Kontron KBox E-200, KBox M-100, KBox M-200 User Manual



USER GUIDE

www.kontron.com

// 1

KBox E-200 Series

Doc. User Guide, Rev. 1.0

Doc. ID: [To be Determined]

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 2

This page has been intentionally left blank

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 3



KBOX E-200 SERIES - USER GUIDE

Disclaimer

Kontron would like to point out that the information contained in this user guide may be subject to alteration,
particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee
on the part of Kontron with respect to technical processes described in the user guide or any product characteristics
set out in the user guide. Kontron assumes no responsibility or liability for the use of the described product(s),
conveys no license or title under any patent, copyright or mask work rights to these products and makes no
representations or warranties that these products are free from patent, copyright or mask work right infringement
unless otherwise specified. Applications that are described in this user guide are for illustration purposes only.
Kontron makes no representation or warranty that such application will be suitable for the specified use without
further testing or modification. Kontron expressly informs the user that this user guide only contains a general
description of processes and instructions which may not be applicable in every individual case. In cases of doubt,
please contact Kontron.

This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the
express written permission of Kontron. Kontron points out that the information contained in this user guide is
constantly being updated in line with the technical alterations and improvements made by Kontron to the products
and thus this user guide only reflects the technical status of the products by Kontron at the time of publishing.

Brand and product names are trademarks or registered trademarks of their respective owners.

©2018 by Kontron AG

Kontron AG

Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
www.kontron.com

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 4

High Risk Applications Hazard Notice

THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE
OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL OR
COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC CONTROL, LIFE
SUPPORT OR LIFE SUSTAINING APPLICATIONS, WEAPONS SYSTEMS, OR ANY OTHER APPLICATION IN A
HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE, OR IN WHICH THE FAILURE OF
PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL OR
ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS").

You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at
your risk. To minimize the risks associated with your products and applications, you should provide adequate design
and operating safeguards. You are solely responsible for compliance with all legal, regulatory, safety, and security
related requirements concerning your products. You are responsible to ensure that your systems (and any Kontron
hardware or software components incorporated in your systems) meet all applicable requirements. Unless otherwise
stated in the product documentation, the Kontron device is not provided with error-tolerance capabilities and cannot
therefore be deemed as being engineered, manufactured or setup to be compliant for implementation or for resale as
device in High Risk Applications. All application and safety related information in this document (including application
descriptions, suggested safety measures, suggested Kontron products, and other materials) is provided for reference
only

.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 5

Revision History

Revision Brief Description of Changes Date of Issue

1.0 Initial Issue 2018-Jan-25

Terms and Conditions

Kontron warrants products in accordance with defined regional warranty periods. For more information about
warranty compliance and conformity, and the warranty period in your region, visit http://www.kontron.com/terms­and-conditions.

Kontron sells products worldwide and declares regional General Terms & Conditions of Sale, and Purchase Order
Terms & Conditions. Visit http://www.kontron.com/terms-and-conditions.

For contact information, refer to the corporate offices contact information on the last page of this user guide or visit
our website

CONTACT US.

Customer Support

Find Kontron contacts by visiting: http://www.kontron.com/support.

Customer Service

As a trusted technology innovator and global solutions provider, Kontron extends its embedded market strengths into
a services portfolio allowing companies to break the barriers of traditional product lifecycles. Proven product
expertise coupled with collaborative and highly-experienced support enables Kontron to provide exceptional peace of
mind to build and maintain successful products.

For more details on Kontron’s service offerings such as: enhanced repair services, extended warranty, Kontron
training academy, and more visit

http://www.kontron.com/support-and-services/services.

Customer Comments

If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact
Kontron support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the
revised user guide on our website.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 6

Symbols

The following symbols may be used in this user guide

DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

NOTICE indicates a property damage message.

CAUTION indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury.

Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60

V) when touching

products or parts of products

. Failure to observe the precautions indicated and/or

prescribed by the law may endanger your life/health and/or result in damage to your

material.

ESD Sensitive Device!
This symbol and title inform that the electronic boards and their components are sensitive

to static electricity. Care must therefore be taken during all handling operations and

inspections of this product in order to ensure product integrity at all times.

HOT Surface!
Do NOT touch! Allow to cool before servicing.

Laser!
This symbol inform of the risk of exposure to laser beam and light emitting devices (LEDs)

from an electrical device. Eye protection per manufacturer notice shall review before
servicing.

This symbol indicates general information about the product and the user guide.

This symbol also indicates detail information about the specific product configuration.

This symbol precedes helpful hints and tips for daily use.

KBox E-200 Series – User Guide, Rev. 1.0

www.kontron.com

// 7

For Your Safety

Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its
compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life
expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are
requested to conform with the following guidelines.

High Voltage Safety Instructions

As a precaution and in case of danger, the power connector must be easily accessible. The power connector is the
product’s main disconnect device.

Warning
All operations on this product must be carried out by sufficiently skilled personnel only.

Electric Shock!
Before installing a non hot-swappable Kontron product into a system always ensure that

your mains power is switched off. This also applies to the installation of piggybacks. Serious
electrical shock hazards can exist during all installation, repair, and maintenance operations
on this product. Therefore, always unplug the power cable and any other cables which
provide external voltages before performing any work on this product.

Earth ground connection to vehicle’s chassis or a central grounding point shall remain
connected. The earth ground cable shall be the last cable to be disconnected or the first
cable to be connected when performing installation or removal procedures on this product.

Special Handling and Unpacking Instruction

ESD Sensitive Device!
Electronic boards and their components are sensitive to static electricity. Therefore, care

must be taken during all handling operations and inspections of this product, in order to
ensure product integrity at all times.

Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is
otherwise protected.

Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not
guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands
or tools. This is most easily done by touching a metal part of your system housing.

It is particularly important to observe standard anti-static precautions when changing piggybacks, ROM devices,
jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the product is not placed
on conductive surfaces, including anti-static plastics or sponges. They can cause short circuits and damage the
batteries or conductive circuits on the product.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 8

Lithium Battery Precautions

If your product is equipped with a lithium battery, take the following precautions when replacing the battery.

Danger of explosion if the battery is replaced incorrectly.

 Replace only with same or equivalent battery type recommended by the manufacturer.
 Dispose of used batteries according to the manufacturer’s instructions.

General Instructions on Usage

In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or
modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received
from Kontron Support as a special handling instruction, will void your warranty.

This product should only be installed in or connected to systems that fulfill all necessary technical and specific
environmental requirements. This also applies to the operational temperature range of the specific board version
that must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.

In performing all necessary installation and application operations, only follow the instructions supplied by the
present user guide.

Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship
the product then re-pack it in the same manner as it was delivered.

Special care is necessary when handling or unpacking the product. See Special Handling and Unpacking Instruction.

Quality and Environmental Management

Kontron aims to deliver reliable high-end products designed and built for quality, and aims to complying with
environmental laws, regulations, and other environmentally oriented requirements. For more information regarding
Kontron’s quality and environmental responsibilities, visit http://www.kontron.com/about-kontron/corporate­responsibility/quality-management.

Disposal and Recycling

Kontron’s products are manufactured to satisfy environmental protection requirements where possible. Many of the
components used are capable of being recycled. Final disposal of this product after its service life must be
accomplished in accordance with applicable country, state, or local laws or regulations.

WEEE Compliance

The Waste Electrical and Electronic Equipment (WEEE) Directive aims to:

 Reduce waste arising from electrical and electronic equipment (EEE)
 Make producers of EEE responsible for the environmental impact of their products, especially when the product

become waste

 Encourage separate collection and subsequent treatment, reuse, recovery, recycling and sound environmental

disposal of EEE

 Improve the environmental performance of all those involved during the lifecycle of EEE

Environmental protection is a high priority with Kontron.
Kontron follows the WEEE directive
You are encouraged to return our products for proper disposal.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 9

Table of Contents

Symbols ................................................................................................................................................................................................................. 6

For Your Safety ................................................................................................................................................................................................... 7

High Voltage Safety Instructions .................................................................................................................................................................. 7

Special Handling and Unpacking Instruction ............................................................................................................................................ 7

Lithium Battery Precautions .......................................................................................................................................................................... 8

General Instructions on Usage ..................................................................................................................................................................... 8

Quality and Environmental Management ................................................................................................................................................ 8

Disposal and Recycling .................................................................................................................................................................................... 8

WEEE Compliance.............................................................................................................................................................................................. 8

Table of Contents............................................................................................................................................................................................... 9

List of Tables ...................................................................................................................................................................................................... 11

List of Figures ..................................................................................................................................................................................................... 11

1/ General Safety Instructions for IT Equipment ......................................................................................................................... 13

1.1. Electrostatic Discharge (ESD) ................................................................................................................................................................ 15

1.1.1. Grounding Methods ................................................................................................................................................................................ 15

1.2. Lithium Battery Replacement ............................................................................................................................................................... 15

2/ Electromagnetic Compatibility ..................................................................................................................................................... 16

2.1. Electromagnetic Compatibility (EU) .................................................................................................................................................... 16

2.2. FCC Statement (USA) ............................................................................................................................................................................... 16

2.3. EMC Compliance (Canada) .................................................................................................................................................................... 16

3/ Shipment and Unpacking ................................................................................................................................................................ 17

3.1. Unpacking .................................................................................................................................................................................................... 17

3.2. Scope of Delivery ...................................................................................................................................................................................... 17

3.2.1. Standard ................................................................................................................................................................................................... 17

3.2.2. Optional Parts ........................................................................................................................................................................................ 17

4/ System Overview ............................................................................................................................................................................... 18

4.1. System Expansion Capabilities ............................................................................................................................................................ 19

4.1.1. System Expansion via SATA Interface ............................................................................................................................................. 19

4.1.2. System Expansion via mSATA Interface ........................................................................................................................................ 19

4.1.3. System Expansion via eSATA Interface.......................................................................................................................................... 19

4.1.4. System Expansion via mPCIe Card Interface ................................................................................................................................ 19

4.1.4.1. System Expansion via SIM Socket ................................................................................................................................................. 19

4.2. Front I/O Panel ......................................................................................................................................................................................... 20

4.2.1. Power Button with LDE ....................................................................................................................................................................... 20

4.2.2. HDD LED .................................................................................................................................................................................................. 20

4.2.3. Wireless LED ........................................................................................................................................................................................... 21

4.2.4. Reset Button ........................................................................................................................................................................................... 21

4.2.5. Line-Out ................................................................................................................................................................................................... 21

