Page 1
Page 2
Contents
Contents
Introduction..........................................................................................................3
Symbols used in this Manual.................................................................................4
Important Instructions.........................................................................................5
Note on the Warranty.............................................................................................5
Exclusion of Accident Liability Obligation...............................................................5
Liability Limitation / Exemption from the Warranty Obligation................................5
Safety Instructions ..............................................................................................6
FCC Statement......................................................................................................8
Electromagnetic Compatibility................................................................................8
Scope of Delivery.................................................................................................9
Optional Parts........................................................................................................9
Type Labels and Product Identification.................................................................. 9
Product Description ..........................................................................................10
Front Panel..........................................................................................................11
Display ............................................................................................................12
Display with Touchscreen ...............................................................................12
Controls and LED Indicator.............................................................................13
Left Side ..............................................................................................................15
Interfaces ........................................................................................................16
Power Plug......................................................................................................17
Rear Side.............................................................................................................18
Air Openings........................................................................................................19
On Screen Display (OSD)....................................................................................20
Operation of the OSD Menu............................................................................20
Power Supply ......................................................................................................21
Power Cord Connection.......................................................................................21
AC Connection................................................................................................22
DC Connection................................................................................................23
Installation Instructions....................................................................................25
Instruction for Mounting.......................................................................................25
Panelmount Version ............................................................................................26
Rackmount Version .............................................................................................26
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 1
Page 3
Contents
Monitor Connecting and Turning On ...............................................................27
Touchscreen Software Installation.......................................................................28
Selecting the Touchscreen Controller..............................................................28
Calibrating the Touchscreen............................................................................30
Maintenance and Prevention ............................................................................32
Technical Data....................................................................................................33
Mechanical Specifications....................................................................................34
Electrical Specifications .......................................................................................34
Environmental Specifications...............................................................................35
CE Directives and Standards...............................................................................36
Technical Appendix – Interfaces ......................................................................37
VGA Connector....................................................................................................37
DVI-D Connector..................................................................................................38
S-Video Connector...............................................................................................39
C-Video (Composite) Connector..........................................................................39
USB Touchscreen Connector...............................................................................39
Serial Touchscreen Connector (RS232)...............................................................40
Technical Support..............................................................................................41
Returning Defective Merchandise........................................................................ 42
2 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 4
Introduction
Introduction
Kontron Embedded Computers would like to point out that the information
contained in this manual may be subject to technical changes, particularly as a
result of continuous product upgrades.
The attached documentation does not entail any guarantee on the part of Kontron
Embedded Computers with respect to technical processes described in the
manual or any product characteristics set out in the manual. Kontron Embedded
Computers does not accept any liability for any printing errors or other
inaccuracies in the manual unless it can be proven that Kontron Embedded
Computers is aware of such errors or inaccuracies or that Kontron Embedded
Computers is unaware of these as a result of gross negligence and Kontron
Embedded Computers has failed to eliminate these errors or inaccuracies for this
reason. Kontron Embedded Computers expressly informs the user that this
manual only contains a general description of technical processes and
instructions which may not be applicable in every individual case. In cases of
doubt, please contact Kontron Embedded Computers.
This manual is protected by copyright. All rights are reserved by Kontron
Embedded Computers. Copies of all or part of this manual or translations into a
different language may only be made with the prior written consent of Kontron
Embedded Computers. Kontron Embedded Computers points out that the
information contained in this manual is continuously being updated in line with the
technical alterations and improvements made by Kontron Embedded Computers
to the products and thus this manual only reflects the technical status of the
products by Kontron Embedded Computers at the time of printing.
© 2007 by Kontron Embedded Computers
Printing and duplication, even of sections, is only permissible with the express
approval of
Kontron Embedded Computers GmbH
Oskar-von-Miller-Str. 1
85386 Eching
Germany
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 3
Page 5
Introduction
Symbols used in this Manual
Symbol Meaning
This symbol indicates the danger of injury to the user or the risk of
damage to the product if the corresponding warning notices are
not observed.
This symbol indicates that the product or parts thereof may be
damaged if the corresponding warning notices are not observed.
This symbol indicates general information about the product and
the user manual.
This symbol precedes helpful hints and tips for daily use.
4 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 6
Important Instructions
Important Instructions
This chapter contains instructions which must be observed when using your
industrial LCD monitor KFM19_e.
The manufacturer’s instructions provide useful information on your industrial LCD
monitor KFM19_e.
