Kontron CP6003-SA User Manual

Page 1
» User Guide «
CP6003-SA
6U CompactPCI Processor Board based on
the 2
nd
Generation Intel® Core™ i7/i5 Processor with
Doc. ID: 1044-9757, Rev. 2.0
September 15, 2011
P R E L I M I N A R Y
If it’s embedded, it’s Kontron.
Page 2
Preface CP6003-SA

Revision History

Publication Title:
Doc. ID: 1044-9757
Rev. Brief Description of Changes Date of Issue
1.0 Initial issue 22-Jul-2011
2.0 General update 15-Sep-2011
CP6003-SA: 6U CompactPCI Processor Board based on the 2nd Genera­tion Intel® Core™ i7/i5 Processor with the Intel® QM67 Express Chipset

Imprint

Kontron Modular Computers GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Modular Computers GmbH +49 (0) 800-SALESKONTRON Sudetenstraße 7 sales@kontron.com D - 87600 Kaufbeuren Germany
P R E L I M I N A R Y
For further information about other Kontron products, please visit our Internet website: www.kontron.com.

Disclaimer

Copyright © 201 1 Kontron AG. All righ ts reserved. All dat a is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective own­ers and are recognized. Specifications are subject to change without notice.
Page ii ID 1044-9757, Rev. 2.0
Page 3
CP6003-SA Preface