4.2.6. Mic-In ........................................................................................................................................................................................................ 21

4.2.7. Line-In ....................................................................................................................................................................................................... 21

4.2.8. S/PFIF ....................................................................................................................................................................................................... 21

4.2.9. USB 3.0 ..................................................................................................................................................................................................... 21

4.2.10. USB 2.0.................................................................................................................................................................................................... 21

4.2.11. eSATA ....................................................................................................................................................................................................... 21

4.3. Rear I/O Panel .......................................................................................................................................................................................... 22

4.3.1. DC Jack ...................................................................................................................................................................................................... 22

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 10

4.3.2. HDMI ......................................................................................................................................................................................................... 22

4.3.3. GbE ............................................................................................................................................................................................................ 22

4.3.4. USB 3.0 .................................................................................................................................................................................................... 23

4.3.5. RS232/422/485 ................................................................................................................................................................................... 23

4.3.6. External Power Switch ....................................................................................................................................................................... 23

4.3.7. Antenna ................................................................................................................................................................................................... 23

4.4. Internal View ............................................................................................................................................................................................. 24

4.4.1. DDR3L SO-DIMM Memory Socket ................................................................................................................................................... 24

4.4.2. SATA Connector.................................................................................................................................................................................... 24

4.4.3. mSATA Socket ....................................................................................................................................................................................... 25

4.4.4. mPCIe Socket......................................................................................................................................................................................... 25

4.4.4.1. System Expansion via SIM Socket ............................................................................................................................................... 25

5/ Accessing Internal Components .................................................................................................................................................. 26

5.1. Opening and Closing the KBox E-200 Series ................................................................................................................................... 27

5.1.1. Installing an HDD / SSD ....................................................................................................................................................................... 28

5.1.2. Installing an mSATA SSD .................................................................................................................................................................... 29

5.1.3. Installing an mPCIe expansion card ................................................................................................................................................ 29

5.1.4. Installing the SIM card ........................................................................................................................................................................ 29

6/ Thermal Considerations .................................................................................................................................................................. 31

6.1. Available Processors................................................................................................................................................................................ 31

6.2. Convection Cooling .................................................................................................................................................................................. 31

6.3. System Clearance ..................................................................................................................................................................................... 31

6.4. Maximum Temperatures ....................................................................................................................................................................... 31

6.5. Third Party Components ........................................................................................................................................................................ 31

7/ Installation Instructions ................................................................................................................................................................. 32

7.1. System Mounting ..................................................................................................................................................................................... 33

7.2. DC Power Connection ............................................................................................................................................................................. 36

8/ Starting Up........................................................................................................................................................................................... 37

8.1. Connecting to DC Power Supply .......................................................................................................................................................... 37

8.2. Operating System and Hardware Component Drivers ............................................................................................................... 38

9/ Maintenance and Cleaning ............................................................................................................................................................ 39

10/ Technical Specifications ................................................................................................................................................................. 40

10.1. Mechanical Specifications .................................................................................................................................................................... 41

10.1.1. Mechanical Drawing ............................................................................................................................................................................ 41

10.2. Environmental Conditions .................................................................................................................................................................. 42

10.3. Standards and Certifications ............................................................................................................................................................. 42

11/ Standard Interfaces – Pin Assignments ................................................................................................................................... 43

11.1.1. DC Jack ...................................................................................................................................................................................................... 43

11.1.2. Ethernet Connectors ........................................................................................................................................................................... 43

11.1.3. USB 3.0 Port ........................................................................................................................................................................................... 43

11.1.4. USB 2.0 Port ........................................................................................................................................................................................... 44

11.1.5. HDMI Connector ................................................................................................................................................................................... 44

11.1.6. RS232/422/485 Serial Port ............................................................................................................................................................. 45

11.1.7. Line-Out Connector ............................................................................................................................................................................. 45

11.1.8. Mic-In Connector ................................................................................................................................................................................. 45

11.1.9. Line-In Connector ................................................................................................................................................................................ 45

11.1.10. eSATA Connector................................................................................................................................................................................ 47

11.1.11. External Power Switch Wafer ........................................................................................................................................................ 47

12/ uEFI BIOS .............................................................................................................................................................................................. 48

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 11

12.1. Starting the uEFI BIOS ........................................................................................................................................................................... 48

12.2. Setup Menus ............................................................................................................................................................................................ 49

12.2.1. Main Setup Menu ................................................................................................................................................................................ 49

12.2.2. Advanced Setup Menu ....................................................................................................................................................................... 51

12.2.3. Power Setup Menu .............................................................................................................................................................................. 61

12.2.4. Boot Setup Menu ................................................................................................................................................................................ 63

12.2.5. Security Setup Menu ......................................................................................................................................................................... 64

12.2.5.1. Remember the password ............................................................................................................................................................. 65

12.2.6. Save & Exit Setup Menu ................................................................................................................................................................... 66

Appendix A: List of Acronyms ..................................................................................................................................................................... 67

About Kontron .................................................................................................................................................................................................. 68

List of Tables

Table 1: Technical Specifications ................................................................................................................................................................ 40

Table 2: Mechanical Specifications ............................................................................................................................................................ 41

Table 3: Environmental Conditions ........................................................................................................................................................... 42

Table 4: Standards and Certifications ...................................................................................................................................................... 42

Table 5: DC Jack (see Figure 2, pos.1) ........................................................................................................................................................ 43

Table 6: Ethernet Connector (see Figure 2, pos. 3) .............................................................................................................................. 43

Table 7: USB 3.0 Port (see Figure 1, pos. 9 & Figure 2, pos.4) ........................................................................................................... 43

Table 8: USB 2.0 Port (see Figure 1, pos. 10) ........................................................................................................................................... 44

Table 9: HDMI Connector (see Figure 2, pos. 2) ..................................................................................................................................... 44

Table 10: RS232/422/485 Serial Port (see Figure 2, pos. 5) ............................................................................................................. 45

Table 11: Line-Out Connector (see Figure 2, pos. 5) ............................................................................................................................. 45

Table 12: Mic-In Connector (see Figure 2, pos. 6) ................................................................................................................................. 45

Table 13: Line-In Connector (see Figure 2, pos. 7) ................................................................................................................................ 45

Table 14: eSATA Connector (see Figure 1, pos. 11) ................................................................................................................................. 47

Table 15: External Power Switch Wafer (see Figure 2, pos.6) .......................................................................................................... 47

Table 16: Navigation Hot Keys Available in the Legend Bar .............................................................................................................. 48

Table 17: Main Setup Menu Sub-Screens and Functions ................................................................................................................... 49

Table 18: List of Acronyms ........................................................................................................................................................................... 67

List of Figures

Figure 1: Front I/O Panel ................................................................................................................................................................................ 20

Figure 2: Rear I/O Panel ................................................................................................................................................................................. 22

Figure 3: Ethernet LED Status...................................................................................................................................................................... 22

Figure 4: Internal view (without cover) ................................................................................................................................................... 24

Figure 5: Descrewing the access cover of the KBox E-200 Series .................................................................................................. 27

Figure 6: Installing an HDD/ SSD ................................................................................................................................................................ 28

Figure 7: Installing the SIM card ................................................................................................................................................................. 30

Figure 8: Optional VESA mounting kit for KBox E-200 Series ........................................................................................................... 33

Figure 9: Hole pattern of base mounting bracket for KBox E-200 Series .................................................................................... 33

Figure 10: Securing the base mounting bracket .................................................................................................................................... 34

Figure 11: Securing the hooked mounting bracket onto the KBox E-200 Series ......................................................................... 34

Figure 12: Securing the KBox E-200 Series onto the mounting surface ....................................................................................... 34

Figure 13: Mechanical Drawing .................................................................................................................................................................... 41

Figure 14: BIOS Main Menu Screen System Data and Time ............................................................................................................... 50

Figure 15: BIOS Advanced Menu .................................................................................................................................................................. 52

Figure 16: BIOS Advanced Menu - Display Configuration ................................................................................................................... 53

Figure 17: BIOS Advanced Menu - Super IO Configuration ................................................................................................................. 54

Figure 18: BIOS Advanced Menu - Super IO Configuration - Serial Port 1 Configuration ......................................................... 54

Figure 19: BIOS Advanced Menu - Super IO Configuration - Serial Port 2 Configuration ......................................................... 55

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 12

Figure 20: BIOS Advanced Menu - CPU Advanced Configuration .................................................................................................... 56

Figure 21: BIOS Advanced Menu - SATA Configuration ........................................................................................................................ 57

Figure 22: BIOS Advanced Menu - USB Configuration ......................................................................................................................... 58

Figure 23: BIOS Advanced Menu - Intel® Rapid Start Technology .................................................................................................. 59

Figure 24: BIOS Advanced Menu - H/W Monitor .................................................................................................................................. 60

Figure 25: BIOS Power Setup Menu ............................................................................................................................................................ 61

Figure 26: BIOS Power Setup Menu - WatchDog Timer Configuration .......................................................................................... 62

Figure 27: BIOS Boot Setup Menu ............................................................................................................................................................... 63

Figure 28: BIOS Security Setup Menu ....................................................................................................................................................... 64

Figure 29: BIOS Save & Exit Setup Menu ................................................................................................................................................. 66

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 13

1/ General Safety Instructions for IT Equipment

Please read this chapter carefully and take careful note of the instructions, which have been
compiled for your safety and to ensure to apply in accordance with intended regulations. If
the following general safety instructions are not observed, it could lead to injuries to the
operator and/or damage of the product; in cases of nonobservance of the instructions
Kontron is exempt from accident liability, this also applies during the warranty period.

The product has been built and tested according to the basic safety requirements for low voltage (LVD) applications
and has left the manufacturer in safety-related, flawless condition. To maintain this condition and also to ensure safe
operation, the operator must not only observe the correct operating conditions for the product but also the following
general safety instructions:

 The product must be used as specified in the product documentation, in which the instructions for safety for the

product and for the operator are described. These contain guidelines for setting up, installation and assembly,
maintenance, transport or storage.

 The on-site electrical installation must meet the requirements of the country's specific local regulations.
 If a power cable comes with the product, only this cable should be used. Do not use an extension cable to connect

the product.

 To guarantee that sufficient air circulation is available to cool the product, please ensure that the ventilation

openings are not covered or blocked. If an air filter is provided, this should be cleaned regularly. Do not place the
system close to heat sources or damp places. Make sure the system is well ventilated.