Note on the Warranty
Due to their limited service life, parts which, by their nature, are especially subject
to wear (wearing parts) are not included in the guarantee beyond the legal
stipulations. This applies to the display backlighting, for example.
Exclusion of Accident Liability Obligation
Kontron Embedded Computers shall be exempted from the statutory accident
liability obligation if the user fails to observe the safety instructions.
Liability Limitation / Exemption from the Warranty Obligation
In the event of damage to the device caused by failure to observe the hints in this
manual and eventually on the device (especially the safety instructions), Kontron
Embedded Computers shall not be required to honor the warranty even during the
warranty period and shall be exempted from the statutory accident liability
obligation.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 5
Page 7
Safety Instructions
Safety Instructions
Please read this section carefully and observe the instructions for your own safety
and correct use of the device.
This chapter also contains information on approval and interference suppression
of your device.
Please observe the warnings and instructions on the device and in the manual.
The industrial LCD monitor KFM19_e has been built and tested by Kontron
Embedded Computers in accordance with EN 60950/VDE 0805 and left the
company in a perfectly safe condition.
In order to maintain this condition and ensure safe operation, the user must
observe the instructions and warnings contained in this manual.
❏ The device must be used in accordance with the instructions for use.
❏ The electrical installations in the room must correspond to the requirements of
the respective regulations.
❏ Take care that there are no cables, particularly power cables, in areas where
persons can trip over them.
❏ Do not use a power cable in sockets shared by a number of other power
consumers. Do not use an extension cable.
❏ Only use the power cord supplied.
❏ The unit is only completely disconnected from the power source when the
power cord is disconnected from the power source. Therefore the power cord
and its connectors must always remain easily accessible.
❏ Do not place the device in direct sunlight, near heat sources or in a damp
place. Make sure the device has adequate ventilation.
6 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 8
Safety Instructions
❏ Only devices and components which fulfill the requirements of a SELV circuit
(Safety Extra Low Voltage) in accordance with EN 60950 may be connected
to the interfaces of the system.
❏ All plugs on the connection cables must be screwed or locked to the housing.
❏ The device is designed to be used in vertical position.
❏ Repairs may only be carried out by a person authorized by Kontron
Embedded Computers.
❏ Maintenance or repair on the open device may only be carried out by qualified
personnel authorized by Kontron Embedded Computers familiar with the
associated dangers.
❏ It is not allows to open the device.
❏ Only approved original accessories approved by Kontron Embedded
Computers may be used.
❏ It must be assumed that safe operation is no longer possible,
• if the device has visible damage or
• if the device no longer functions.
In these cases the device must be shut down and secured against
unintentional operation.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 7
Page 9
Safety Instructions
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Electromagnetic Compatibility
This product has been designed for industrial, commercial and office use,
including small business use. The most recent version of the EMC guidelines
(EMC Rules 89/336/EEC) and/or the German EMC laws apply. If the user
modifies and/or adds to the equipment (e.g. installation of add-on cards), the
prerequisites for the CE conformity declaration (safety requirements) may no
longer apply.
8 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 10
Scope of Delivery
Scope of Delivery
❏ Industrial LCD monitor KFM19_e (A or B)
❏ This user manual for the industrial LCD monitor KFM19_e
❏ KFM - OSD-Menu - Description
❏ AC power cord or DC Phoenix plug (depending on the ordered KFM19_e)
❏ VGA cable connector (2 m)
❏ 8x M4 nuts (for panelmount version only)
Optional Parts
❏ USB or serial (COM) touchscreen cable connector depending on the ordered
touchscreen terminal configuration (optional)
Available lengths for:
USB cable connector (Type A, male - Type A, male): 2m, 5m
COM (RS232) cable connector: 2 m, 5 m, 10 m
❏ VGA cable connector
Available lengths: 2 m, 5 m, 10 m
❏ DVI cable connector
Available lengths: 2 m, 5 m
❏ CD-ROM with the installation software and the driver for touchscreen (if the
KFM19_e is ordered with the optional touchscreen)
Type Labels and Product Identification
The type label of your monitor KFM19_e is attached at the back of the device.
Type label Product identification
KFM19_e - A Industrial LCD Monitor KFM19_e with AC power supply unit
KFM19_e - B Industrial LCD Monitor KFM19_e with DC power supply unit
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 9
Page 11
Product Description
Product Description
The KFM19_e is an industrial LCD monitor designed for high-performance
industrial applications. The solid type of enclosure offers to the monitor a
mechanical stability. KFM19_e is therefore proper for industrial use. Excellent
image representation, simple menu-driven handling and plug & play ability round
off the qualities of this monitor.