Table of Contents

Revision History .........................................................................................................ii
Imprint ........................................................................................................................ii
Disclaimer ..................................................................................................................ii
Table of Contents ......................................................................................................iii
List of Tables .............................................................................................................ix
List of Figures ...........................................................................................................xi
Proprietary Note ......................................................................................................xiii
Trademarks .............................................................................................................xiii
Environmental Protection Statement .......................................................................xiii
Explanation of Symbols ..........................................................................................xiv
For Your Safety ........................................................................................................xv
High Voltage Safety Instructions ..........................................................................xv
Special Handling and Unpacking Instructions .....................................................xv
General Instructions on Usage ...............................................................................xvi
Two Year Warranty .................................................................................................xvii
1. Introduction ............................................................................. 1 - 3
1.1 Board Overview .......................................................................................1 - 3
1.2 Board-Specific Information ......................................................................1 - 4
1.3 System Expansion Capabilities ...............................................................1 - 5
1.3.1 PMC Module ...................................................................................1 - 5
1.3.2 XMC Module ...................................................................................1 - 5
1.3.3 CP6003-SA-MK2.5SATA Assembly Kit ...........................................1 - 5
1.3.4 SATA Flash Module ........................................................................1 - 5
1.3.5 Rear I/O Module .............................................................................1 - 5
1.4 Board Diagrams ......................................................................................1 - 5
1.4.1 Functional Block Diagram ...............................................................1 - 6
1.4.2 Front Panels ...................................................................................1 - 7
1.4.3 Board Layout ..................................................................................1 - 8
1.5 Technical Specification ..........................................................................1 - 10
1.6 Standards ..............................................................................................1 - 16
1.7 Related Publications .............................................................................1 - 17
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page iii
Page 4
Preface CP6003-SA
2. Functional Description ............................................................2 - 3
2.1 Processor .................................................................................................2 - 3
2.2 Memory ....................................................................................................2 - 4
2.3 Intel® QM67 Express Chipset .................................................................2 - 4
2.4 Timer ........................................................................................................2 - 5
2.5 Watchdog Timer ......................................................................................2 - 5
2.6 Battery .....................................................................................................2 - 5
2.7 Reset .......................................................................................................2 - 5
2.8 Flash Memory ..........................................................................................2 - 6
2.8.1 SPI Boot Flash for uEFI BIOS .........................................................2 - 6
2.8.2 Serial ATA Flash Module (Optional) ................................................2 - 6
2.9 Trusted Platform Module 1.2 (On Request) .............................................2 - 6
2.10 Board Interfaces ......................................................................................2 - 7
2.10.1 Front Panel LEDs ............................................................................2 - 7
2.10.1.1 IPMI and Hot Swap LEDs .......................................................2 - 7
2.10.1.2 Watchdog and Temperature Status LEDs ...............................2 - 8
2.10.1.3 General Purpose LEDs ...........................................................2 - 9
2.10.2 DIP Switches SW1, SW2 and SW3 ..............................................2 - 11
2.10.3 USB Interfaces ..............................................................................2 - 11
2.10.3.1 USB Connectors J6 and J7 ..................................................2 - 12
2.10.4 Integrated Graphics Controller ......................................................2 - 12
2.10.4.1 Graphics Memory Usage ......................................................2 - 12
2.10.4.2 Analog VGA Connector ........................................................2 - 13
2.10.5 COM Ports .....................................................................................2 - 14
P R E L I M I N A R Y
2.10.6 Gigabit Ethernet ............................................................................2 - 15
2.10.7 Serial AT A Interface .......................................................................2 - 16
2.10.7.1 Serial ATA Connector J14 .....................................................2 - 16
2.10.8 PMC Interface ...............................................................................2 - 17
2.10.8.1 PMC Connectors J21, J22, J23 and J24 Pinout ...................2 - 19
2.10.9 XMC Interface ...............................................................................2 - 21
2.10.10Debug Interface .............................................................................2 - 22
2.10.11 CompactPCI Interface ...................................................................2 - 22
2.10.11.1 Board Functionality when Installed in System Slot ...............2 - 22
2.10.11.2 Board Functionality when Installed in Peripheral Slot ...........2 - 23
Page iv ID 1044-97 57, Rev. 2.0
Page 5
CP6003-SA Preface
2.10.11.3 Packet Switching Backplane (PICMG 2.16) .........................2 - 23
2.10.11.4 Hot Swap Support ................................................................2 - 23
2.10.11.5 Power Ramping ....................................................................2 - 23
2.10.11.6 Precharge .............................................................................2 - 23
2.10.11.7 Handle Switch ......................................................................2 - 23
2.10.11.8 ENUM# Interrupt ..................................................................2 - 23
2.10.11.9 Hot Swap LED ......................................................................2 - 23
2.10.12 CompactPCI Bus Connector .........................................................2 - 24
2.10.12.1 CompactPCI Connector Keying ...........................................2 - 24
2.10.12.2 CompactPCI Connectors J1 and J2 Pinout ..........................2 - 25
2.10.12.3 CompactPCI Rear I/O Connectors J3-J5 and Pinout ...........2 - 29
3. Installation ............................................................................... 3 - 3
3.1 Safety Requirements ...............................................................................3 - 3
3.2 CP6003-SA Initial Installation Procedures ..............................................3 - 4
3.3 Standard Removal Procedures ...............................................................3 - 5
3.4 Hot Swap Procedures ............................................................................. 3 - 6
3.4.1 System Master Hot Swap ...............................................................3 - 6
3.4.2 Peripheral Hot Swap Procedure .....................................................3 - 6
3.5 Installation of CP6003-SA Peripheral Devices ........................................3 - 8
3.5.1 USB Device Installation ..................................................................3 - 9
3.5.2 SATA Flash Module Installation ...................................................... 3 - 9
3.5.3 Installation of External Serial ATA Devices .....................................3 - 9
3.5.4 Onboard 2.5” HDD/SSD Installation ...............................................3 - 9
3.6 PMC/XMC Module Installation ..............................................................3 - 10
3.6.1 Rear I/O Device Installation ..........................................................3 - 10
3.7 Battery Replacement ............................................................................. 3 - 11
3.8 Software Installation ..............................................................................3 - 12
P R E L I M I N A R Y
4. Configuration ........................................................................... 4 - 3
4.1 DIP Switches SW1, SW2 and SW3 Configuration ..................................4 - 3
4.1.1 DIP Switch SW1 Configuration .......................................................4 - 3
4.1.2 DIP Switches SW2 and SW3 Configuration ...................................4 - 4
ID 1044-9757, Rev. 2.0 Page v
Page 6
Preface CP6003-SA
4.2 Jumper Description ..................................................................................4 - 5
4.2.1 COMB Termination Jumper Settings ...............................................4 - 5
4.3 I/O Address Map ......................................................................................4 - 6
4.4 CP6003-SA-Specific Registers ................................................................4 - 7
4.4.1 Status Register 0 (STAT0) ...............................................................4 - 7
4.4.2 Status Register 1 (STAT1) ...............................................................4 - 8
4.4.3 Control Register 0 (CTRL0) ............................................................4 - 9
4.4.4 Control Register 1 (CTRL1) ............................................................4 - 9
4.4.5 Device Protection Register (DPROT) ............................................4 - 10
4.4.6 Reset Status Register (RSTAT) .....................................................4 - 11
4.4.7 Board Interrupt Configuration Register (BICFG) ...........................4 - 12
4.4.8 Status Register 2 (STAT2) .............................................................4 - 13
4.4.9 Board ID High Byte Register (BIDH) .............................................4 - 13
4.4.10 Board and PLD Revision Register (BREV) ...................................4 - 14
4.4.11 Geographic Addressing Register (GEOAD) ..................................4 - 14
4.4.12 Watchdog Timer Control Register (WTIM) ....................................4 - 15
4.4.13 Board ID Low Byte Register (BIDL) ..............................................4 - 17
4.4.14 LED Configuration Register (LCFG) .............................................4 - 18
4.4.15 LED Control Register (LCTRL) .....................................................4 - 19
4.4.16 IPMI Keyboard Controller Style Interface ......................................4 - 19
5. Power Considerations .............................................................5 - 3
5.1 System Power ..........................................................................................5 - 3
P R E L I M I N A R Y
5.1.1 CP6003-SA Baseboard ...................................................................5 - 3
5.1.2 Backplane .......................................................................................5 - 4
5.1.3 Power Supply Units .........................................................................5 - 4
5.1.3.1 Start-Up Requirement .............................................................5 - 4
5.1.3.2 Power-Up Sequence ...............................................................5 - 4
5.1.3.3 Tolerance ................................................................................5 - 5
5.1.3.4 Regulation ...............................................................................5 - 5
5.2 Power Consumption ................................................................................5 - 6
5.2.1 Power Consumption of the CP6003-SA Accessories .....................5 - 8
5.2.2 Power Consumption per Gigabit Ethernet Port ...............................5 - 8
5.3 Maximum Power Consumption of PMC/XMC Module ............................5 - 8
Page vi ID 1044-9757, Rev. 2.0
Page 7
CP6003-SA Preface
6. Thermal Considerations ......................................................... 6 - 3
6.1 Board Internal Thermal Monitoring ..........................................................6 - 3
6.2 Processor Thermal Monitoring ................................................................6 - 3
6.2.1 Digital Thermal Sensor (DTS) .........................................................6 - 3
6.2.2 Adaptive Thermal Monitor ...............................................................6 - 4
6.2.2.1 Frequency/sVID Control ........................................................6 - 4
6.2.2.2 Clock Modulation ....................................................................6 - 4
6.2.3 Catastrophic Cooling Failure Sensor .............................................6 - 5
6.3 Chipset Thermal Monitor Feature ............................................................6 - 5
6.4 External Thermal Regulation ...................................................................6 - 6
6.4.1 Operational Limits for the CP6003-SA ............................................6 - 8
6.4.2 Peripherals ......................................................................................6 - 9
A. CP6003-SA-MK2.5-SATA Assembly Kit .................................A - 3
A.1 MMADP-SATA01 Module Overview ........................................................A - 3
A.2 Technical Specifications ..........................................................................A - 3
A.3 MMADP-SATA01 Module Layout ............................................................A - 4
A.4 SATA Connector J2 .................................................................................A - 5
B. SATA Flash Module .................................................................B - 3
B.1 Technical Specifications ..........................................................................B - 3
B.2 SATA Flash Module Layout .....................................................................B - 4
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page vii
Page 8
Preface CP6003-SA
This page has been intentionally left blank.
P R E L I M I N A R Y
Page viii ID 1044-9757, Rev. 2.0
Page 9
CP6003-SA Preface

