover:
1. Damage, deterioration or malfunction resulting from: A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product. B. Repair or attempted repair by anyone not authorized by KONTRON Technology. C. Cause s external to the pro duct, such as electric power fluctuations or failure. D. Normal wear and tear. E. Any other causes which does not relate to a product defect.
2. Removal, installation, and set-up service charges.
Exclusion of damages:
KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHER WISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
KT-PCIe-DVI-HDMI-I Users Guide
Page 4
KTD-N0800-0 Page 4
» Table of Contents «
Introduction..............................................................................................5
1 Mechanical Drawings........................................................................6
2 Functional Diagram...........................................................................7
3 Jumpers............................................................................................8
4 Connectors .......................................................................................9
5 Cable Kit......................................................................................... 10
6 Installation Guide............................................................................11
7 Specifications..................................................................................12
Appendix EDID version 1.x....................................................................13
KT-PCIe-DVI-HDMI-I Users Guide
Page 5
KTD-N0800-0 Page 5
p
g
p
Introduction
Introduction
When the KT-PCIe-DVI-HDMI-I card is plugged into the PCI-Expressx16 connector then the motherboard automatically detects the card and select TMDS output. The card operates at pixel rates of up to 165MHz per link, supporting 1920x1200 panels at a 60Hz refresh rate.
Low profile DVI/HDMI module (< 35mm above MB PCB)
High-speed TMDS.
Panel resolution up to 1920x1200 or similar.
Support independent DVI and HDMI dual display.
Including Lock-Clip to fix the module to the PCIe socket.
No tools required for mounting/dismounting the module.
HDMI and DVI Interface, both manage up to 165Mpixels/s
HDMI connector mounted on the IO panel side.
DVI connector via SIL-20p and cable kit 821524.
DVI 1.0 and HDMI compliant.
Complete Windows and DOS support.
Included Low Profile Brackets for HDMI
Included Full Height ATX Bracket for HDMI, with “break-off-plate” for HDMI and for DMI.
Included Low Profile Bracket for DVI (fit the 821524 kit)
for fixin
for fixing bracket
DVI connector
821524
1
HDMI
DVI HDMI DVI + HDMI
DVI-SIL
Lock-Cli
Jum
ers
Break line
DVI
Break of module (DVI connector adapter)
Part no. 820977
PCB no. 30103350
Assem. no. 69300000
KT-PCIe-DVI-HDMI-I Users Guide
Page 6
KTD-N0800-0 Page 6
g
Mechanical Drawings
Mechanical Drawings
-1.0
0.0
(All measures in mm)
Motherboard PCB
129.4
139.5
17.0
34.6
8.0
4.4
0.0
79.2
0.0
Low Profile Brackets for HDMI
Low Profile Brackets for DVI
120.0
Full Hei
ht ATX Bracket for HDMI
KT-PCIe-DVI-HDMI-I Users Guide
Page 7
KTD-N0800-0 Page 7
r
Functional Diagram

2 Functional Diagram

820977 KT-PCIe-DVI-HDMI-I
HDMI connecto
5V Current limited supply
Level Shifter
DVI/TMDS configuration
TMDS0 TMDS1
Motherboard with multiplexed PCI-Expressx16/SDVO/TMDS connector
(Jumper settings)
PCI-Expressx16 connector
TMDS
DVI connector
Level Shifter
KT-PCIe-DVI-HDMI-I Users Guide
Page 8
KTD-N0800-0 Page 8
(

Jumpers

3 Jumpers
Jumper settings:
DVI-SIL configured for DVI
Default)
DVI-SIL configured for TMDS
How to interface EEPROM (Used to program EDID for TMDS)
Pin1
Pin 1 2 3 4 5 6 7 8 9 10 11 12
J2-3 J5-6 J7-8
Pin 1 2 3 4 5 6 7 8 9 10 11 12
J1-2 J4-5 J8-9
Pin 1 2 3 4 5 6 7 8 9 10 11 12
CLK DAT 3.3V GND (Key option)
KT-PCIe-DVI-HDMI-I Users Guide
Page 9
KTD-N0800-0 Page 9