The built-in display is a 19" TFT SXGA display with 1280 x 1024 resolution and
300 cd/m
is made of special glass and protects the display from destruction of mechanical
manner, for example get dirty or scratches at the display surface. The
representation quality of the display is optimised also by the antireflection property
of the protection pane.
The monitor can be optionally equipped with a touchscreen.
The KFM19_e comes with VGA (analog), DVI (digital), S-Video (analog),
Composite-video (analog) signal inputs and provides therewith compatibility with
the existing and the future computer-generation.
The KFM19_e can be alternatively equipped with an AC or a DC power supply
unit. The supply voltage range is indicated on the type label. The type label is
located on the back of the unit.
2
luminance (brightness). The protection pane built in front of the display
Fig. 1: KFM_19e – Frontal installed controls
and LED indicator
(shown as panelmount version)
Fig. 1a: KFM_19e – Laterally installed
controls and front side installed LED
(shown as panelmount version)
When installing and switching on the monitor, make sure that
the air openings at the bottom and upper side of the device
(behind the front panel) are not obstructed by objects.
10 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 12
Product Description
Front Panel
The front plate of the KFM19_e is available alternatively as 19" front plate or in
panelmount version.
The 19" front plate version is suitable for the installation of the monitor in
19" industrial cabinets. Therefore are available four mounting holes.
The panelmount version is suitable for the installation of the monitor in an
instrument panel or other cabinets. Therefore at the rear side of the front plate are
available eight threaded studs.
Depending on the ordered KFM19_e configuration at the front side are located the
control elements of the on screen displays (OSD), the “On/Off” button with the
“Status LED” (refer to the “
plate and the 19" display with the protection pane or touchscreen (optional).
The protection class IP 65 is ensured at the front side of the monitor.
Controls and LED Indicator” section), the 19" front
2 1
3
Fig. 2: KFM19_e – Front side (shown as panelmount front plate version)
1 Front panel
2 19” display with protection plate or
touchscreen (optional)
3 Controls and LED Indicator
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 11
Page 13
Product Description
Display
The built-in display is a 19" TFT SXGA display with a resolution of 1280 x 1024
2
and 300 cd/m
of luminance (brightness).
In front of the display is installed a glass protection pane with antireflection
properties. This protects the display surface from dirt and scratches also. The
technical specifications of the built-in display are specified in the “
Technical Data”
chapter.
Display with Touchscreen
The KFM19_e can be optionally equipped with a resistive touchscreen. The
installed touchscreen is a 4-wire resistive touchscreen. The terminal configuration
of the touchscreen can alternatively be an USB or a COM interface. The
touchscreen is connected by means of supplied cables via the
COM (RS232) or USB interface to an external PC with corresponding interface.
The display surface of the KFM19_e is also mechanically protected through the
touchscreen. The touchscreen registers contact of a finger or a pen and moves
the mouse pointer. This functions only under integration of the necessary
software (refer to the “
You get the corresponding touchscreen driver for your operating system on a
storage media (CD-ROM).
Touchscreen Software Installation” chapter).
Do not use a hard or a pointed object to operate the touchscreen,
since it can damage the touchscreen surface.
12 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 14
Product Description
Controls and LED Indicator
At the front plate are situated the control buttons of the On Screen Display (OSD),
the “On/Off” button and the “Status LED”.
The keys of the OSD and the “On/Off” button can be optionally
attached to the right side (rear-mounted) of the monitor (refer to
Fig. 3a). For this device configuration the “Status LED” is installed
at the front side.
Fig. 3: KFM_19e – Controls and LED indicator at the
front side
Fig. 3a: KFM_19e – Laterally
installed controls
2
1
Fig. 4: Controls and LED indicator
3 4 5 6
1
On/Off button
2
Status LED
3
Select button
4
Down button
5
Up button
6
Menu button
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 13
Page 15
Product Description
“On/Off” Button and Status LED
“On/Off”
Button
Status LED
(green)
Status LED
(orange)
Press this button, in order to switch on or off the monitor
KFM19_e.
Even if you switch the monitor off with the “On/Off” button, a
standby voltage is further present in the device.
The unit is complete disconnected from the power source, only
when the power cord is disconnected from the power source.