List of Tables

1-1 CP6003-SA Main Specifications .............................................................. 1 - 10
1-2 Standards ................................................................................................ 1 - 16
1-3 Related Publications ................................................................................ 1 - 17
2-1 Features of the Processors Supported on the CP6003-SA ....................... 2 - 4
3 IPMI and Hot Swap LEDs Function ........................................................... 2 - 7
2-1 Watchdog and Temperature Status LEDs Function ................................... 2 - 8
2-2 General Purpose LED Function ................................................................. 2 - 9
2-3 POST Code Sequence ............................................................................ 2 - 10
2-4 POST Code Example .............................................................................. 2 - 10
2-5 DIP Switch SW1 Function ....................................................................... 2 - 11
2-6 DIP Switch SW2 Function ....................................................................... 2 - 11
2-7 DIP Switch SW3 Function ....................................................................... 2 - 11
2-8 USB Connectors J6 and J7 Pinout .......................................................... 2 - 12
2-9 D-Sub VGA Connector J9 Pinout ............................................................ 2 - 13
2-10 Serial Connector J8 (COMA) Pinout ........................................................ 2 - 14
2-11 Pinout of GbE Connectors J10, J11 and J12 ........................................... 2 - 15
2-12 SATA Connector J14 Pinout .................................................................... 2 - 16
2-13 PMC PCI/PCI-X Configuration ................................................................ 2 - 17
2-14 PMC Connectors J22 and J24 Pinout ..................................................... 2 - 19
2-15 PMC Connectors J21 and J23 Pinout ..................................................... 2 - 20
2-16 XMC Connector J20 Pinout ..................................................................... 2 - 21
2-17 CompactPCI PCI/PCI-X Configuration .................................................... 2 - 22
2-18 CompactPCI Bus Connector J1 System Slot Pinout ............................... 2 - 25
2-19 CompactPCI Bus Connector J1 Peripheral Slot Pinout ........................... 2 - 26
2-20 64-bit CompactPCI Bus Connector J2 System Slot Pinout ..................... 2 - 27
2-21 64-bit CompactPCI Bus Connector J2 Peripheral Slot Pinout ................. 2 - 28
P R E L I M I N A R Y
2-22 CompactPCI Rear I/O Connector J3 Pinout ............................................ 2 - 29
2-23 CompactPCI Rear I/O Connector J3 Signals ........................................... 2 - 30
2-24 CompactPCI Rear I/O Connector J4 Pinout ............................................ 2 - 31
2-25 CompactPCI Rear I/O Connector J5 Pinout ............................................ 2 - 32
2-26 CompactPCI Rear I/O Connector J5 Signals ........................................... 2 - 33
4-1 DIP Switch SW1 for Boot Configuration .................................................... 4 - 3
ID 1044-9757, Rev. 2.0 Page ix
Page 10
Preface CP6003-SA
4-2 DIP Switch SW2 for CompactPCI Interface Configuration ......................... 4 - 4
4-3 DIP Switch SW3 for PMC Interface Configuration ..................................... 4 - 4
4-4 JP2 Jumper Setting for RS-422 TXD Termination (COMB) ....................... 4 - 5
4-5 JP3 Jumper Setting for RS-422 RXD Termination (COMB) ....................... 4 - 5
4-6 I/O Address Map ........................................................................................ 4 - 6
4-7 Status Register 0 (STAT0) .......................................................................... 4 - 7
4-8 Status Register 1 (STAT1) .......................................................................... 4 - 8
4-9 Control Register 0 (CTRL0) ....................................................................... 4 - 9
4-10 Control Register 1 (CTRL1) ....................................................................... 4 - 9
4-11 Device Protection Register (DPROT) ....................................................... 4 - 10
4-12 Reset Status Register (RSTAT) ................................................................ 4 - 11
4-13 Board Interrupt Configuration Register (BICFG) ...................................... 4 - 12
4-14 Status Register 2 (STAT2) ........................................................................ 4 - 13
4-15 Board ID High Byte Register (BIDH) ........................................................ 4 - 13
4-16 Board and PLD Revision Register (BREV) .............................................. 4 - 14
4-17 Geographic Addressing Register (GEOAD) ............................................. 4 - 14
4-18 Watchdog Timer Control Register (WTIM) ............................................... 4 - 16
4-19 Board ID Low Byte Register (BIDL) ......................................................... 4 - 17
4-20 LED Configuration Register (LCFG) ........................................................ 4 - 18
4-21 LED Control Register (LCTRL) ................................................................ 4 - 19
5-1 Maximum Input Power Voltage Limits ........................................................ 5 - 3
5-2 DC Operational Input Voltage Ranges ....................................................... 5 - 3
5-3 Input Voltage Characteristics ..................................................................... 5 - 5
5-4 CP6003-SA in uEFI Shell Mode ................................................................. 5 - 7
P R E L I M I N A R Y
5-5 CP6003-SA with Win. XP and Processor and Graphics in Idle State ........ 5 - 7

5-6 CP6003-SA with Win. XP and Max. Proc. Workload and Basic Graphics Oper. 5 - 7 5-7 CP6003-SA with Win. XP and Maximum Processor and Graphics Workload ... 5 - 7

5-8 Power Consumption of CP6003-SA Accessories ...................................... 5 - 8
5-9 Power Consumption per Gigabit Ethernet Port ......................................... 5 - 8
5-10 PMC/XMC Module Current ........................................................................ 5 - 8
A-1 MMADP-SATA01 Main Specifications ....................................................... A - 3
A-2 SATA Connector J2 Pinout ........................................................................ A - 5
B-1 SATA Flash Module Main Specifications ................................................... B - 3
Page x ID 1044-9757, Rev. 2.0
Page 11
CP6003-SA Preface

List of Figures

1-1 CP6003-SA Functional Block Diagram .................................................... 1 - 6
1-2 CP6003-SA Front Panel .......................................................................... 1 - 7
1-3 CP6003-SA Board Layout – Top View .................................................... 1 - 8
1-4 CP6003-SA Board Layout – Bottom View ............................................... 1 - 9
2-1 USB Connectors J6 and J7 .................................................................... 2 - 12
2-2 D-Sub VGA Connector J9 ...................................................................... 2 - 13
2-3 Serial Connector J8 (COMA) ................................................................. 2 - 14
2-4 GbE Connectors J10, J11 and J12 ........................................................ 2 - 15
2-5 SATA Connector J14 .............................................................................. 2 - 16
2-6 PMC Connectors J21, J22, J23 and J24 ............................................... 2 - 18
2-7 XMC Connector J20 ............................................................................... 2 - 21
2-8 CompactPCI Connectors J1-J5 ............................................................. 2 - 24
3-1 Connecting a Peripheral Device to the CP6003-SA ................................ 3 - 8
4-1 DIP Switch SW1 ....................................................................................... 4 - 3
4-2 DIP Switches SW2 and SW3 ................................................................... 4 - 4
6-1 CP6003-SA with Intel® Quad-Core i7-2715QE (SV), 2.1 GHz ............... 6 - 8
6-2 CP6003-SA with Intel® Dual-Core i7-2655LE (LV), 2.2 GHz ................... 6 - 8
6-3 CP6003-SA with Intel® Dual-Core i5-2515E (SV), 2.5 GHz .................... 6 - 9
A-1 MMADP-SATA01 Module Layout ............................................................. A - 4
A-2 SATA Connector J2 .................................................................................. A - 5
B-1 SATA Flash Module Layout (Bottom View) .............................................. B - 4
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page xi
Page 12
Preface CP6003-SA
This page has been intentionally left blank.
P R E L I M I N A R Y
Page xii ID 1044-9757, Rev. 2.0
Page 13
CP6003-SA Preface

Proprietary Note

This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. However, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described herein, as seen fit by Kontron without further notice.