 Only devices or parts which fulfill the requirements of SELV circuits (Safety Extra Low Voltage) as stipulated by

IEC 60950-1 may be connected to the available interfaces.

 Before opening the device, make sure that the device is disconnected from the mains.
 Switching off the device by its power button does not disconnect it from the mains. Complete disconnection is

only possible if the power cable is removed from the wall plug or from the device. Ensure that there is free and
easy access to enable disconnection.

 The device may only be opened for the insertion or removal of add-on cards (depending on the configuration of

the system). This may only be carried out by qualified operators.

 If extensions are being carried out, the following must be observed:

 All effective legal regulations and all technical data are adhered to.
 The power consumption of any add-on card does not exceed the specified limitations.

 The current consumption of the system does not exceed the value stated on the product label.
 Only original accessories that have been approved by Kontron can be used.
 Please note: safe operation is no longer possible when any of the following applies:

 The device has visible damages.

 The device is no longer functioning.

In this case the device must be switched off and it must be ensured that the device can no longer be operated.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 14

Additional safety instructions for DC power supply circuits

 To guarantee safe operation of devices with DC power supply voltages larger than 60 volts DC or a power

consumption larger than 240 VA, please observe that:

 the device is set up, installed and operated in a room or enclosure marked with “RESTRICTED ACCESS”, if

there are no safety messages on product as safety signs and labels on the device itself.

 no cables or parts without insulation in electrical circuits with dangerous voltage or power should be

touched directly or indirectly

 a reliable protective earthing connection is provided

 a suitable, easily accessible disconnecting device is used in the application (e.g. overcurrent protective

device), if the device itself is not disconnectable

 a disconnect device, if provided in or as part of the equipment, shall disconnect both poles simultaneously

 interconnecting power circuits of different devices cause no electrical hazards
 A sufficient dimensioning of the power cable wires must be selected – according to the maximum electrical

specifications on the product label – as stipulated by EN60950-1 or VDE0100 or EN60204 or UL508 regulations.

 The devices do not generally fulfill the requirements for "centralized DC power systems“ (UL 60950-1, Annex NAB;

D2) and therefore may not be connected to such devices!

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 15

1.1. Electrostatic Discharge (ESD)

A sudden discharge of electrostatic electricity can destroy static-sensitive devices or
micro-circuitry.

Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the
following precautions:

1. Transport boards in ESD-safe containers such as boxes or bags.

2. Keep electrostatic sensitive parts in their containers until they arrive at the ESD-safe workplace.

3. Always be properly grounded when touching a sensitive board, component, or assembly.

4. Store electrostatic-sensitive boards in protective packaging or on antistatic mats.

1.1.1. Grounding Methods

By adhering to the guidelines below, electrostatic damage to the device can be avoided:

1. Cover workstations with approved antistatic material. Always wear a wrist strap connected to workplace. Always

use properly grounded tools and equipment.

2. Use antistatic mats, heel straps, or air ionizers for more protection.

3. Always handle electrostatically sensitive components by their edge or by their casing.

4. Avoid contact with pins, leads, or circuitry.

5. Turn off power and input signals before inserting and removing connectors or connecting test equipment.

6. Keep work area free of non-conductive materials such as ordinary plastic assembly aids and Styrofoam.

7. Use only field service tools which are conductive, such as cutters, screwdrivers, and vacuum cleaners.

8. Always place drives and boards PCB-assembly-side down on the foam.

1.2. Lithium Battery Replacement

If replacing the lithium battery, follow the replacement precautions stated below.

Danger of explosion when replacing with wrong type of battery. Replace only with the
same or equivalent type recommended by the manufacturer. The lithium battery type
must be UL recognized.

Do not dispose of lithium batteries in general trash collection. Dispose of the battery
according to the local regulations dealing with the disposal of these special materials,
(e.g. to the collecting points for dispose of batteries).

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 16

2/ Electromagnetic Compatibility

For detailed information refer to section 10.3 “Standards and Certifications”.

2.1. Electromagnetic Compatibility (EU)

This product is intended only for use in industrial areas. The most recent version of the EMC guidelines (EMC Directive
2004/108/EC) apply. If the user modifies and/or adds to the equipment (e.g. installation of add-on cards) the
prerequisites for the CE conformity declaration (safety requirements) may no longer apply.

This is a class A product. In domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

2.2. FCC Statement (USA)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

2.3. EMC Compliance (Canada)

The method of compliance is self-declaration to Canadian standard ICES-003:

(English): This Class A digital apparatus complies with the Canadian ICES-003.

(French): Cet appareil numérique de la class A est conforme à la norme NMB-003 du Canada.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 17

3/ Shipment and Unpacking

Please check that your package is complete, and contains the items below (according to the ordered unit
configuration). If you discover damaged or missing items, please contact your dealer.

3.1. Unpacking

Proceed as follows to unpack the unit:

1. Remove packaging.

2. Do not discard the original packaging. Keep it for future relocation.

3. Check the delivery for completeness by comparing it with your order.

4. Please keep the associated paperwork. It contains important information for handling the unit.

5. Check the contents for visible shipping damage.

6. If you notice any shipping damage or inconsistencies between the contents and your order, please contact

Kontron for help and information.

3.2. Scope of Delivery

3.2.1. Standard

 1x KBox E-200 Series (corresponding to the ordered system configuration)
 1x Power adapter
 1x Power cord

3.2.2. Optional Parts

 Memory module
 Internal 2.5" SATA HDD / SSD
 mSATA card
 mPCIe card(s)
 Antenna(s)
 VESA mounting kit

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 18

4/ System Overview

The KBox E-200 Series is a fanless system enclosed within a robust compact aluminum chassis with cooling fins,
offering the superior qualities for operation in harsh environments.

It can be optionally factory-equipped with an mPCIe WLAN card and / or an mPCIe 3G / 4G card for three antennas.
Users may choose the implementation of a 2.5" SATA HDD / SSD and / or of an mSATA SSD card as storage media.

The following interfaces are available with the KBox E-200 Series:

Standard Front Panel:

 2x USB 3.0
 2x USB 2.0
 1x eSATA
 1x Line-Out
 1x Line-In
 1x Mic-In
 1x S/PDIF
 1x Power Button with LED
 1x Reset Button
 1x HDD LED
 1x Wireless LED

Standard Rear Panel:

 2x HDMI
 2x GbE LAN
 2x USB 3.0
 2x RS232/422/485
 1x 19 V DC Jack
 1x External Power Button
 2x Wi-Fi Antenna Port
 1x 3G / 4G Antenna Port

Standard Baseboard and System Expansion Capabilities:

 2x DDR3L SO-DIMM memory socket (DIMM1 & DIMM2 socket)
 1x SATA connector (SATA2 connector) for 2.5" SATA HDD / SSD
 1x full-sized mSATA socket (SATA1 socket) for mSATA SSD
 1x full-sized mPCIe socket (MPCIE2 socket) + 1x half-sized mPCIe socket (MPCIE1 socket)
 1x SIM card socket (SIM1 socket) only with the corresponding full-sized mPCIe card installed in the onboard

MPCIE2 socket

The device is designed to be operated in:

 Vertical position: mounted on the wall / the back of the monitor or inside a control cabinet / custom enclosure /

machine (with a vertical mounting kit) or

 Horizontal position: placed as a desktop unit (with the rubber feet).


When powering on the KBox E-200 Series, make sure that the cooling fins of the chassis are
not obstructed (covered) by any objects.

To provide sufficient heat dissipation by the cooling of the device, do not cover the cooling
fins of the KBox E-200 Series. Do not place any objects on the device. When installing the
system, please keep clearance for air circulation.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 19

4.1. System Expansion Capabilities

4.1.1. System Expansion via SATA Interface

The baseboard comes with an onboard SATA interface connector (Figure 4, pos. 2). Users can expand the KBox E-200
Series with a 2.5" SATA HDD / SSD drive.

4.1.2. System Expansion via mSATA Interface

The baseboard comes with an onboard full-sized mSATA interface connector (Figure 4, pos. 3). Users can expand the
KBox E-200Series with an mSATA SSD drive.

4.1.3. System Expansion via eSATA Interface

The front I/O panel comes with an mSATA interface connector (Figure 1, pos. ). Users can expand the KBox E-200
Series with an external SATA hard disk device.

4.1.4. System Expansion via mPCIe Card Interface

The baseboard comes with two onboard mPCIe interface connectors. One connector (Figure 4, pos. 4) is intended to
be used to install a half-sized mPCIe WLAN card and the other (Figure 4, pos. 5) is to install a full-sized mPCIe 3G / 4G
modem card.

4.1.4.1. System Expansion via SIM Socket

The baseboard comes with an onboard socket for a SIM card (Figure 4, pos. 6).

In order to use the SIM card reader functionality, a corresponding mPCIe modem card must be installed to the full­sized mPCIe socket (Figure 4, pos. 5) of your KBox E-200 Series.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 20

4.2. Front I/O Panel

Figure 1: Front I/O Panel

1 Power Button with LED (see Chapter 4.2.1)

2 HDD LED (see Chapter 4.2.2)

3 Wireless LED (see Chapter 4.2.3)

4 Reset Button (see Chapter 4.2.4)

5 Line-Out (see Chapter 4.2.5)

6 Mic-In (see Chapter 4.2.6)

7 Line-In (see Chapter 4.2.7)

8 S/PDIF (see Chapter 4.2.8)

9 USB 3.0 (see Chapter 4.2.9)

10 USB 2.0 (see Chapter 4.2.10)

11 eSATA (see Chapter 4.2.11)

4.2.1. Power Button with LDE

Press this button to turn the system on or off.

The power LED lights blue if the system is powered on (in an S0 state), blinks blue if the system in low-standby mode
(S1), blinks red if in high-standby mode (S3), and lights red if the system in hibernate mode (S4) or soft off state (S5).

Prerequisite: The system must be attached by means of the power cord to an appropriate mains (DC).

Even when the system is turned off via the power button there is still a standby voltage on
the baseboard. The unit is only completely disconnected from the DC mains, when the power
is removed.

4.2.2. HDD LED

The HDD LED blinks red when data is being written into or read from the HDD.

1

2

3

6

5 7

4 8

9

10

11 10

9

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 21

4.2.3. Wireless LED

The Wireless LED blinks green when data is transferring.

4.2.4. Reset Button

To clear the CMOS, use the tip of a pen or straightened-out paperclip to press the button briefly (for less than three
seconds).

4.2.5. Line-Out

The stereo headphone jack is used to connect the system’s audio out signal to amplified speakers or headphones.