Therefore the power cord and its connectors must always
remain easily accessible.
Lights up green when the device is switched on by pressing of
the “On/Off” button and a video signal is present at the selected
video input.
Prerequisite:
The power cord must be connected to a corresponding power
source.
Lights up orange, when the monitor is switched off or no video
signal is present at the selected video input.
Prerequisite:
The power cord must be connected to a corresponding power
source.
If this LED does not light up after turning on the device, then
you must check the main power source and the presence of the
video signal at the monitor video signal input.
On Screen Display Buttons
The OSD buttons allow you to select, to scroll, to install in the OSD main menu or
OSD submenu (refer to the “
14 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
On Screen Display (OSD)” chapter.
Page 16
Product Description
Left Side
The interfaces and the power plug (AC or DC) are located at the left side of the
monitor.
1
2
3
4
5
6
Fig. 5: KFM19_e
Left side (with AC power plug)
Fig. 5a: KFM19_e
Left side (with DC power plug)
1 DVI-D (digital) interface
2 VGA (analog) interface
3 C-Video (analog) interface
4 S-Video (analog) interface
5 Touchscreen terminal (USB or COM)
(shows with serial touchscreen
interface)
6 AC or DC power plug (depending on
the ordered version)
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 15
Page 17
Product Description
Interfaces
The following interfaces with standard pin assignments are available:
❏ VGA (analog) input
❏ DVI-D (digital) input
❏ S-Video (analog) input
❏ C-Video (Composite Video) (analog) input
❏ USB / COM interface as the touchscreen terminal
You can connect one corresponding signal source to each video
interface at the same time. By means of the OSD Menu function
“Select” you can select which of the signal source shall be
represented on the display.
VGA Input
The VGA input is a 15-pin D-SUB connector (female), and allows you to connect
an analog graphics card using the supplied VGA cable connector. The industrial
LCD monitor KFM19_e supports at this interface data transfer with up to a
resolution of 1280 x 1024, 85 Hz (SXGA) and Sync-On-Green (SOG).
DVI-D Input
This input is configured as a DVI-D “digital” (female) interface. This interface
supports digital data transfer.
The industrial LCD monitor KFM19_e supports at this interface data transfer with
up to a resolution of 1280 x 1024 (SXGA).
16 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 18
Product Description
S-Video Input
The S-Video input is a 4 pin Mini DIN connector (female), and allows you to
connect external analog signal sources as e.g. DVD or video player.
The industrial LCD monitor KFM19_e supports at this interface TV pictures format
PAL (768 x 576), NTSC (640 x 480) and SECAM.
Composite-Video Input
The Composite-Video input is a cinch connector (yellow, female), and allows you
to connect external analog signal sources as e.g. DVD or video player.
The industrial LCD monitor KFM19_e supports at this interface TV pictures format
PAL (768 x 576), NTSC (640 x 480) and SECAM.
USB / COM Touchscreen Terminal
This interface is available (as an USB or serial COM interface) only
if the industrial LCD monitor KFM19_e is equipped with
touchscreen.
Depending on the ordered configuration of the touchscreen connector this
interface is provided as:
❏ USB interface (version 1.1, type A, female) or as
❏ Serial (COM) interface (9-pin D-SUB socket), configured as RS232.
Power Plug
The power plug is an AC or a DC inlet connector (depending on the ordered
version) and allows the connection to the corresponding power source via the
power cord (only AC cord is supplied).
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 17
Page 19
Product Description
Rear Side
At the rear side of the KFM19_e are the threaded studs (available only at
panelmount front plate version) and the rubber seal.
1
2
1
1
Fig. 6: Rear side of the KFM19_e (shown as panelmount front plate version)
1
Threaded studs metric (available
only at panelmount front plate
version)
2
Rubber seal
1
18 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 20
Product Description
Air Openings
Behind the front plate, at the housings upper and bottom side are the air
openings.
Fig. 7: Air openings (top side) Fig. 8: Air openings (bottom side)
When installing and switching on the monitor, make sure that
the air openings at the bottom and upper side of the device
(behind the front panel) are not obstructed by objects.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 19
Page 21
Product Description
On Screen Display (OSD)
Over the On Screen Display (OSD) can be installed the features, as OSD position
and time, brightness, contrast, color, sharpness and others.
Some of these menus have sub-menus.
The push buttons allow you to select, to scroll, to install in the OSD main menu or
OSD-submenu.