Trademarks

Kontron, the PEP logo and, if occurring in this manual, “CXM” are tr ademarks owned by Kontron, Kaufbeuren (Germany). In addition, this document may include names, company logos and trademarks, which are registered trademarks and, therefore, proprietary to their respective owners.

Environmental Protection Statement

This product has been manufactured to satisfy environmental protection requirements where possible. Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with applicable country, state, or local laws or regulations.
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page xiii
Page 14
Preface CP6003-SA

Explanation of Symbols

Caution, Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the pre­cautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material.
Please refer also to the section “High Voltage Safety Instructions” on the following page.
Warning, ESD Sensitive Device!
This symbol and title inform that electronic boards and their compo­nents are sensitive to static electricity. Therefore, care must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times.
Please read also the section “Special Handling and Unpacking Instructions” on the following page.
Warning!
This symbol and title emphasize points which, if not fully understood and taken into consideration by the reader, may endanger your health and/or result in damage to your material.
Note ...
This symbol and title emphasize aspects the reader should read through carefully for his or her own advantage.
P R E L I M I N A R Y
Page xiv ID 1044-9757, Rev. 2.0
Page 15
CP6003-SA Preface

For Your Safety

Y our new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation. Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines.

High Voltage Safety Instructions

Warning!
All operations on this device must be carried out by sufficiently skilled personnel only.
Caution, Electric Shock!
Before installing a not hot-swappable Kontron product into a system always ensure that your mains power is switched off. This applies also to the installation of piggybacks.
Serious electrical shock hazards can exist during all installation, repair and maintenance operations with this product. Therefore, always unplug the power cable and any other cables which provide external voltages before performing work.

Special Handling and Unpacking Instructions

ESD Sensitive Device!
Electronic boards and their components are sensitive to static elec­tricity. Therefore, care must be taken during all handling operations and inspections of this product, in order to ensure product integrity at all times.
Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is otherwise protected.
P R E L I M I N A R Y
Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands or tools. This is most easily done by touching a metal part of your system housing.
It is particularly important to observe standard anti-static precautions when changing piggy­backs, ROM devices, jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the board is not placed on conductive surfaces, including anti-static plas­tics or sponges. They can cause short circuits and damage the batteries or con ductive circuit s on the board.
ID 1044-9757, Rev. 2.0 Page xv
Page 16
Preface CP6003-SA

General Instructions on Usage

In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
This device should only be installed in or connected to systems that fulfill all necessary technical and specific environmental requirements. This applies also to the operational temperature range of the specific board version, which must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.
In performing all necessary installation and application operations, please follow only the instructions supplied by the present manual.
Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship the board, please re-pack it as nearly as possible in the manner in which it was delivered.
Special care is necessary when handling or unp acking the product. Please co nsult the special handling and unpacking instruction on the previous page of this manual.
P R E L I M I N A R Y
Page xvi ID 1044-9757, Rev. 2.0
Page 17
CP6003-SA Preface

Two Year Warranty

Kontron grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE
WARRANTY
implied by anyone on behalf of Kontron are valid unless the consumer has the expre ss written consent of Kontron.
Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase. This warranty is not transferable nor extendible to cover any other users or long-term storage of the product. It does not cover products which have been modified, altered or repaired by any other party than Kontron or their authorized agents. Furthermore, any product which has been, or is sus­pected of being damaged as a result of negligence , improper use, incorrect handling, servicing or maintenance, or which has been damaged as a result of excessive current/voltage or tem­perature, or which has had its serial number(s), any ot her markings or parts thereof altered, de­faced or removed will also be excluded from this warranty.
If the customer’s eligibility for warranty has not been voided, in the event of any claim, he may return the product at the earliest possible convenience to the original place of p urchase, togeth­er with a copy of the original document of purchase, a full description of the application the product is used on and a description of the defect. Pack the product in such a way as to ensure safe transportation (see our safety instructions).
as described in the following. However , no other warranties that may be granted or
Kontron provides for repair or replacement of any p art, assembly or su b-assembly at their own discretion, or to refund the original cost of purchase, if appropriate. In the event of repair, re­funding or replacement of any part, the ownership of the removed or replaced parts reverts to Kontron, and the remaining part of the original guarantee, or any new guarantee to cover the repaired or replaced items, will be transferred to cover the new or repaired items. Any exten­sions to the original guarantee are considered gestures of goodwill, and will be defined in the “Repair Report” issued by Kontron with the repaired or replaced item.
Kontron will not accept liability for any further claims resulting directly or indirectly from any warranty claim, other than the above specified repair, replacement or refunding. In particular, all claims for damage to any system or process in which the product was employed, or any loss incurred as a result of the product not functioning at any given time, are excluded. The extent of Kontron liability to the customer shall not exceed the original purchase price of the item for which the claim exists.
Kontron issues no warranty or representation, either explicit or implicit, with respect to its products’ reliability, fitness, quality, marketability or ability to fulfil any particular application or purpose. As a result, the products are sold “as is,” and the responsibility to ensure their suitability for any given task remains tha t of the purchaser. In no event will Kontron be liable for direct, indirect or consequential damages resulting from the use of our hardware or software products, or documentation, even if Kon tron were advised of the possibility of such claims prior to the purchase of the product or during any period since the date of its purchase.
Please remember that no Kontron employee, dealer or agent is authorized to make any modification or addition to the above specified terms, either verbally o r in any other form, written or electronically transmitted, without the company’s consent.
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page xvii
Page 18
Preface CP6003-SA
This page has been intentionally left blank.
P R E L I M I N A R Y
Page xviii ID 1044-9757, Rev. 2.0
Page 19
CP6003-SA Introduction
Chapter 1
1
Introduction
ID 1044-9757, Rev. 2.0 Page 1 - 1
P R E L I M I N A R Y
Page 20
Introduction CP6003-SA
This page has been intentionally left blank.
P R E L I M I N A R Y
Page 1 - 2 ID 1044-9757, Rev. 2.0
Page 21
CP6003-SA Introduction