4.2.6. Mic-In

The microphone jack is designed to connect the microphone used for video conferencing, voice narrations, or simple
audio recordings.

4.2.7. Line-In

The Line-in jack is designed to take input from a higher-powered sound source.

4.2.8. S/PFIF

The S/PDIF output connector is designed to carry digital audio signals out to external speakers or deliver compressed
AC3 signals to an external Dolby digital decoder.

4.2.9. USB 3.0

The front I/O panel of the KBox E-200 Series provides two USB 3.0 / 2.0 interface. This connector allows connection
of USB 3.0 or USB 2.0 compatible device to the system.

4.2.10. USB 2.0

The front I/O panel of the KBox E-200 Series provides two USB 2.0 / 1.1 interfaces. These connectors allow connection
of USB-compatible devices to the system.

4.2.11. eSATA

The KBox E-200 Series provides an eSATA connector on the front I/O panel. This connector allow connection of an
external SATA hard disk device to the system.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 22

4.3. Rear I/O Panel

Figure 2: Rear I/O Panel

1 DC Jack (see Chapter 4.3.1)

2 HDMI (see Chapter 4.3.2)

3 GbE (see Chapter 4.3.3)

4 USB 3.0 (see Chapter 4.3.4)

5 RS232/422/485 (see Chapter 4.3.5)

6 External Power Switch (see Chapter 4.3.6)

7 Wi-Fi Antenna (see Chapter 4.3.7)

8 3G / 4G Antenna (see Chapter 4.3.7)

4.3.1. DC Jack

The supplied power adapter converts AC power to DC for use with this jack. Power supplied through this jack supplies
power to the PC. To prevent damage to the PC, always use the supplied power adapter.

4.3.2. HDMI

The KBox E-200 Series provides two HDMI connectors. Two external (digital) displays can be connected to those
HDMI connectors.

4.3.3. GbE

These connectors are Gigabit Ethernet 10/100/1000 Mbit/s, IEEE 1588 capable interfaces. The connectors are
standard 8-pin RJ45 type connectors with status LEDs:

Figure 3: Ethernet LED Status

6

1

4

2 2

3

4

3 5 5

7 8

7

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 23

4.3.4. USB 3.0

The front I/O panel of the KBox E-200 Series provides two USB 3.0 / 2.0 interface. This connector allows connection
of USB 3.0 or USB 2.0 compatible device to the system.

4.3.5. RS232/422/485

COM 1 and COM 2 are provided as a 9-pin D-SUB connector and allow the connection of a serial peripheral. They are
designed to support RS232/422/485 serial communication which can be configured via BIOS setup.

4.3.6. External Power Switch

This connector allows integrators to locate an external power switch to power on and off the system.

4.3.7. Antenna

The KBox E-200 Series reserves three covered cutouts for the Reverse (RP) SMA connectors of two WLAN antennas
(mPCIe WLAN card with two antennas is an option) and one 3G / 4G antenna (mPCIe 3G / 4G modem card with one
antenna is an option).

LED satatus:

Orange - 1000 Mbit/s link established

Green - 100 Mbit/s link established

Off - 10 Mbit/s link established

LED satatus:

Off - Link is down

Flashing Green - Link is up and active

Steady Green - Link is up, no activity

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 24

4.4. Internal View

Figure 4: Internal view (without cover)

1 DDR3L SO-DIMM Memory Socket (DIMM1 & DIMM2, see Chapter 4.4.1)

2 SATA Connector (SATA2, see Chapter 4.4.2)

3 Full-sized mSATA Socket (SATA1, see Chapter 4.4.3)

4 Half-sized mPCIe Socket (MPCIE1, see Chapter 4.4.4)

5 Full-sized mPCIe Socket (MPCIE2, see Chapter 4.4.4)

6 SIM Card Socket (SIM1, see Chapter 4.4.4.1)

7 mSATA fixing bolt

8 Half-sized mPCIe fixing bolt

9 Full-sized mPCIe fixing bolt

10 Hard disk bracket fixing bolt

4.4.1. DDR3L SO-DIMM Memory Socket

The KBox E-200 Series provides two 204-pin DDR3L SO-DIMM socket to install memory RAM.

4.4.2. SATA Connector

The KBox E-200 Series provided one SATA 7+15 pin connector to install a 2.5" SATA HDD / SSD. An additional bracket is
required for holding and fixing the hard disk.

6 4

1 2 3 1

5

7

8 9 10

10

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 25

4.4.3. mSATA Socket

The KBox E-200 Series reserves one mSATA socket, allowing itself being extended with a full-sized mSATA SSD.

4.4.4. mPCIe Socket

The KBox E-200 Series reserves two mPCIe socket for expansion with a half-sized mPCIe WLAN card and a full-sized
mPCIe 3G / 4G modem card respectively.

4.4.4.1. System Expansion via SIM Socket

The baseboard of the KBox E-200 Series is equipped with a SIM card socket.

To avoid damage to the SIM card, insert the SIM card before you turn the power on and
remove the SIM card after you turn the power off.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 26

5/ Accessing Internal Components

This section contains important information that you must read before accessing the internal components. You must
follow these procedures properly when installing, removing or handling any board.

It is recommended to expand your system with additional mPCIe cards before it is installed into an equipment,
machine or cabinet. Please consider following instruction when you install (or remove) expansion cards.

Before installing/removing an add-on card, please pay attention to the following information:

Please observe the “General Safety Instructions for IT-Equipment” provided with the
system (refer to the chapter 1/) and the installation instructions in this manual.

Only personnel with appropriate qualifications, trainings and authorization are
permitted to install and work with the device.

The installation/removal of HHD / SSD and/or expansion cards may only be performed
by a qualified person, according to the description in this manual.

Before removing the cover of the device, make sure that the device is turned off and
disconnected from the power supply.

Before you upgrade the device with add-on cards, pay attention to the power
specifications in chapter 10/ “Technical Specifications” and make sure that the power
consumption of the add-on cards does not exceed 5 W per card.

Please

follow the safety instructions for components that are sensitive to electrostatic

discharge (ESD). Failure to observe this warning notice may result in damage to the
device or the latter’s components.

Please pay attention to the manufacturer’s instructions before installing/removing an
add-on card.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 27

5.1. Opening and Closing the KBox E-200 Series

Before opening the KBox E-200 Series, the system must be switched off and
disconnected from the main power supply. Also, disconnect all peripheral devices from
the KBox E-200 Series. Before you begin, ensure that you have a clean, flat and ESD­safe surface to work on.

For opening and closing the KBox E-200 Series, please perform the following steps:

1. Close all applications. Shut down the system properly and disconnect the connection to the main power source.

Disconnect all peripherals.

2. The KBox E-200 Series should lay on a flat, clean surface with the access cover facing upwards.

3. Loosen and remove the Phillips screws (two located on front I/O panel, five on the bottom and additional one on

the bottom (marked in blue in Figure 5) for fixing hard disk if installed), that secure the access cover to the

chassis. Retain the screws for later use.

Figure 5: Descrewing the access cover of the KBox E-200 Series

4. Slightly slide the access cover toward the front of the system and them lift it up.

5. Now you have access to the internal DDR3L SO-DIMM, SATA, mSATA, mPCIe and SIM sockets respectively in order

to remove or install hardware components.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 28

SIM card socket is located under 2.5" HDD / SSD. To remove or install it you have first to
lift up the HDD / SSD that is screwed to a bracket.

6. For closing replace carefully the access cover to the system and screw it on with the retained screws.

7. Tighten the retained screws when the cover is firmly in place.

When used as intended, the KBox E-200 Series is to operate only in closed condition.
Only when the access cover is properly fixed with the screws and the rear side with

WLAN antennas are properly installed and secured with the screws, it is ensured that
the user does not have access to the internal parts of the KBox E-200 Series.

5.1.1. Installing an HDD / SSD

To install an 2.5" HDD / SSD please proceed according to the steps described:

1. Open the device as described in the subsection 5.1 "Opening and Closing the KBox E-200 Series" (step 1-5).

2. Screw the bracket to the HDD / SSD.

3. Locate the SATA socket (SATA2) (Figure 4, pos. 2) and the corresponding fixing bolts (Figure 4, pos. 10).

4. Align the notches on the HDD / SSD with the notches in the SATA socket (SATA2). Insert the HDD / SSD into the

corresponding docket (Figure 4, pos. 2) and rotate it down with the fixing hole of the bracket cover the fixing

bolts.

5. Press the HDD / SSD and its bracket down on the side with the fixing holes and secure it with the available

fastening screws (Figure 4, pos. 10).

Figure 6: Installing an HDD/ SSD

1 SATA Connector

2

1

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 29

2 Hard Disk Bracket

6. In order to close the KBox E-200 Series, proceed step 6 & 7 described in the subsection 5.1 "Opening and Closing

the KBox E-200 Series".

5.1.2. Installing an mSATA SSD

To have access the mSATA socket please proceed according to the steps described:

1. Open the device as described in the subsection 5.1 "Opening and Closing the KBox E-200 Series" (step 1-5).

2. Locate the mSATA socket (SATA1) (Figure 4, pos. 3) and the corresponding fixing bolt. (Figure 4, pos. 7).

3. Align the notches on the mSATA SSD with the notches in the mSATA socket (SATA1). Insert the mSATA SSD into

the corresponding socket (Figure 4, pos. 3) and rotate it down with the fixing hole of the card over the fixing bolt.

4. Press the mSATA SSD down on the side with the fixing hole and secure it with the available fastening screw

(Figure 4, pos. 7).

5. In order to close the KBox E-200 Series, proceed step 6 & 7 described in the subsection 5.1 "Opening and Closing

the KBox E-200 Series".

5.1.3. Installing an mPCIe expansion card

To have access the mPCIe socket please proceed according to the steps described:

1. Open the device as described in the subsection 5.1 "Opening and Closing the KBox E-200 Series" (step 1-5).

2. Locate the mPCIe socket (MPCIE1 or MPCIE2) (Figure 4, pos. 4 or 5) and the corresponding fixing bolt. (Figure 4,

pos. 8 or 9).

3. Align the notches on the mPCIe expansion card with the notches in the mPCIe socke (MPCIE1 or 2). Insert the

mPCIe expansion card into the corresponding socket (Figure 4, pos. 8 or 9) and rotate it down with the fixing hole

of the card over the fixing bolt.

4. Press the mPCIe expansion card down on the side with the fixing hole and secure it with the available fastening

screw (Figure 4, pos. 8 or 9).