Operation of the OSD Menu
1. Press <Menu> to display the main-menu.
2. The buttons <Up> and <Down> allows moving between the functions of the
main-menu by use of.
3. Press the button <Menu> to choose a main-menu function.
4. The buttons <Up> and <Down> allow moving between the sub-function.
5. Press the button <Menu> to choose a sub menu function.
6. The button <Up> (to increase) and the button <Down> (to decrease) allows
the adjustment of the sub-menu values.
7. Press the button <Menu> to choose the sub menu values.
8. To save a new setting, press the button <Menu> of the KFM19_e.
9. Press the button <Select> to leave the sub-menu.
10. Press the button <Select> to leave the main-menu.
The OSD menu and the possible settings are described in the
provided “KFM - OSD Menu Description” documentation.
20 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 22
Product Description
Power Supply
The KFM19_e can be optionally equipped with an AC PSU or a DC PSU.
The supply voltage range is indicated on the type label. The type label is located
on the rear of the unit.
System
Version
KFM19_e - A AC Power Supply 100 - 240 VAC
KFM19_e - B DC Power Supply 20 - 34 VDC
The suffix “-A” on the type label (System Version, KFM19_e-A) of
the system stands for the marking of the Kontron-devices, which
are equipped with an AC power supply unit.
The suffix “-B” on the type label (System Version, KFM19_e-B) of
the system stands for the marking of the Kontron-devices, which
are equipped with a DC power supply unit.
Integrated
PSU
Input
50 - 60 Hz
max. 0.6 A
max. 2.3 A
Power Cord Connection
Please observe the hints described in the chapter “
Instructions
”.
Safety
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 21
Page 23
Product Description
AC Connection
AC-power plug
Fig. 9: AC power plug
1. Connect the supplied AC power cord into the system AC power plug.
2. Connect the other end of the AC power cord into a corresponding outlet.
Use the power cord suitable for the power supply in your country.
Do not remove or alter the grounding prong on the power cord. In
situations where a two-slot receptacle is present, have it replaced
with a properly grounded three-prong grounding type receptacle.
22 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 24
Product Description
DC Connection
For the DC connection prepare the connecting wires using the supplied Phoenix
plug terminal.
The length of the DC connecting wires may not exceed 10 m.
DC Phoenix
connector
–
+
DC Phoenix
connector with
plug terminal
–
+
Fig. 10: DC Phoenix connector Fig. 10a: DC Phoenix connector with plug
terminal (supplied)
1. Cut the required length of two isolated wires (∅ up to 1.5 mm
2
).
2. Strip each end 5 –7 mm.
3. Twist the striped wire ends and tin it with solder.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 23
Page 25
Product Description
4. Loosen the two slotted pan head screws of the DC plug terminal far enough
so that you can insert the end of the power cord.
1 2
3
4
Fig. 11: Phoenix plug terminal with positive and negative voltage wire (example)
1 Phoenix plug terminal
Slotted pan head screws
2
3
Negative voltage wire (black)
Positive voltage wire (red)
4
5. Insert the negative and positive voltage wire into the corresponding clamp of
the Phoenix plug terminal. Make sure that you have the right polarity of the
connection (see
Fig: 10a).
6. Fasten the screws to secure the negative and positive voltage wire into the
clamps of the plug terminal.
The second end of each wire will be prepared as required for the
connection to the DC power supply.
Connect the KFM19_e to the DC power source as follows:
1. Plug the one end of the DC cable connection (Phoenix plug terminal) to the
Phoenix plug of the KFM19_e.
2. Connect the other end of the DC cable connector to a corresponding DC
power source.
24 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 26
Installation Instructions
Installation Instructions
Please observe the described hints in the “
chapter and the specification listed in the “
chapter.
Instruction for Mounting
Please take into consideration the needed free space on the
interface side, before you install the monitor into an industrial
cabinet, an instrument panel or other cabinets.
For detailed information about the available interfaces refer to the
section “
Important Instructions!
The installation of the KFM19_e may only be carried out by
qualified personnel.
Ensure there is sufficient air circulation around the device when
installing the KFM19_e.
The openings for the device cooling (on upper and bottom side)
must not be obstructed. Blocked air openings, can cause
overheat of the monitor.
When installing KFM19_e into an industrial cabinet, leave at least
5 cm of free space around the unit to prevent the device from
possibly overheating!
The 19” industrial cabinet must stand firmly in place.