1. Introduction

1.1 Board Overview

The CP6003-SA (S tandard Air-Cooled) is a highly integrated 6U CompactPCI system controller board based on the 2 Intel® QM67 Express chipset.
The board supports the 2
2.1 GHz, the 2
2.2 GHz, and the 2 All processors are built on 32-nm technology and provided in a BGA package.
Two SODIMM sockets are available on the CP6003-SA to provide up to 16 GB dual-channel, third-generation Double Data Rate (DDR3) memory with Error Ch ecking and Correction (ECC) running at 1333 MHz. The graphics controller and the memory controller are integrated in the processor. Furthermore, either one 2.5" HDD/SSD or up to 32 GB NAND flash memory (SSD) via a SATA Flash module can be integrated into the CP6003-SA.
For maximum application flexibility, the CP6003-SA comes with an extensive range of inter­faces such as up to five Gigabit Ethernet ports (t hree on fro nt I/ O a nd two on rear I/O in com­pliance with PICMG 2.16), three high-resolution graphics inter faces (VGA, 2 x HDMI/DVI), two COM ports (RS-232 on front and rear I/O, RS-422 on rear I/O), and six SATA interfaces with RAID 0/1/5/10 functionality , one for the onboard SA T A connector , one for th e SA T A Flash mod­ule or the 2.5" HDD/SSD, and four for rear I/O. In addition, six USB 2.0 port s are available on the board, two on front I/O and four on rear I/O.
Support for one PMC/XMC module ensures individual system expansion either via one 64-bit/
66 MHz PCI or 64-bit /133 MHz PCI-X PMC interface or via one XMC interface utilizing a x8
lane PCI Express 2.0 interconnection.
nd
generation Intel® Core™ i7 and i5 processors combined with the mobile
nd
nd
generation, dual-core, low-voltage Intel® Core™ i7-2655LE processor with
nd
generation, dual-core Intel® Core™ i5-2515E processor with 2.5 GHz.
generation, quad-core Intel® Core™ i7-2715QE processor with
The board supports a configurable 64-bit/66 MHz PCI or PCI-X hot swap CompactPCI inter­face. When installed in the system slot, the interface is enabled, and when installed in a periph­eral slot, the CP6003-SA is isolated from the CompactPCI bus.
Safety and security features via a Trusted Platform Module (TPM) 1.2 are provided on request. Intelligent Platform Management Interface (IPMI) is supported as well.
Designed for stability , the board fits into applications situated in industrial environments, includ­ing I/O intensive applications where only one slot is available for the CPU, making it a perfect core technology for long-life applications. Components with high temperature tolerance have been selected from embedded technology programs, and th erefore of fer long-term availability.
The board is offered with various Board Support Packages including Windows, VxWorks and Linux operating systems. For further information concerning the operating systems available for
,
the CP6003-SA
please contact Kontron.
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 3
Page 22
Introduction CP6003-SA

1.2 Board-Specific Information

The CP6003-SA is a CompactPCI single-board computer based on the 2nd generation Intel® Core™ i7 and i5 processors and specifically designed for use in highly integrated platforms with solid mechanical interfacing for a wide range of industrial environment applications.
Some of the CP6003-SA's outstanding features are:
Support for the following 2
Quad-core Intel® Core™ i7-2715QE (SV), 2.1 GHz, 6 MB L3 cache
Dual-core Intel® Core™ i7-2655LE (LV), 2.2 GHz, 4 MB L3 cache
Dual-core Intel® Core™ i5-2515E (SV), 2.5 GHz, 3 MB L3 cache
Intel® QM67 Express chipset
Up to 16 GB, dual-channel, DDR3 SDRAM memory with ECC running at 1333 MHz on two SODIMM sockets
Integrated 3D high-performance graphics controller with three high-resolution graphics in­terfaces (VGA / 2 x HDMI/DVI)
64-bit/66 MHz PCI or PCI-X CompactPCI interface (PICMG 2.0)
One PMC slot with PCI functionality and with rear I/O support; 64-bit/66 MHz PCI inter­face or 64-bit/133 MHz PCI-X interface
One XMC slot utilizing a x8 lane PCI Express 2.0 interconnection
Five Gigabit Ethernet interfaces:
Three Gigabit Ethernet interfaces on front I/O
Two Gigabit Ethernet interfaces on rear I/O (PICMG 2.16)
Two Gigabit Ethernet (GbE) controllers:
One Intel® 82579LM Gigabit Ethernet controller connected to one GbE port on the front panel
One Intel® 82580EB Quad Gigabit Ethernet controller connected to two GbE ports on
the front panel and two GbE ports on the rear I/O
Six Serial ATA interfaces with SATA RAID 0/1/5/10 support:
One onboard SATA 6 Gb/s interface for the standard SATA onboard connector
One onboard SATA 6 Gb/s interface for either one Serial ATA Flash module or one
Serial ATA 2.5" hard disk drive (HDD) / solid state drive (SSD)
Four SATA 3 Gb/s interfaces on the rear I/O
Six USB ports:
Two USB 2.0 ports on the front panel
Four USB 2.0 ports on the rear I/O
P R E L I M I N A R Y
Two COM ports:
One RS-232 COM port either on the front panel or on the rear I/O (COMA)
One RS-422 COM port on the rear I/O (COMB)
TCG 1.2 compliant Trusted Platform Module (TPM), on request
Two SPI boot flashes to provide firmware redundancy:
One standard SPI boot flash
One recovery SPI boot flash
Watchdog timer
Battery-backed real-time clock (RTC)
Three onboard DIP switches for board configuration
Supports PICMG Packet Switching Backplane Specification 2.16
IPMI support
4HP, 6U CompactPCI
Passive heat sink solution for forced-airflow cooling
Rear I/O on J3 and J5; optionally on J4 for PMC/XMC only
Hot swap capability: as system controller or as peripheral device
AMI Aptio®, a uEFI-compliant platform firmware
nd
generation processors:
Page 1 - 4 ID 1044-9757, Rev. 2.0
Page 23
CP6003-SA Introduction

1.3 System Expansion Capabilities

1.3.1 PMC Module

The CP6003-SA has a 3.3V, rear I/O capable PMC mezzanine inte rface configurable for ei­ther 64-bit / 6 6 MHz PCI or 64-bit/133 MHz PCI-X operation. This interface supports a wide range of PMC modules with PCI interface including all of Kontron’s PMC modules and pro­vides an easy and flexible way to configure the CP6003-SA for various application require­ments. For information on the PMC interface, refer to chapter 2.10.8, "PMC Interface".