5. In order to close the KBox E-200 Series, proceed step 6 & 7 described in the subsection 5.1 "Opening and Closing

the KBox E-200 Series".

5.1.4. Installing the SIM card

To have access the SIM card socket please proceed according to the steps described:

1. Open the device as described in the subsection 5.1 "Opening and Closing the KBox E-200 Series" (step 1-5).

2. Locate the SIM card socket (SIM1) (Figure 4, pos. 7).

3. To unlock the SIM card socket slide the cover of the SIM socket in the direction shown in Figure 7.

4. Lift gently the slot cover and open the slot cover as shown in Figure 7.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 30

5. Slide the SIM card into the left and right card guides of the socket cover and push down the cover in order to

close the cover as shown in Figure 7.

6. After closing the cover, lock the cover by sliding the closed cover in the direction shown in Figure 7.

Figure 7: Installing the SIM card

7. In order to close the KBox E-200 Series, proceed step 6 & 7 described in the subsection 5.1 "Opening and Closing

the KBox E-200 Series".

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 31

6/ Thermal Considerations

6.1. Available Processors

Please refer to the chapter 10/ "Technical Specifications".

The list of processors may be extended over the product lifetime.

6.2. Convection Cooling

The applied cooling method provides adequate cooling of the device during operation and performs a one-way
thermal transfer to the chassis. Three sides of the KBox E-200 Series consist of a compact aluminum U-shaped
chassis are with cooling fins. The cooling fins provide heat dissipation during operation.

To provide sufficient heat dissipation for the cooling of the KBox E-200 Series, never
cover the cooling fins of the chassis. Do not place any objects on the device.

6.3. System Clearance

To provide a maximum of airflow through and around the box, proper distances to surrounding parts must be
observed.

6.4. Maximum Temperatures

The maximum system ambient temperature depends mostly on the power consumption
of the processor and the chipset.

For the temperature evaluation a specialised tool from Intel® was used to set the processor to a defined workload.
Depending on the power consumption one or more cores were set to 75% workload. This includes the graphics core.
The tool also handles the usage of the "Turbo Mode" of certain processor types.

The processor utilization depends highly on the software used. Software using
multicore feature will run on several cores whereas standard software will only utilize
one core. In this case the processor will use the "Turbo Mode" to increase the clock for
the core with the highest workload, as long as the temperature is within limits.

6.5. Third Party Components

When the KBox E-200 Series is extended and configured with third party components like mPCIe expansion card and
hard drives (HDD or SSD), it has to be taken into account that the air temperature inside the system is higher than the
ambient temperature. An approximately internal temperature rise is given for assistance.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 32

7/ Installation Instructions

The KBox E-200 Series system is designed for operating:

 within a control cabinet/ custom enclosure / machine or onto a wall / the back of a monitor by use of a VESA

mounting kit

 as desktop unit by attaching the self-adhesive feet.

Expansion card installation should be performed before installing the KBox E-200
Series into control cabinet / custom enclosure / machine, or onto wall / monitor.



Whenever possible, unpack or pack this product only at EOS/ESD safe work stations.
Where a safe work station is not guaranteed, it is important for the user to be
electrically discharged before touching the product with his/her hands or tools. This is
most easily done by touching a metal part of the system chassis.

Do not handle this product out of its protective enclosure while it is not used for
operational purposes unless it is otherwise protected.

Prior any installation work, ensure that there are no live wires on the installation site.
Do not handle the device if there is any damage visible.
Do not operate the KBox E-200 Series with foreign objects inside the chassis.
Further do not insert any retrieval device into the device while it is connected to power.

Kontron rejects all liability for any and all damages resulting from operation of the unit

with foreign objects inside the chassis.
The KBox E-200 Series has to be installed and operated only by trained and qualified

personnel.
Only personnel with appropriate qualifications, trainings and authorization are

permitted to install and work with the Kontron KBox E-200 Series.
This device shall only be installed in or connected to systems that fulfill all necessary

technical and specific environmental requirements.
The unit must be placed such that there is sufficient space in front and rear of it for

connecting the cables to the I/O interface connectors and for operating the power
button.

Leave sufficient free space around the unit to prevent the device from possibly
overheating!

The KBox E-200 Series must be firmly attached to a clean flat and solid mounting
surface. Use proper fastening materials suitable for the mounting surface. Ensure that
the mounting surface type and the used mounting solution safely support the load of
the KBox E-200 Series and the attached components.

Please follow the local/national regulations for grounding.
The voltage feeds must not be overloaded. Adjust the cabling and the overcurrent

protection to correspond with the electrical figures indicated on the type label.
The type label is located next to the access cover of the system.
It is recommended that the last cable attached to the system should be the power

cable! Refer to the section 7.2 “DC Power Connection” and chapter 8/ “Starting Up”.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 33

7.1. System Mounting

In order to adapt the KBox E-200 Series for mounting Kontron offers different mounting solution such as:

 KBox E-200 Series configuration with a VESA mounting kit for vertical installation into a control cabinet / custom

enclosure / machine or onto a wall / the back of a monitor

 KBox E-200 Series as desktop unit with 4 rubber feet

Depending on the ordered KBox E-200 Series configuration, your system may be supplied with a VESA mounting kit
(Figure 8). The kit consists of two parts: a base bracket (Figure 8, pos. 1) to be fixed permanently on the mounting
surface and another hooked bracket to hold the KBox E-200 Series with a hand-screw knob (Figure 8, pos. 2) to
secure two brackets.

Figure 8: Optional VESA mounting kit for KBox E-200 Series

1 Base mounting bracket

2 Hooked mounting bracket with a hand-screw knob

The base mounting bracket complies with VESA 75 and VESA 100 patterns (Figure 9). To fasten the bracket, the
control cabinet / custom enclosure / machine / monitor / wall must have VESA 75, VESA 100 or other screw pattern
shown as Figure 9 for mounting.

Figure 9: Hole pattern of base mounting bracket for KBox E-200 Series

2

1

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 34

To mount the KBox E-200 Series please proceed according to the steps described:

1. Prepare the mounting surface with sufficient screws (four screws for VESA mount) and if necessary anchors

corresponding to the mounting surface type if no VESA-compliant screw holes are available.

2. Secure the base mounting bracket to the mounting surface with screws (Figure 10). The following figures take

VESA mounting to a monitor as an example.

Figure 10: Securing the base mounting bracket

3. Secure the hooked mounting bracket onto the bottom side of the KBox E-200 (Figure 11). The front I/O panel

should be placed upward.

Figure 11: Securing the hooked mounting bracket onto the KBox E-200 Series

4. Place the KBox E-200 Series onto the mounting surface by sliding the hooked mounting bracket into the based

mounting bracket (Figure 12).

5. Secure the hand-screw knob located on the hooked mounting bracket to fix two brackets (Figure 12).

Figure 12: Securing the KBox E-200 Series onto the mounting surface

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 35

For a sufficient air circulation around the device, we recommend keep a proper
clearance and not mount / operate any other devices within the clearance around the
KBox E-200 Series.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 36

7.2. DC Power Connection

The KBox E-200 Series is connected by a DC power input jack (Figure 2, pos. 1) to a DC power source.

The KBox E-200 Series is delivered with a power adapter to convert AC voltage into DC 19V and a power cord to carry
AC power to the power adapter.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 37

8/ Starting Up

The KBox E-200 Series must be only operated with the nominal voltage of 19V DC of
type SELV. For details refer to the chapter 10/ “Technical Specifications”.

8.1. Connecting to DC Power Supply

The DC power input jack (Figure 2, pos. 1) is located on the rear side of the KBox E-200 Series. The KBox E-200 Series
will be connected to a AC-to-DC power adapter via the supplied male DC power plug and corresponding power cable
attached to the adapter.

Before using your system, become familiar with the system components and check that

everything is connected properly. Following a proper cabling procedure will prevent a
false power-on condition, which could result in unit operational failure.

When you install/disconnect the unit, the functional earth connection must always be
made first and disconnected last.

Also, it is recommended that the last connections attached to the system should be the
power wires!

The KBox E-200 Series must be connected DC power supply complying with the SELV
(Safety Extra Low Voltage) requirements of EN 60950-1 standard. It must be observed
that wiring and short-circuit/overcurrent protection is performed according to the
applicable standards, regulations and respect to the electrical specification of the
KBox E-200 Series.

Even when the system is turned off via the power button (Figure 1, pos. 1) parts of the
system are still energized.

The disconnecting device (fuse/circuit backer) rating must be in accordance with the
wire cross-section and the rated current of the KBox E-200 Series.

The cables must have some form of support so as to minimize the strain on the unit’s
connectors.

To connect the KBox E-200 Series to a corresponding DC power supply, please perform the following steps:

1. Connect the power adapter cable to the DC jack (DC IN, Figure 2, pos. 1) of the KBox E-200 Series.

2. Connect the power cable to the power adapter.

3. Connect the power cable to a power outlet.

4. Press the power button (Figure 1, pos. 1) on the front panel to turn on the system.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 38

8.2. Operating System and Hardware Component Drivers

Your system can be supplied optionally with a pre-installed operating system.

If you have ordered your KBox E-200 Series with a pre-installed operating system, all drivers are installed in
accordance with the system configuration ordered (optional hardware components). Your system is fully operational
when you switch it on for the first time. Please pay attention to the following note.

Important information on the use of the pre-installed “WINDOWS 7 ULTIMATE FOR
EMBEDDED SYSTEMS” or “WINDOWS 7 PROFESSIONAL FOR EMBEDDED
SYSTEMS“ operating systems:

The terms and conditions for the use of the pre-installed operating systems are
specified in the document “MICROSOFT SOFTWARE LICENSE TERMS”.

You can download this document from our web site www.kontron.com by selecting
Product/ Downloads tab/Windows.

If you have ordered The KBoxE-200 Series without a pre-installed operating system, you will need to install the
operating system and the appropriate drivers for the system configuration you have ordered (optional hardware
components) yourself.

You can download the relevant drivers for the installed hardware from our web site at
www.kontron.com by selecting the product.

Pay attention to the manufacturer specifications of the operating system and the
integrated hardware components.

Latest Linux Distribution and Kernel shall be used in order to properly support the
Haswell / Broadwell graphics engine.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 39

9/ Maintenance and Cleaning

Equipment from Kontron requires only minimum servicing and maintenance for proper operation.

 For light soiling, clean the KBox E-200 Series with a dry cloth. Carefully remove dust from the surface of the

cooling fins of the chassis using a clean, soft brush.