If further stabilisation is necessary, then bolt the industrial cabinet
to the floor or anchor it on the wall.
The voltage feeds must not be overloaded. Adjust the cabling and
the external overcharge protection to correspond with the
electrical values indicated on the type label.
The type label is located on the left side of the monitor.
Interfaces”.
Safety Instructions”
Technical Data”
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 25
Page 27
Installation Instructions
Panelmount Version
If you install the panel version of the KFM19_e into an instrument panel or other
cabinets, use the eight threaded M4 metric studs on the rear side of the front
plate.
For the panel assembly cut a window and pre-drill holes according
monitor must be attached firmly with eight M4 metric nuts.
The contact surface with the rubber seal must be clean and flush.
∅7 (8x)
Fig. 12: Hole pattern for the KFM19_e mounting
(all values in mm)
Fig. 12. The
Rackmount Version
If you install the rackmount version of the KFM19_e into a 19" industrial cabinet,
use the four mounting holes of the front plate.
The system has a height of 9U and must be secured with four screws in the
19" industrial cabinet.
26 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 28
Monitor Connecting and Turning On
Monitor Connecting and Turning On
The industrial LCD monitor KFM19_e can be connected to IBM PC systems
equipped with corresponding graphics capability.
1. Connect the PC system’s video signal output interface to the video signal
input of the KFM19_e using the supplied video signal cable (depending on
your ordering).
2. If your KFM19_e is equipped with touchscreen (with COM or USB connection)
you have to connect the touchscreen to the corresponding interface of the PC
system using the supplied touchscreen cable connector.
3. Connect the power cord as described in the “Power Cord Connection”
chapter.
4. Push the “On/Off” button to turn on the monitor.
The PC should be set to an appropriate graphics mode that has the
same resolution with the LCD panel to have a clear screen image.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 27
The colour representation of the image on each monitor can differ
by physically causes and is dependent on the video signal
source.
If you prefer another colour temperature or want to adapt the
colour representation of images on two monitors, you have to
install these features in the OSD menu under “Color”.
Execute these settings only after reaching of the full operating
temperature of the monitor (approx. 30 minutes).
When the screen is not in use, it must be turned off or the pattern
must be frequently changed by a screen saver.
If it displays the same pattern for a long period of time, brightness
down or “image sticking” may develop due to the structure of LCDisplays.
Page 29
Monitor Connecting and Turning On
Touchscreen Software Installation
The driver for Windows® 2000 / XP operating system for the touchscreen
installation is included on the CD-ROM supplied.
Insert the CD-ROM, double-click on “setup.exe” to start the installer. During the
installation sequence, some screens will appear (“Welcome”, “Select Folder”,
“Select Destination Directory”, “Number of devices”).
Follow the instructions displayed on the screen and select the type
of the connection for the touchscreen controller (serial or USB).
Selecting the Touchscreen Controller
During the installation, the screen for selecting the controller will appear. Select
the serial or USB connection of the touch controller, depending on the ordered
KFM19_e configuration.
For serial connection, select: [DMC TSC-10 Series, Serial].
For USB connection, select: [DMC TSC-10 Series, USB].
Fig. 13: Selecting the touchscreen controller
28 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 30
Monitor Connecting and Turning On
If you choose [DMC TSC-10 Series, Serial], the “Serial port” setting window
appears. Choose the corresponding port from popup menu.
Fig. 14: Selection of the corresponding port
After installing the touchscreen driver, be sure to restart your
computer to load and activate the touchscreen driver. Afterwards
the calibration of the touchscreen has to be carried out.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 29
Page 31
Monitor Connecting and Turning On
Calibrating the Touchscreen
After the installation of the touchscreen driver, you have to calibrate the
touchscreen. The calibration serves two purposes:
❏ Sets the active area of the touchscreen.
❏ Aligns the active area of the touchscreen to the screen’s image.
Before you calibrate the touchscreen, let the KFM19_e warm up for
30 minutes.
Calibration aligns the active touch-sensitive area of the touchscreen with the
image on the display. Calibration also determines the edges of the screen’s image
and locates the center of the touchscreen.
If the touchscreen is not calibrated properly, the active area of the touchscreen
may not be aligned with the screen’s image.
To calibrate the touchscreen, open the touchscreen control panel program, and
then select “Calibration”. Follow the instructions displayed on the screen. Fore
more information on calibration, refer to the user documentation enclosed on the
supplied CD with the touchscreen driver.