Connectors

4 Connectors
HDMI connector
The HDMI connector is of type Samtec HDMI-19-01-S-SM or similar.
PIN Signal Type
1 TMDS Data 2+ LVDS OUT 2 GND PWR 3 TMDS Data 2- LVDS OUT 4 TMDS Data 1+ LVDS OUT 5 GND PWR 6 TMDS Data 1- LVDS OUT 7 TMDS Data 0+ LVDS OUT 8 GND PWR
9 TMDS Data 0- LVDS OUT 10 TMDS Cloc k + LVDS OUT 11 GND PWR 12 TMDS Clock- LVDS OUT 13 CEC NC 14 NC NC 15 DDC Clock IO 2K2 16 DDC Data IO 2K2 17 GND PWR 18 +5V (55mA) PWR 19 Hot Plug Detect I
20-23 GND PWR
DVI-SIL The “DVI” connector is a Hirose DF19G-20P-1H. Mating connector is Hirose DF19L-20P-1H or similar.
(In order to implement real DVI connector the cable kit 821524 must be used).
PIN Signal Type
1 GND PWR
2 GND PWR
3 +5V (55mA) PWR
4 Hot Plug Detect I
5 GND PWR
6 DDC Data IO 2K2
7 DDC Clock IO 2K2
8 GND PWR
9 TMDS Clock- LVDS OUT 10 TMDS Cloc k + LVDS OUT 11 GND PWR 12 TMDS Data 0- LVDS OUT 13 TMDS Data 0+ LVDS OUT 14 GND PWR 15 TMDS Data 1- LVDS OUT 16 TMDS Data 1+ LVDS OUT 17 GND PWR 18 TMDS Data 2- LVDS OUT 19 TMDS Data 2+ LVDS OUT 20 GND PWR
Shield GND PWR
Pull U/D
Pull U/D
KT-PCIe-DVI-HDMI-I Users Guide
Page 10
KTD-N0800-0 Page 10

Cable Kit

5 Cable Kit
DVI Converter PCB is attached as a brake off module to the KT-PCIe module. The converter contains two connectors to convert from DVI-SIL (Hirose DF19L-20P-1H) to DVI-I. The KT-PCIe-modules includes DVI cable 300mm long (PN. 821524) in order to convert the SIL-DVI
connector to a DVI-I connector.
The cable wiring is a one-to-one connection.
The DVI-I connector is a Molex 74320-1004 (or similar). Only DVI Digital output is supported. (Both DVI-I and DVI-D cables can be connected).
DVI-SIL
PIN
1 - GND 2 - GND 3 14 +5V (55mA) 4 16 Hot Plug Detect 5 15 GND 6 7 DDC Data 7 6 DDC Clock 8 - GND
9 24 TMDS Clock- 10 23 TMDS Clock+ 11 22 GND 12 17 TMDS Data 0- 13 18 TMDS Data 0+ 14 19 GND 15 9 TMDS Data 1- 16 10 TMDS Data 1+ 17 11 GND 18 1 TMDS Data 2- 19 2 TMDS Data 2+ 20 3 GND
DVI-I
PIN
1 8 9 16
17 24
Front view
Signal
C1 C2
C3 C4
C5
KT-PCIe-DVI-HDMI-I Users Guide
Page 11
KTD-N0800-0 Page 11
Installation Guide