 Stubborn dirt should be removed using a mild detergent and a soft cloth.

Do not use steel wool, metallic threads or solvents like abrasives, alcohol, acetone or
benzene for cleaning the KBox E-200 Series.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 40

10/ Technical Specifications

Table 1: Technical Specifications

System

Processor Intel® Haswell / Broadwell U-Series Processors (Dual Core, FCBGA1168, 15 W TDP)

Memory 2x DDR3L 1333 / 1600 SO-DIMM memory socket

Video

Display Interface 2x HDMI (on rear, 3840 x 2160 @ 60 Hz)

Multiple Display Dual

Audio

Audio Codec Realtek ALC662-VD

Audio Interface

 1x Line-in (on front)
 1x Line-out (on front)
 1x Mic-in (on front)
 1x S/PDIF (on front)

Network Connection

Ethernet 2x GbE LAN (RJ45 on rear, 1x Intel® I217-LM, 1x Realtek RTL8111G-CG)

Peripheral Connection

USB

 4x USB 3.0 (2x Type A on front, 2x Type A on rear)
 2x USB 2.0 (Type A on rear)

Serial Port 2x RS232/422/485 (DB9 on rear)

Storage & Expansion

Storage &
Expansion

 1x 2.5" SATA HDD / SSD
 1x eSATA (with power supply, on front)
 1x mSATA (full size)
 2x mPCIe (1x half size, 1x full size)
 1x SIM Card Cage (on board)

Power

Input Voltage DC 19 V

Connector Lockable DC Jack (on rear)

Power Adapter AC to DC, 100 V ~ 240 V

Firmware

BIOS AMI uEFI BIOS w/ 128 Mb SPI Flash

Watchdog Programmable WDT to generate system reset event

H/W Monitor Voltages, Temperatures

Real Time Clock Processor integrated RTC

TPM Supported for model w/ Core™ i5 / i7 CPU (Infineon SLB 9635 TPM 1.2)

iAMT Supported for model w/ Core™ i5 / i7 CPU

System Control & Monitoring

Button, Switch &
Indicator

 1x Power Button with LED (on front)
 1x Reset Button (on front)
 1x Wireless LED (on front)

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 41

 1x HDD LED (on front)
 1x External Power Button (on rear)

Cooling

Cooling Method Passive

Software

OS Support Windows 7, Windows 8, Linux

10.1. Mechanical Specifications

Table 2: Mechanical Specifications

Construction Aluminum Chassis

Dimensions (W x D x H) 220 mm x 153.3 mm x 38 mm / 8.66" x 6.04" x 1.50"

Weight 1600 g / 3.53 lb

Mounting VESA Mount

10.1.1. Mechanical Drawing

Figure 13: Mechanical Drawing

(unit: mm)

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 42

10.2. Environmental Conditions

Table 3: Environmental Conditions

Operating Temperature 0 °C ~ 50 °C / 32 °F ~ 122 °F

Storage Temperature -20 °C ~ 80 °C / -4 °F ~ 176 °F

Humidity 0 % ~ 90 %

10.3. Standards and Certifications

Table 4: Standards and Certifications

CE

 EN 55022: 2010 + AC: 2011 Class A
 EN 55024: 2010
 EN 61000-3-2: 2006 + A1: 2009 + A2: 2009 Class D
 EN 61000-3-3: 2013
 IEC 60950-1: 2005 (Second Edition) + Am 1: 2009 + Am 2: 2013
 EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013

FCC

 FCC CFR Title 47 Part 15 Subpart B: 2012
 ANSI C63.4-2009
 ICES-003 Issue 5: 2012
 CISPR 22: 2008
 CAN/CSA-CISPR 22-10

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 43

11/ Standard Interfaces – Pin Assignments

Low-active signals are indicated by a minus sign.

11.1.1. DC Jack

Table 5: DC Jack (see Figure 2, pos.1)

Pin Signal Name DC Jack (female)

1 +19Vin

2 GND

11.1.2. Ethernet Connectors

Table 6: Ethernet Connector (see Figure 2, pos. 3)

Pin Signal Name LAN1, LAN2 (RJ45)

1 TX1+

8 7 6 5 4 3 2 1

2 TX1-

3 TX2+

4 TX3+

5 TX3-

6 TX2-

7 TX4+

8 TX4-

11.1.3. USB 3.0 Port

Table 7: USB 3.0 Port (see Figure 1, pos. 9 & Figure 2, pos.4)

USB 2.0 Contact Pins USB 3.0 Contact Pins 9-pin USB Connector Type A Version 3.0 / 2.0

Pin Signal Name Pin Signal Name

1 +USBVCC 5 USB_RX-

2 USB_D- 6 USB_RX+

3 USB_D+ 7 GND

4 GND 8 USB_TX-

9 USB_TX+

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 44

11.1.4. USB 2.0 Port

Table 8: USB 2.0 Port (see Figure 1, pos. 10)

Pin Signal Name 4-pin USB Connector Type A Version 2.0

1 +USBVCC

2 USB_D-

3 USB_D+

4 GND

11.1.5. HDMI Connector

Table 9: HDMI Connector (see Figure 2, pos. 2)

Pin Signal Name HDMI Connector Type A Version 1.4

1 TMDS Data2+

2 Ground

3 TMDS Data2–

4 TMDS Data1+

5 Ground

6 TMDS Data1–

7 TMDS Data0+

8 Ground

9 TMDS Data0–

10 TMDS Clock+

11 Ground

12 TMDS Clock–

13 Reserved

14 Reserved

15 DDC_CLK

16 DDC_DATA

17 Ground

18 +5 V Power

19 Hot Plug Detect

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 45

11.1.6. RS232/422/485 Serial Port

Table 10: RS232/422/485 Serial Port (see Figure 2, pos. 5)

Pin RS232 RS422 RS485

Half
Duplex

RS485
Full
Duplex

COM1, COM2 (9-pin D-SUB Male Connector)

1 DCD TX- DATA- TX-

2 RXD TX+ DATA+ TX+

3 TXD RX+ N/A RX+

4 DTR RX- N/A RX-

5 GND GND GND GND

6 DSR N/A N/A N/A

7 RTS N/A N/A N/A

8 CTS N/A N/A N/A

9 RI / +5V* NA/+5V* NA/+5V* NA/+5V*

* Pin-9 can be set for +5V output in BIOS setup.

11.1.7. Line-Out Connector

Table 11: Line-Out Connector (see Figure 2, pos. 5)

Pin Signal Name Line-Out Connector & Corresponding Audio Jack

Tip Line-Out_L

Ring Line-Out_R

Sleeve GND

11.1.8. Mic-In Connector

Table 12: Mic-In Connector (see Figure 2, pos. 6)

Pin Signal Name Mic-In Connector & Corresponding Audio Jack

Tip Mic-In_L

Ring Mic-In_R

Sleeve GND

11.1.9. Line-In Connector

Table 13: Line-In Connector (see Figure 2, pos. 7)

Pin Signal Name Line-In Connector & Corresponding Audio Jack

Tip Line-In_L

Ring Line-In_R

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 46

Pin Signal Name Line-In Connector & Corresponding Audio Jack

Sleeve GND

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 47

11.1.10. eSATA Connector

Table 14: eSATA Connector (see Figure 1, pos. 11)

Pin Signal Name 11-pin eSATA Connector

S1 GND

S2 TX+

S3 TX-

S4 GND

S5 RX-

S6 RX+

S7 GND

U1 +5V

U2 NC

U3 NC

U4 GND

11.1.11. External Power Switch Wafer

Table 15: External Power Switch Wafer (see Figure 2, pos.6)

Pin Signal Name 2-pin Power Switch Wafer

1 Power S/W+

2 Power S/W-

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 48

12/ uEFI BIOS

12.1. Starting the uEFI BIOS

The KBox E-200 Series is provided with a Kontron-customized, pre-installed and configured version of AMI Aptio® V
uEFI BIOS. AMI BIOS firmware is based on the Unified Extensible Firmware Interface (uEFI) specification and the Intel®
Platform Innovation Framework for EFI. This uEFI BIOS provides a variety of new and enhanced functions specifically
tailored to the hardware features of the KBox E-200 Series.

The BIOS version covered in this document might not be the latest version. The latest
version might have certain differences to the BIOS options and features described in
this chapter.

The uEFI BIOS comes with a setup program that provides quick and easy access to the individual function settings for
control or modification of the uEFI BIOS configuration. The setup program allows the accessing of various menus that
provide functions or access to sub-menus with more specific functions of their own.

To start the uEFI BIOS setup program, follow the steps below:

1. Power on the board.

2. Wait until the first characters appear on the screen (POST messages or splash screen).

3. Press the <DEL> key.

4. If the uEFI BIOS is password-protected, a request for password will appear. Enter either the User Password or the

Supervisor Password (see Security menu), press <RETURN>, and proceed with step 5.

5. A setup menu will appear.
The KBox E-200 Series uEFI BIOS setup program uses a hot key-based navigation system. A hot key legend bar is
located on the bottom of the setup screens.

The following table provides information concerning the usage of these hot keys.

Table 16: Navigation Hot Keys Available in the Legend Bar

Hotkeys Description

<F1> The <F1> key invokes the General Help window.

<-> The <Minus> key selects the next lower value within a field.

<+> The <Plus> key selects the next higher value within a field.

<F2> The <F2> key loads the previous values.

<F3> The <F3> key loads the standard default values.

<F4> The <F4> key saves the current settings and exit the uEFI BIOS setup.

<→> or <←>

The <Left/Right> arrows selects major setup menus on the menu bar. For example:
Main, Advanced, Security, etc.

<↑> or <↓>

The <Up/Down> arrows selects fields in the current menu. For example: A setup
function or a sub-screen.

<ESC> The <ESC> key exits a major setup menu and enter the Exit setup menu.

Pressing the <ESC> key in a sub-menu displays the next higher menu level.

<RERURN> The <RETURN> key executes a command or select a submenu.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 49

12.2. Setup Menus

The Setup utility features shows six menus in the selection bar at the top of the screen:

 Main
 Advanced
 Power
 Boot
 Security
 Save & Exit

The Setup menus are selected via the left and right arrow keys. The currently active menu and the currently active
uEFI BIOS Setup item are highlighted in white. Each Setup menu provides two main frames. The left frame displays all
available functions. Functions that can be configured are displayed in blue. Functions displayed in gray provide
information about the status or the operational configuration. The right frame displays an Item Specific Help window
providing an explanation of the respective function.