1.3.2 XMC Module

The CP6003-SA has one XMC mezzanine interface for support of x1, x4 and x8 PCI Express
2.0 XMC modules providing an easy and flexible way to configure the CP6003-SA for various application requirements. For information on the XMC interface, refer to chap ter 2.1 0.9, "XMC Interface".

1.3.3 CP6003-SA-MK2.5SATA Assembly Kit

The CP6003-SA comes with an optional CP6003-SA-MK2.5SATA assembly kit comprised of one MMADP-SA T A01 module and the n ecessary components needed for mounting the module on the CP6003-SA. The MMADP-SATA01 module is required for connecting an onboard 2.5" Serial ATA HDD or SSD to the CP6003-SA via an onboard SATA extension connector . For fur­ther information concerning the MMADP-SATA01 module, please refer to Appendix A.

1.3.4 SAT A Flash Module

The CP6003-SA provides support for up to 32 GB NAND flash memory in combination with an optional SATA Flash module, which is connected to the CP6003-SA via an onboard SATA ex­tension connector. For further information concerning the SATA Flash module, please refer to Appendix B.

1.3.5 Rear I/O Module

The CP6003-SA provides support for one rear I/O module via the CompactPCI rear I/O con­nectors. For further information about the compatibility of rear I/O modules with the CP6003­SA, please refer to the CP6003-SA datasheet.

1.4 Board Diagrams

The following diagrams provide additional information concerning board functionality and component layout.
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 5
Page 24
Introduction CP6003-SA
VGA
Switch
Front Panel
cPCI
2x
USB
Debug
DMI 2.0
4x
USB
4x
SATA
SIO
Temp.
Sense
GbE
PCI 64/66 MHz
3.3V / 5V VIO
TH/
WD
HS
IPMB
COMA
RJ45
Hot
Swap
2.5"
SATA
SSD/HDD site
VGA CRT
1000BT
RJ-45
PCIe x8
PCI / PCIX
64/133 MHz
GbE
Mag.
DDR3 w ECC
SODIMM
memory
Channel A
2
nd
gen.
Intel®
Core™ i7/i5
DDR3 DDR3
Intel®
QM67
USB
DMI
SMB
SPI
PCIe
FDI
VGA
XDP
FDI
PCI
64/66MHz
DP to
HDMI /
DVI
2x
HDMI/DVI
ETH
2xDPUSB
SATA
7-pin
SATA
HDA
HDA
Mag.
PCIe
to
PCI/X
DDR3 w ECC
SODIMM
memory
Channel B
PCIe
to
PCI
Mag.
1000BT
RJ-45
Mag.
PMC/XMC
PCI / PCIX 64/133 MHz or
XMC PCIe x8
Rear I/O J4
VGA
CRT
RST
IPMI
1000BT
RJ-45
Mag.
to Rear I/O
PCIe
x4
COMBCOMA
GbE
PHY
Quad GbE
Controller
to Front I/O
to VGA
Switch
Redundant
FPGA
Board
Control
IPMI
Controller
EEP
EEP
Flash
FRU
from Quad GbE
Controller
PCIe
x4
uEFI
BIOS
Flash
TPM
LPC
LPC
LEDs
to
Front I/O
I
2
C
PCIe
x4
GP
DMI
FDI
PCIe
PCIe
(on request)
Bat. RTC
RS-422
RS-232

1.4.1 Functional Block Diagram

Figure 1-1: CP6003-SA Functional Block Diagram
P R E L I M I N A R Y
Page 1 - 6 ID 1044-9757, Rev. 2.0
Page 25
CP6003-SA Introduction

1.4.2 Front Panels

Figure 1-2: CP6003-SA Front Panel
Legend:
IPMI LEDs
I0/I1 (red/green): Indicate the software status
of the IPMI controller
Status LEDs
WD (green): Watchdog Status
TH (red/green): Temperature Status
HS (blue): Hot Swap Control
General Purpose LEDs
LED 0..3 (red/green/amber): General Purpose/POST code
Integral Ethernet LEDs
ACT (green): Ethernet Link/Activity
SPEED (green/orange/off): Ethernet Speed
Note ...
If the General Purpose LEDs are lit red during boot-up, a failure is indicated before the uEFI BIOS has started.
For further information, please contact Kontron.
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 7
Page 26
Introduction CP6003-SA
1
J20
A1
F1
A19
F19
21
11
12
21
910
1234
J13
J5
J4
(optional)
J3
J2
J1
HS LED
Magnetics
J14
J22
J23
J24
12
63
12
63 64
12
PMC/XMC
IPMI/WD/TH LEDs
HDD/SSD
2nd gen.
Intel®
Core™ i7/i5
Intel® QM67
GP/POST Code LEDs
J21
12
63 64
63 64
64
J18
J19
SODIMM Socket
SODIMM Socket
Channel B
Channel A
12
12
Battery
Magnetics
GbE A
J10
GbE B
J11
GbE E
J12
COM
J8
VGA
J9
USB
J7
USB
J6
1
2
3334
SATA Flash Module/
MMADP-SATA01 Module
J17
J15
J16
ON
SW1
ON
ON

1.4.3 Board Layout

Figure 1-3: CP6003-SA Board Layout – Top View
P R E L I M I N A R Y
Page 1 - 8 ID 1044-9757, Rev. 2.0
Page 27
CP6003-SA Introduction
JP2
J25
JP3
JP1
Temperature Sensor
Figure 1-4: CP6003-SA Board Layout – Bottom View
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 9
Page 28
Introduction CP6003-SA