Do not use a hard or a pointed object to operate the touchscreen,
since it can damage the touchscreen surface.
30 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 32
Monitor Connecting and Turning On
You can adjust the calibration of the touchscreen by running the program at
[Start]
→ [Program] → [UPDD] → [Control setting]. Use your finger to touch the
crosshair on the light gray screen. Touching the crosshair lets it appear at another
position. Similarly, touch that position too.
Fig. 15: Touchscreen displaying information
After calibrating the touchscreen you can test the alignment by pressing the
“Test
” button to view the tracking accuracy.
Whenever you change the resolution, you have to calibrate the
touchscreen.
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 31
Page 33
Maintenance and Prevention
Maintenance and Prevention
Kontron Embedded Computers systems only require minimal maintenance and
care to keep them operating correctly.
❏ Occasionally wipe the system with a soft dry cloth.
❏ Remove persistent dirt by use of a soft, slightly damp cloth (use only a mild
detergent).
Use no abrasives, abrasion sponges, steel wool, metal threads, or
solvent like alcohol, acetone, washing gasoline to clean the
displays protection pane or the surface of the touchscreen.
32 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 34
Technical Data
Technical Data
TFT LCD Display
Touchscreen
(optional)
Interfaces At the left side (rear mounted):
Controls
LED Indicator At the front side:
Plug & Play
Compatibility
AC or DC Power Plug At the left side (rear mounted)
Backlight Lifetime
Protection Class IP65 frontal
Diagonally (Size)
active area
Resolution 1280 x 1024
Pixel Pitch 0.294 mm x 0.294 mm
Color depth /Colors 16 M colors
Backlight 4x CCFL
Brightness 300 cd/m
Viewing angle (r / l / u / d) 85° / 85° / 85° / 85°
Contrast ratio 700:1
Type: 4-wire resistive
with COM (RS232) or USB connector (optional)
1x VGA (analog) input
1x DVI-D (digital) input
1x S-Video (analog) input
1x Composite Video(analog) input
At the front side or optional right side (rear mounted):
1x “On/Off” button
for image representation adjustment on-screen:
1x Menu button of OSD
1x Up button of OSD
1x Down button of OSD
1x Select button of OSD
1x Status LED
VESA DDC1/2B EDID Ver. 1.3
40,000 h
19”
(376.0 x 301.1 mm)
2
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 33
Page 35
Technical Data
Mechanical Specifications
Dimensions Panelmount 19" Front plate
H x W x D
Front Plate:
Material
Chassis
Height 372 mm (14.646") 372 mm (14.646")
Width 427.5 mm (16.831") 427.5 mm (16.831")
Depth 70 mm (2.756") 70 mm (2.756")
Material steel zinc-plated steel zinc-plated
Weight
431 x 482.6 x 5 (mm)
16.97" x 19" x 0.197"
steel zinc-plated
Frontal: black powder coated
approx. 9.8 kg (21.605 lbs.)
(without packing)
H x W x D
399.2 x 482.6 x 5 mm
9U x 19" x 0.197"
steel zinc-plated
Frontal: black powder coated
approx. 9.8 kg (21.605 lbs.)
(without packing)
Electrical Specifications
System Designation Integrated
PSU
Input
100 - 240 VAC
KFM19_e - A AC Power Supply
KFM19_e - B DC Power Supply
34 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
50 - 60 Hz
max. 0.6 A
20 - 34 DC
max. 2.3 A
Page 36
Technical Data
Environmental Specifications
Operating Temperature
Storage / Transit
temperature
Relative Humidity
(operating)
Humidity (storage) 5 – 85 % (non-condensing)
Operating Altitude 10,000 ft (3,048 m)
Storage / Transit Altitude 40,000 ft (12,191 m)
Operating Shock 15 G, 11 ms duration, half sine
Storage/Transit Shock 30 G, 11 ms duration, half sine
Operating Vibration
Storage / Transit Vibration
0 … +50 °C
(32 … 122
–20 … +60 °C
(–4 … 140 °F )
20 – 85 % (non-condensing)
10 – 58 Hz, ± 0.075 mm
58 – 500 Hz, 1.0 G
10 – 58 Hz, ± 0.15 mm
58 – 500 Hz, 2.0 G
°F
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 35
Page 37
Technical Data
CE Directives and Standards
CE Directives
Low Voltage Directive
(Electrical Safety)
EMC Directive 89/336/EEC
Electrical Safety Standards
EUROPE EN 60950-1: 2000
EMC Standards
EUROPE
USA FCC 47 CFR Part 15, Class A
73/23/EEC
Emission:
EN 61000-6-4: 2001
Immunity:
EN 61000-6-2: 2001
36 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 38
Technical Appendix – Interfaces
Technical Appendix – Interfaces
The following tables show the plug assignments for the external connections of
the KFM19_e.