12.2.1. Main Setup Menu

Upon entering the uEFI BIOS Setup program, the Main Setup menu is displayed. This screen lists the Main Setup menu
sub-screens and provides basic system information. Additionally functions for setting the system time and date are
offered.

Table 17: Main Setup Menu Sub-Screens and Functions

Function Description

BIOS Information Read only field.

Displays information about the system BIOS

Memory Information Read only field.

Displays information about total memory

ME Information Read only field.

Displays information about Intel Management Engine (ME) version

Firmware Information Code version and firmware information

System Date Set System Date

System Time Set System Time

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 50

Figure 14: BIOS Main Menu Screen System Data and Time

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Product Information

Product Name KBox E-200

BIOS Version R1.00 (x64)

BIOS Build Date 09/05/2014

ME FW Version 9.5.20.1742

CPU Information

Intel® Core™ i5-4300U CPU @ 2.90GHz

Microcode Revision 17

Processor Cores 2

→ ←: Select Screen

Memory Information

↑ ↓: Select Item

Total Size 2048 MB (DDR3) Enter: Select

Frequency 1333 MHz +/-: Change Opt.

F1: General Help

System Date [Wed 04/02/2014] F2: Previous Values

System Time [13:22:19] F3: Optimized Defaults

F4: Save & Exit

Access Level Administrator ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

System Date [dd/mm/yyyy] Set the Date. Use Tab to switch between Data elements.

System Time [hh:mm:ss] Set the Time. Use Tab to switch between Time elements.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 51

12.2.2. Advanced Setup Menu

The Advanced setup menu provides sub-screens and functions for advanced configurations. The following sub­screen functions are included in the menu:

 LAN & Audio Configuration
 Display Configuration
 Super IO Configuration
 CPU Advanced Configuration
 SATA Configuration
 USB Configuration
 Intel® Rapid Start Technology
 H/W Monitor

Setting items on this screen to incorrect values may cause the system to malfunction.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 52

Figure 15: BIOS Advanced Menu

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Onboard LAN1 Controller [Enabled]

Onboard LAN1 Boot [Disabled]

Onboard LAN2 Controller [Enabled]

Onboard LAN2 Boot [Disabled]

Audio Controller [Enabled]

→ ←: Select Screen

↑ ↓: Select Item

> Display Configuration Enter: Select

> Super IO Configuration +/-: Change Opt.

> CPU Chipset Configuration F1: General Help

> SATA Configuration F2: Previous Values

> USB Configuration F3: Optimized Defaults

> Intel® Rapid Start Technology F4: Save & Exit

> H/W Monitor ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

Onboard LAN1
Controller

[Disabled], [Enabled] Select whether to enable or disable Onboard LAN1 Controller.

Onboard LAN1 Boot [Disabled], [Enabled] Select whether to enable or disable load onboard PXE (Preboot

Execution Environment).

Onboard LAN2
Controller

[Disabled], [Enabled] Select whether to enable or disable Onboard LAN2 Controller.

Onboard LAN2 Boot [Disabled], [Enabled] Select whether to enable or disable load onboard PXE (Preboot

Execution Environment).

Audio Controller [Disabled], [Enabled] Select whether to enable or disable Audio Controller.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 53

Figure 16: BIOS Advanced Menu - Display Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Display Configuration

UWA Frame Buffer Size [256MB]

→ ←: Select Screen

DVMT Pre-Allocated [64M]

↑ ↓: Select Item

DVMT Total Gfx Mem [256M] Enter: Select

+/-: Change Opt.

Primary IGFX Boot Display [VBIOS Default] F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

UWA Frame Buffer
Size

[128MB], [256MB],
[512MB]

Select the Aperture Size.

DVMT Pre-Allocated [32M], [64M], [96M],

[128M], [160M],
[192M], [224M],
[256M], [288M],
[320M], [352M],
[384M], [416M],
[448M], [480M],
[512M], [1024M]

Select DVMT Pre-Allocated (Fixed) Graphics Memory size used
by the Internal Graphics Device.

DVMT Total Gfx Mem [128M], [256M], [MAX] Select DVMT Total Graphic Memory size used by the Internal

Graphics Device.

Primary IGFX Boot
Display

[VBIOS Default],
[HDMI 1], [HDMI 2]

Select the Video Device which will be activated during POST. This
has no effect if external graphics present.

Secondary boot display selection will appear based on your
selection.

DOS modes will be supported only on primary display.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 54

Figure 17: BIOS Advanced Menu - Super IO Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Super IO Configuration

> Serial Port 1 Configuration

→ ←: Select Screen

> Serial Port 2 Configuration

↑ ↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Figure 18: BIOS Advanced Menu - Super IO Configuration - Serial Port 1 Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Serial Port 1 Configuration

Serial Port [Enabled]

→ ←: Select Screen

Device Settings IO=3F8h; IRQ=4;

↑ ↓: Select Item

Enter: Select

Change Setting [Auto] +/-: Change Opt.

Serial Port 1 Type [RS232] F1: General Help

RS485 Deplux Mode* [Half Duplex] F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

* These items appear only when selecting RS485 for the Serial Port 1 Type.

Feature Option Description

Serial Port [Disabled], [Enabled] Select whether to enable or disable Serial Port (COM).

Change Settings [Auto], [IO=3F8h;

IRQ=4;], [IO=3F8h;
IRQ=3, 4, 5, 6, 7, 10, 11,
12;], [IO=2F8h; IRQ=3,
4, 5, 6, 7, 10, 11, 12;],
[IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12;],
[IO=2E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12;]

Select an optional setting for Super IO device.

Serial Port 1 Type [RS232], [RS422], Select an appropriate type for Serial Port 1.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 55

Feature Option Description

[RS485]

RS485 Duplex Mode [Half Duplex], [Full

Duplex]

Select an appropriate RS485 Duplex Mode.

Figure 19: BIOS Advanced Menu - Super IO Configuration - Serial Port 2 Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Serial Port 2 Configuration

Serial Port [Enabled]

→ ←: Select Screen

Device Settings IO=2F8h; IRQ=3;

↑ ↓: Select Item

Enter: Select

Change Setting [Auto] +/-: Change Opt.

Serial Port 2 Type [RS232] F1: General Help

RS485 Deplux Mode* [Half Duplex] F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

* These items appear only when selecting RS485 for the Serial Port 2 Type.

Feature Option Description

Serial Port [Disabled], [Enabled] Select whether to enable or disable Serial Port (COM).

Change Settings [Auto], [IO=2F8h;

IRQ=3;], [IO=3F8h;
IRQ=3, 4, 5, 6, 7, 10, 11,
12;], [IO=2F8h; IRQ=3,
4, 5, 6, 7, 10, 11, 12;],
[IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12;],
[IO=2E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12;]

Select an optional setting for Super IO device.

Serial Port 2 Type [RS232], [RS422],

[RS485]

Select an appropriate type for Serial Port 2.

RS485 Duplex Mode [Half Duplex], [Full

Duplex]

Select an appropriate RS485 Duplex Mode.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 56

Figure 20: BIOS Advanced Menu - CPU Advanced Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

CPU Advanced Configuration

EIST [Enabled]

→ ←: Select Screen

Hyper Threading [Enabled]

↑ ↓: Select Item

VT-d [Enabled] Enter: Select

Active Processor Cores [All] +/-: Change Opt.

Limit CPUID Maximum [Disabled] F1: General Help

Execute Disable Bit [Enabled] F2: Previous Values

Intel Virtualization Technology [Disabled] F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

EIST [Disabled], [Enabled] Select whether to enable or disable Enhanced Intel SpeedStep

Technology.

Hyper Threading [Disabled], [Enabled] Select whether to enable or disable Hyper-threading

technology.
[Enabled] for Windows XP and Linux (OS optimized for Hyper-

Threading Technology).
[Disabled] for other OS (OS not optimized for Hyper-Threading

Technology).

VT-d [Disabled], [Enabled] Select whether to enable or disable VT-d capability.

Active Processor
Cores

[All], [1] Select the number of cores to enable in each processor package.

Limit CPUID Maximum [Disabled], [Enabled] Select whether to limit CPUID maximum value.

Execute Disable Bit [Disabled], [Enabled] Select whether to enable or disable Execute Disable Bit

functionality, which prevents malicious buffer overflow attacks..

Intel Virtualization
Technology

[Disabled], [Enabled] Select whether to enable or disable Intel Virtualization

Technology.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 57

Figure 21: BIOS Advanced Menu - SATA Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

SATA Controller(s) [Enabled]

SATA Mode Selection [AHCI]

→ ←: Select Screen

SATA Controller Speed [Default]

↑ ↓: Select Item

Enter: Select

Serial ATA Port 1 Empty +/-: Change Opt.

Port 1 [Enabled] F1: General Help

mS ATA Port 1 Empty F2: Previous Values

Port 1 [Enabled] F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

SATA Controller(s) [Enabled], [Disabled] Select whether to enable or disable SATA Device.

SATA Mode Selection [AHCI] Determine how SATA controller(s) operate.

SATA Controller
Speed

[Default], [Gen 1],
[Gen 2], [Gen 3]

Indicate the maximum speed the SATA controller can support.

Port 1 [Disabled], [Enabled] Select whether to enable or disable SATA Port 1 or mSATA Port 1.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 58

Figure 22: BIOS Advanced Menu - USB Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

USB Configuration

USB Devices:

→ ←: Select Screen

1 Keyboard, 1 Hubs

↑ ↓: Select Item

Enter: Select

Legacy USB Support [Enabled] +/-: Change Opt.

USB 3.0 Support [Enabled] F1: General Help

XHCI Hand-off [Enabled] F2: Previous Values

EHCI Hand-off [Disabled] F3: Optimized Defaults

USB Mass Storage Driver Support [Enabled] F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

Legacy USB Support [Enabled], [Disabled],

[Auto]

Select whether to enable or disable Legacy USB support.
AUTO option disables legacy support if no USB devices are

connected.

USB 3.0 Support [Disabled], [Enabled] Select whether to enable or disable USB 3.0 support.

XHCI Hand-off [Enabled], [Disabled] Select whether to enable or disable XHCI Hand-off function.

This is a workaround for OSes without XHCI hand-off support.
The XHCI ownership change should be claimed by XHCI driver.

EHCI Hand-off [Disabled], [Enabled] Select whether to enable or disable EHCI Hand-off function.