1.5 Technical Specification

Table 1-1: CP6003-SA Main Specifications
FEATURES SPECIFICATIONS
CPU
Memory Main Memory:
Processor and Memory
P R E L I M I N A R Y
The CP6003-SA supports the following 2
Quad-core Intel® Core™ i7-2715QE (SV), 2.1 GHz, 6 MB L3 cache
Dual-core Intel® Core™ i7-2655LE (LV), 2.2 GHz, 4 MB L3 cache
Dual-core Intel® Core™ i5-2515E (SV), 2.5 GHz, 3 MB L3 cache
Further processor features:
Up to four execution cores
Intel® Hyper-Threading Technology (Intel® HT Technology)
Intel® 64 Architecture
Intel® Advanced Vector Extensions (AVX) floating point
Intel® Turbo Boost Technology 2.0
Intel® Intelligent Power Sharing (IPS)
System memory interface with optimized support for dual-channel
DDR3 SDRAM memory at 1333 MHz with ECC
Integrated 2D and 3D Graphics Engines
DMI 2.0 with 5 GT/s and FDI interfaces to the Intel® QM67 chipset
One x8 and two x4 PCI Express 2.0 ports operating at 5 GT/s
Please contact Kontron for further information concerning the suitability of other Intel processors for use with the CP6003-SA.
Up to 16 GB, dual-channel DDR3 SDRAM memory with ECC running at
1333 MHz on two SODIMM sockets
Cache Structure:
64 kB L1 cache for each core
32 kB instruction cache
32 kB data cache
256 kB L2 shared instruction/data cache for each core
Up to 6 MB L3 shared instruction/data cache
Flash Memory:
Two redundant SPI flashes (2 x 8 MB) for uEFI BIOS and controlled by
the IPMI controller
Up to 32 GB NAND flash via an onboard Serial ATA Flash module (SSD)
Serial EEPROM with 64 kbit
nd
generation microprocessors:
Page 1 - 10 ID 1044-9757, Rev. 2.0
Page 29
CP6003-SA Introduction
Table 1-1: CP6003-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS
Intel® QM67 Mobile Intel® QM67 Express Chipset:
Two x4 or eight x1 PCI Express 2.0 ports operating at 5 GT/s (only one
x4 PCI Express port is used on the CP6003-SA)
SATA host controller with six ports and RAID 0/1/5/10 support
Two SATA 6 Gb/s ports accessible via onboard connectors
Four SATA 3 Gb/s ports accessible via rear I/O
USB 2.0 host interface with up to 14 USB ports available (only six ports
are used on the CP6003-SA)
Integrated Ethernet controller
SPI flash interface support
Chipset
Low Pin Count (LPC) interface
Power management logic support
Enhanced DMA controller, interrupt controller, and timer functions
System Management Bus (SMBus) compatible with most I²C™ devices
DMI 2.0 with 5 GT/s and FDI interfaces to the processor
High Definition Audio (HDA) interface
Analog display port
Three digital display ports
Integrated RTC
Graphics controller High-performance 3D graphics controller integrated in the processor:
Support for two independent displays
Supports analog displays (CRT) up to a resolution of 2048 x 1536
pixels with 32-bit color @ 75 Hz
Controller
Integrated
Supports digital displays (HDMI/DVI) up to a resolution of 1920 x
1200 pixels @ 60 Hz
Dynamic Video Memory Technology (DVMT)
CompactPCI
Compliant with CompactPCI Specification PICMG
2.0 R 3.0:
System controller operation
64-bit /66 MHz PCI or PCI-X master interface with dedicated PCIe-to-
PCI-X bridge
3.3V or 5V signaling levels (universal signaling support)
Compliant with the Packet Switching Specification PICMG 2.16. The CP6003-SA supports System Master hot swap functionality and applica-
tion-dependent hot swap functionality when used in a peripheral slot.
Interfaces
When used as a System Master, the CP6003-SA supports individual clocks for each slot and the ENUM signal handling is in compliance with the PICMG 2.1 Hot Swap Specification.
When installed in a peripheral slot, the CP6003-SA is isolated from the Com­pactPCI bus. It receives power from the backplane and supports rear I/O and, if the system supports it, packet switching (in this case up to two channels of Gigabit Ethernet).
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 11
Page 30
Introduction CP6003-SA
Table 1-1: CP6003-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS
Rear I/O The following interfaces are routed to the rear I/O connectors J3 and J5.
COMA (RS-232 signaling) and COMB (RS-422 signaling); no buffer on
the rear I/O module is necessary
4 x USB 2.0
1 x CRT VGA, 2 x HDMI/DVI
1 x HDA
2 x Gigabit Ethernet (compliant with PICMG 2.16, R 1.0)
4 x SATA 3 Gb/s
2 x GPIOs (on request)
The rear I/O connector J4 is optionally available and provides rear I/O inter­connection to the PMC/XMC interface.
Gigabit Ethernet
Five 10 Base-T/100 Base-TX/1000 Base-T Gigabit Ethernet interfaces based on one Intel® 82579LM Gigabit Ethernet controller and one Intel® 82580EB Quad Gigabit Ethernet controller:
Three RJ-45 connectors on the front panel
Two ports on the rear I/O (PICMG 2.16)
Automatic mode recognition (Auto-Negotiation)
Automatic cabling configuration recognition (Auto-MDI/X)
USB
Six USB ports supporting UHCI (USB 1.1) and EHCI (USB 2.0):
Two type A USB 2.0 connectors on the front panel
Four USB 2.0 ports on the rear I/O interface
Serial Two 16C550-compatible UARTs:
Interfaces
One RS-232 port on the front panel and routed to rear I/O, COMA
One RS-422 port on the rear I/O, COMB
PMC PMC interface:
Four onboard mezzanine connectors, (Jn1-Jn4), for connecting a stan-
dard PMC module
Up to 64-bit/66 MHz PCI or up to 64-bit/133 MHz PCI-X interface with
dedicated PCIe-to-PCI-X bridge
Only 3.3V PCI signaling voltage
Rear I/O supported through the CompactPCI connector J4 (optional)
P R E L I M I N A R Y
XMC XMC interface:
Supported voltages: 3.3 V, 5 V, +12 V, and -12 V
One onboard XMC connector (P15)
Up to x8 lanes PCI Express 2.0 ports operating at 5 GT/s
Rear I/O supported through the PMC connector (Jn4) to the
CompactPCI connector J4 (optional)
Serial ATA Two Serial ATA 6 Gb/s interfaces for:
Up to 32 GB flash memory via an onboard SATA Flash module, or
Onboard 2.5" hard disk drive (HDD) or solid state drive (SSD) is
supported in combination with the MMADP-SATA01 module
One standard SATA 6 Gb/s interface for the standard SATA connector
Four SATA 3 Gb/s ports accessible via rear I/O
Page 1 - 12 ID 1044-9757, Rev. 2.0
Page 31
CP6003-SA Introduction
Table 1-1: CP6003-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS
Front Panel Connectors VGA: 15-pin, D-Sub connector, J9
USB: two 4-pin, type A connectors, J6 and J7
Ethernet: three 8-pin, RJ-45 connectors, J10, J11 and J12
Serial port: one 8-pin, RJ-45 connector, J8 (COMA)
PMC/XMC front panel bezel cutout