Low-active signals are indicated by a minus sign.
VGA Connector
Pin Signal Name 15-pin D-SUB Socket (female)
1 red
2 green
3 blue
4 4 is NC
5–8 GND
9 Fused VCC
10 GND
11 NC
12 DDC Data
13 HSYNC
14 VSYNC
15 DDC Clock
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 37
Page 39
Technical Appendix – Interfaces
DVI-D Connector
Pin Signal Name Description DVI-D Connector
(female)
1 TMDS2– Differential TMDS Data 2–
2 TMDS2– Differential TMDS Data 2+
3 GND TMDS Shield
4–5 NC Reserved for future use
6 DVI_SCL DDC EDID data clock
7 DVI_SDA DDC EDID data
8 DVI_VS Analog VSYNC
9 TMDS1– Differential TMDS Data 1–
10 TMDS1+ Differential TMDS Data 1+
11 GND TMDS Shield
12–13 NC Reserved for future use
14 DVI_5V 5V / 100mA Power Supply
15 GND Ground
16 DISPDET Hot Plug Detection
17 TMDS0– Differential TMDS Data 0–
18 TMDS0+ Differential TMDS Data 0+
19 GND TMDS Shield
20–21 NC Reserved for future use
22 GND TMDS Shield
23 TMDSSCL– Differential TMDS Clock–
24 TMDSSCL+ Differential TMDS Clock +
38 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 40
Technical Appendix – Interfaces
S-Video Connector
Pin Signal Name Description 4-pin Mini-DIN Connector
(female)
1 GND Ground
2 GND Ground
3 Y Luminance
4 C Chrominance
C-Video (Composite) Connector
Pin Signal Name Description Cinch Connector (yellow)
(female)
1 GND Ground
2 CVBS
Composite video
signal
USB Touchscreen Connector
Pin Signal Name 4 pin USB Socket
Type A Version 1.1
1 VCC
2 Data–
3 Data+
4 GND
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 39
Page 41
Technical Appendix – Interfaces
Serial Touchscreen Connector (RS232)
Pin Signal Name 9-pin D-SUB Socket
1 DCD (Data Carrier Detect)
2 RXD (Receive Data)
3 TXD (Transmit Data)
4 DTR (Data Terminal Ready)
5 GND (Signal Ground
6 DSR (Data Set Ready)
7 RTS (Request to Send)
8 CTS (Clear to Send)
9 RI (Ring Indicator)
40 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Page 42
Technical Support
Technical Support
For technical support, please contact our Technical Support department.
Tel: +49 (0)9461 950-104
Fax: +49 (0)9461 950-200
e-mail:
Make sure you have the following information on hand when you call:
Be ready to explain the nature of your problem to the service technician.
If you have questions about Kontron Embedded Computers or our products and
services, you may reach us at the aforementioned numbers, or at:
www.kontron.com or by writing to:
Kontron Embedded Computers GmbH
Oskar-von-Miller-Str. 1
85386 Eching
support@kontron.com
• the unit part id number (P/No #),
• and the serial number (S/No #) of the unit (provide the serial
number found on the type label, placed on the rear side of the system).
19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10) 41
Page 43
Technical Support
Returning Defective Merchandise
Before returning any merchandise, please:
1. Contact our Customer Service department
to obtain an RMA (Return Material Authorization) number.
Fax: (+49) 8165-77 412
e-mail:
2. Make sure that you receive an RMA number from Kontron Embedded
Computers-Service before returning any merchandise. Clearly write or mark
this number on the outside of the package you are returning.
3. Describe the device failure behavior.
4. When ret urning goods, include the name and telephone number of a person
whom we can contact for further explanations if necessary. Where applicable,
always include all duty papers and invoice(s) associated with the item(s) in
question.
5. When ret urning a unit:
• Ensure that the unit is properly packed in the original box.
• Include a copy of the RMA form.
service@kontron.com
42 19" Industrial LCD Monitor KFM19_e – User’s Manual (Version 1.10)
Loading...