USB Mass Storage
Driver Support

[Disabled], [Enabled] Select whether to enable or disable USB Mass Storage Driver

Support.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 59

Figure 23: BIOS Advanced Menu - Intel® Rapid Start Technology

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Intel® Rapid Start Technology [Disabled]

→ ←: Select Screen

↑ ↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

Intel® Rapid Start
Technology

[Enabled], [Disabled] Select whether to enable or disable Intel® Rapid Start

Technology.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 60

Figure 24: BIOS Advanced Menu - H/W Monitor

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

PC Health Status

CPU Temperature : +37 C

→ ←: Select Screen

Memory Temperature : +38 C

↑ ↓: Select Item

System Temperature : +31 C Enter: Select

+/-: Change Opt.

+VCORE : +1.720 V F1: General Help

+VIN : +19.104 V F2: Previous Values

+5V : +5.089 V F3: Optimized Defaults

+3.3V : +3.356 V F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 61

12.2.3. Power Setup Menu

The Power setup menu provides functions and a sub-screen for power configurations. The following sub-screen
function is included in the menu:

 WatchDog Timer Configuration

Figure 25: BIOS Power Setup Menu

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Power Management Configuration

ACPI Sleep State [S3 only (Suspend to RAM)]

Restore AC Power Loss [Power Off]

→ ←: Select Screen

Power Saving Mode [Disabled]

↑ ↓: Select Item

Enter: Select

Resume Event Control +/-: Change Opt.

Resume By PCIE Device [Disabled] F1: General Help

Resume By RTC Alarm [Disabled] F2: Previous Values

EUP Power Saving Mode [Disabled] F3: Optimized Defaults

> WatchDog Timer Configuration F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

ACPI Sleep State [Suspend Disabled],

[S1 only (CPU Stop
Clock)], [S3 only
(Suspend to RAM)]

Select whether to enable or disable suspend function and
determine an appropriate suspend mode.

Restore AC Power
Loss

[Power Off], [Power
On], [Last State]

Control whether the system will stay on after AC power is
removed and then restored.

Select [Power Off] if you want the system to remain off after
power restored.

Select [Power On] if you use a power strip to turn the system on.

Power Saving Mode [Disabled], [EUP

Enabled], [DeepSx
Enabled]

Select whether to enable Power Saving Mode.

Resume By PCIE
Device

[Disabled], [Enabled] Select whether to enable or disable Wake from PCIE Device.

Resume By RTC Alarm [Disabled], [Enabled] Select whether to enable or disable Wake Up on Alarm, to turn

on your system on a special day of the month.

EUP Power Saving
Mode

[Disabled], [Enabled] Select whether to enable or disable EUP power saving mode.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 62

Figure 26: BIOS Power Setup Menu - WatchDog Timer Configuration

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

WatchDog Timer Configuration

WDT Function [Disabled]

→ ←: Select Screen

↑ ↓: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

WDT Function [Disabled], [Enabled] Select whether to enable or disable WatchDog Timer function.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 63

12.2.4. Boot Setup Menu

The boot setup menu lists the for boot device priority order, that is generated dynamically.

Figure 27: BIOS Boot Setup Menu

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Boot Configuration

Full Screen LOGO Display [Disabled]

Setup Prompt Timeout 1

→ ←: Select Screen

Bootup NumLock State [On]

↑ ↓: Select Item

Enter: Select

CSM Support [Enabled] +/-: Change Opt.

Boot Option Filter [Legacy Only] F1: General Help

F2: Previous Values

Boot Option Priorities F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Option Description

Full Screen LOGO
Display

[Disabled], [Enabled] Select whether to enable or disable to display logo screen.

Bootup NumLock
State

[On], [Off] Select the state of the NumLock feature of the keyboard after

Startup.
[On]: The keys on the keypad will act as numeric keys.
[Off]: The keys on the keypad will act as cursor keys.

CSM Support [Enabled], [Disabled] Select whether to enable or disable CSM support.

Boot Option Filter [UEFI and Legacy],

[Legacy only], [UEFI
only]

Control Legacy / UEFI ROMs priority.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 64

12.2.5. Security Setup Menu

The Security setup menu provides information about the passwords and functions for specifying the security settings.
The passwords are case-sensitive. The KBox E-200 Series provides no factory-set passwords.

If there is already a password installed, the system asks for this first. To clear a
password, simply enter nothing and acknowledge by pressing <RETURN>. To set a
password, enter it twice and acknowledge by pressing <RETURN>.

Figure 28: BIOS Security Setup Menu

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Password Description

If ONLY the Administrator’s password is set, then this only limits access to
Setup and is only asked for when entering Setup

If ONLY the User’s password is set, then this is a power on password and
must be entered to boot or enter Setup. In Setup the User will have
Administrator rights

The password length must be in the following range:

→ ←: Select Screen

Minimum Length 3

↑ ↓: Select Item

Maximum length 20 Enter: Select

+/-: Change Opt.

Administrator Password F1: General Help

User Password F2: Previous Values

F3: Optimized Defaults

Boot Security Menu F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Description

Administrator Password Set administrator password

User Password Set user password

If only the administrator’s password is set, then only access to setup is limited. The
password is only entered when entering setup.

If only the user’s password is set, then the password is a power on password and must
be entered to boot or enter setup. Within the setup menu the user has administrator
rights.

Password length requirements are maximum 20 characters and minimum 3 characters.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 65

12.2.5.1. Remember the password

It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords results in being
locked out of the system.

If the system cannot be booted because the User Password or the Supervisor Password are not know, contact
Kontron Support for further assistance.

HDD security passwords cannot be cleared using the above method.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 66

12.2.6. Save & Exit Setup Menu

The exit setup menu provides functions for handling changes made to the UEFI BIOS settings and the exiting of the
setup program.

Figure 29: BIOS Save & Exit Setup Menu

BIOS SETUP UTILITY

Main Advanced Power Boot Security Save & Exit

Save Changes and Reset

Discard Changes and Reset

→ ←: Select Screen

Save Options

↑ ↓: Select Item

Save Changes Enter: Select

Discard Changes +/-: Change Opt.

F1: General Help

Restore Defaults F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.15.1234. Copyright (C) 2012, American Megatrends, Inc.

Feature Description

Save Changes and
Exit

Exit system setup after saving the changes. Once you are finished making your
selections, choose this option from the Exit menu to ensure the values you selected are
saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and
stays on even when the PC is turned off. When you select this option, a confirmation
window appears. Select [Yes] to save changes and exit.

Discard Changes and
Exit

Exit system setup without saving any changes. Select this option only if you do not want
to save the changes that you made to the Setup program. If you made changes to fields
other than system date, system time, and password, the BIOS asks for a confirmation
before exiting.

Save Changes Save changes done so far to any of the setup values. This option allows you to save the

selections you made. After selecting this option, a confirmation appears. Select [Yes] to
save any changes.

Discard Changes Discards changes done so far to any of the setup values. This option allows you to

discard the selections you made and restore the previously saved values. After selecting
this option, a confirmation appears. Select [Yes] to discard any changes and load the
previously saved values.

Restore Defaults Restore Default values for all the setup values. This option allows you to load optimal

default values for each of the parameters on the Setup menus, which will provide the
best performance settings for your system. The F9 key can be used for this operation.

KBox E-200 Series - User Guide, Rev. 1.0

www.kontron.com

// 67

Appendix A: List of Acronyms

The following table does not contain the complete acronyms used in signal names,
signal type definitions or similar. A description of the signals is included in the I/O
Connector and Internal connector chapters within this user guide.

Table 18: List of Acronyms

2D Two-Dimensional

3D Three-Dimensional

AT Advanced Technology

ATX Advanced Technology eXtended

BGA Ball Grid Array

BIOS Basic Input / Output System

BSP Board Support Package

CMOS Complementary Metal Oxide

Semiconductor

CPU Central Processing Unit

DC Direct Current

DDC Display Data Channel

DIO Digital Input / Output

ECC Error-Correcting Code

EEE Electrical and Electronic Equipment

EOS Electrical OverStress

ESD ElectroStatic Discharge

GbE Gigabit Ethernet

HDD Hard Disk Drive

HDMI High Definition Multimedia Interface

LAN Local Area Network

LED Light Emitting Device

LVDS Low-Voltage Differential Signaling

ME F/W Management Engine Firmware

mPCIe mini Peripheral Component Interconnect

express

PC-AT Personal Computer - Advanced

Technology

PCB Printed Circuit Board

PSU Power Supply Unit

PVC PolyViny Chloride

PWM Pulse Width Modulation

RAM Random Access Memory

ROM Read-Only Memory

RTC Real-Time Clock

SATA Serial Advanced Technology Attachment

SDP Serial Download Protocol

SELV Safety Extra-Low Voltage

SIM Subscriber Identity Module

SMBus System Management Bus

SoC System on Chip

SO-DIMM Small Outline Dual In-line Memory

Module

SPD Serial Presence Detect

SPI Serial Peripheral Interface

TDP Thermal Design Power

TPM Trusted Platform Module

UEFI Unified Extensible Firmware Interface

USB Universal Serial Bus

UTP Update Transfer Protocol

VGA Video Graphics Array

WDT WatchDog Timer

WEEE Waste Electrical and Electronic

Equipment

KBox E-200 Series – User Guide, Rev. 1.0

www.kontron.com

// 68

About Kontron

Kontron is a global leader in embedded computing technology (ECT). As a part of technology group S&T,
Kontron offers a combined portfolio of secure hardware, middleware and services for Internet of
Things (IoT) and Industry 4.0 applications. With its standard products and tailor-made solutions based
on highly reliable state-of-the-art embedded technologies, Kontron provides secure and innovative
applications for a variety of industries. As a result, customers benefit from accelerated time-to-market,
reduced total cost of ownership, product longevity and the best fully integrated applications overall.
Kontron is a listed company. Its shares are traded in the Prime Standard segment of the Frankfurt Stock
Exchange and on other exchanges under the symbol "KBC". For more information, please visit:

www.kontron.com



CORPORATE OFFICES

EUROPE, MIDDLE EAST
& AFRICA

NORTH AMERICA

ASIA PACIFIC

Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
Tel.: + 49 821 4086-0
Fax: + 49 821 4086-111
[e-mail]

9477 Waples Street
San Diego, CA 92121
USA
Tel.: + 1 888 294 4558
Fax: + 1 858 677 0898
[e-mail]

1~2F, 10 Building, No. 8 Liangshuihe 2nd Street,
Economical & Technological Development Zone,
Beijing, 100176, P.R. China
Tel.: + 86 10 63751188
Fax: + 86 10 83682438
[e-mail]