6 Installation Guide

These KT-PCIe cards fits into a standard PCIe connector like the Molex 877159308 PCIe edge connector which has no integrated PCIe card lock.
The 820977 kit contains:
1. Cable 821524
2. Two Hex Nuts for the DVI connector to fix on a bracket
3. The 820877 module
4. Low Profile Brackets for HDMI
5. Low Profile Brackets for DVI
6. Full Height ATX Bracket for HDMI and DVI
7. Screw for fixing bracket to module
Carefully brake of the DVI Connector adapter.
The cable 821524 can be used to interface the module and the DVI Connector adapter. If DVI Bracket shall be used then fix the DVI connector to the bracket via the two Hex Nuts. If HDMI Bracket shall be used then fix HDMI Bracket to the module by screw. Insert the module to the Motherboard (KTGM45, KTQ45 or KTG41) via the PCIex16 slot nearest the CPU. No special settings required in BIOS. OS drivers include support for the module. Boot into OS and use the Intel Graphics Media Accelerator Driver to select requested display configuration.
The Lock-Clip is use to fix the module into the PCIex16 slot. In order to release the Lock-Clip press by your thumb on the top part of the Lock-clip as indicated on the picture below.
KT-PCIe-DVI-HDMI-I Users Guide
Page 12
KTD-N0800-0 Page 12
Specifications

7 Specifications

Cable length:
HDMI and DVI Cable length tested to 10 meters. Picture quality depends on display and cable, some combination might fail at high resolution (like 1600x1200) when cable length > 5 meters.
Power consumption:
The +5V available on both the HDMI and DVI can deliver minimum 0.5A even though only 55mA is required in according to DVI/HDMI standard. The +5V is protected by Resettable Fuse.
12V (via PCIe) 1.3W max. (0.55W externally and 0.75W onboard) for sourcing two times +5V/55mA.
3.3V (via PCIe) 0.4W max.
Operating temperature: 0-60ºC Maximum height above MB PCB: 34.6 mm
KT-PCIe-DVI-HDMI-I Users Guide
Page 13
KTD-N0800-0 Page 13
Appendix
Appendix EDID version 1.x.
Descriptor structure defined in the VESA EDID code loaded in EEPROM, used for support of TMDS displays. Byte Description
1. Low Byte of DClk in 10 KHz and in HEX
2. High Byte of DClk in 10 KHz and in HEX
3. Horizontal Active [pixel], LSByte
4. Hori zontal Blanking [pixel], LSByte 5-Bit 7-4: Horizontal Active [pixel], 4 MSbit (All values shall be as if 1 pixel /clock) 5-Bit 3-0: Horizontal Blanking [pixel], 4 MSBit (Blanking = Total- Active)
6. Vertical Active [lines], LSB
7. Vertical Blanking [lines], LSByte 8-Bit 7-4: Vertical Active [lines], 4 MSbit 8-Bit 3-0: Vertical Blanking [lines], 4 MSbit (Blanking = Total- Active)
9. HSync Offset (from Horizontal Blanking) [pixel], LSByte (Front Porch)
10. HSync Pulse Width [pixel], LSByte 11-Bit 7-4: VSync Offset [lines], 4 LSbit (Front Porch) 11-Bit 3-0: VSync Pulse Width [lines], 4 LSbit 12-Bit 7-6: HSync Offset (from Horizontal Blanking) [pixel], 2 MSBit (Front Porch) 12-Bit 5-4: HSync Pulse Width [pixel], 2 MSbit 12-Bit 3-2: VSync Offset [lines], 2 MSbit (Front Porch) 12-Bit 1-0: VSync Pulse Width [lines], 2 MSbit
13. Horizontal Image Size [pixel], LSByte
14. Vertical Image Size [lines], LSByte 15-Bit 7-4: Horizontal Image Size [pixel], 4MSbit 15-Bit 3-0: Vertical Image Size [lines], 4 MSbit 16: Horizontal Border [pixel] 17: Vertical Border [lines] 18-Bit 7: 0 = Non-interlaced, 1 = Interlaced 18-Bit 6-5: 00 = Reserved 18-Bit 4-3: 11 = Digital Separate 18-Bit 2: Vertical Polarity (0 = Negative, 1 = Positive) 18-Bit 1: Horizontal Polarity (0 = Negative, 1 = Positive) 18-Bit 0: 0 = Reserved
KT-PCIe-DVI-HDMI-I Users Guide
Loading...