Onboard Connectors
PMC connectors J21 - J24 (Jn1 - Jn4)
XMC connector, J20
Two SATA connectors
Sockets
One 7-pin, standard SATA connector, J14
One 34-pin, SATA extension connector, J17
JTAG connector, J16
Debug connector, J15
XDP-SFF (debug) connector, J25
CompactPCI Connectors J1 - J5, J4 optional
Two 204-pin DDR3 SODIMM sockets, J18 and J19
DIP Switches Three onboard DIP switches, SW1, SW2, and SW3, for board configuration Reset Switch One front panel hardware reset switch Hot Swap Switch One switch for hot swap purposes integrated in the front panel handle in
Switches
System LEDs System Status LEDs:
accordance with PICMG 2.1 Rev. 2.0.
I0/I1 (red/green): Indicate the software status of the IPMI
controller
WD (green): Watchdog Status
TH (red/green): Temperature Status
HS (blue): Hot Swap Control
LEDs
General Purpose LEDs:
LED 0..3 (red/green/amber): General Purpose/POST code
Ethernet LEDs Gigabit Ethernet Status on CP6003-SA:
ACT (green): Ethernet Link/Activity
SPEED (green/orange/off): Ethernet Speed
Watchdog Timer Software-configurable, two-stage Watchdog with programmable timeout
ranging from 125 ms to 4096 s in 16 steps
Serves for generating IRQ or hardware reset
System Timer
Timer
ID 1044-9757, Rev. 2.0 Page 1 - 13
The Intel® QM67 chipset contains three 8254-style counters which have
fixed uses
In addition to the three 8254-style counters, the Intel® QM67 chipset in-
cludes eight individual high-precision event timers that may be used by the operating system. They are implemented as a single counter each with its own comparator and value register.
P R E L I M I N A R Y
Page 32
Introduction CP6003-SA
Table 1-1: CP6003-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS
IPMI Controller NXP® ARM7 microcontroller with redundant 512 kB firmware flash and
automatic roll-back strategy
The IPMI controller carries out IPMI commands such as monitoring sev-
IPMI
eral onboard temperature conditions, board voltages and the power supply status, and managing hot swap operations.
The IPMI controller is accessible via two IPMBs (through the J1 and J2
connectors) and one host Keyboard Controller Style (KCS) Interface.
Thermal Management CPU and board overtemperature protection is provided by:
Temperature sensors integrated in the 2
cessor:
One temperature sensor for monitoring each processor core
One temperature sensor for monitoring the graphics core
Thermal
One temperature sensor for monitoring the package die temperature
One temperature sensor integrated in the Intel® QM67 chipset for mon-
itoring the chipset
One onboard temperature sensor for monitoring the board temperature
Specially designed heat sink
TPM Trusted Platform Module (TPM) 1.2 for enhanced hardware- and software-
based data and system security (on request)
Security
uEFI BIOS AMI Aptio®, AMI’s next-generation BIOS firmware based on the uEFI Specifi-
cation and the Intel Platform Innovation Framework for EFI.
LAN boot capability for diskless systems (standard PXE)
Redundant image; automatic fail-safe recovery in case of a damaged
image
Non-volatile storage of setting in the SPI flash (battery only required for
the RTC)
Compatibility Support Module (CSM) providing legacy BIOS compatibil-
ity based on AMIBIOS8
Command shell for diagnostics and configuration
uEFI shell commands executable from mass storage device in a Pre-OS
environment (open interface)
P R E L I M I N A R Y
Software IPMI IPMI firmware providing the following features:
Software
IPMI support in the command shell
The IPMI controller is accessible via up to two IPMBs, IOL and one KCS
interface with interrupt support
The IPMI firmware can be updated in field through all supported inter-
faces using the function “fwum...” of the open-source tool “ipmitool”. For further information on the ipmitool refer to the sourceforge.net website.
Two IPMI controller flash banks with automatic roll-back capability in
case of an upgrade firmware failure
Board supervision and control extensions such as board reset, power
and SPI flash control, etc.
Operating Systems
The board is offered with various Board Support Packages including Windows, VxWorks and Linux operating systems. For further information concerning the operating systems available for the CP6003-SA, please contact Kontron.
nd
gen. Intel® Core™ i7/i5 pro-
Page 1 - 14 ID 1044-9757, Rev. 2.0
Page 33
CP6003-SA Introduction
Note ...
When a battery is installed, refer to the operational specifica­tions of the battery as this determines the storage tempera­ture of the CP6003-SA (See "Battery" below).
Note ...
When additional components are installed, refer to their opera­tional specifications as this will influence the operational and stor­age temperature of the CP6003-SA.
Table 1-1: CP6003-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS
Mechanical 6U, 4HP, CompactPCI-compliant form factor Power Consumption See Chapter 5 for details. Temperature Ranges Operational: 0°C to +60°C Standard
-40°C to +70°C Extended without TPM
Storage: -55°C to +85°C Without hard dis k and without battery
General
Battery 3.0V lithium battery for RTC with battery socket.
Battery type: UL-approved CR2025 Temperature ranges: Operational: -20°C to +70°C typical (refer to the battery manufacturer ’s
specifications for exact range)
Storage: -55°C to +70°C typical (no discharge ) Climatic Humidity 93% RH at 40 °C, non-condensing (acc. to IEC 60068-2-78) Dimensions 233.35 mm x 160 mm Board Weight CP6003-SA: 775 g (with heat sink but without mezzanine cards)
P R E L I M I N A R Y
ID 1044-9757, Rev. 2.0 Page 1 - 15
Page 34
Introduction CP6003-SA

1.6 Standards

The board complies with the requirements of the following standards:
Table 1-2: Standards
TYPE ASPECT STANDARD REMARKS
CE Emission EN55022
EN61000-6-3
Immission EN55024
EN61000-6-2
Electrical Safety EN60950-1 -­Mechanical Mechanical Dimensions IEEE1101.10 -­Environmental Climatic Humidity IEC60068-2-78 93% RH at 40°C, non-condensing
WEEE Directive
2002/96/EC
RoHS Directive
2002/95/EC
Vibration
(Sinusoidal)
Single Shock IEC60068-2-27 Ruggedized version test parameters:
IEC60068-2-6 Ruggedized version test parameters:
--
--
(see note below)
Waste electrical and electronic equipment
Restriction of the use of certain hazardous sub­stances in electrical and electronic equipment
• 10-300 (Hz) frequency range
• 2 (g) acceleration
• 1 (oct/min) sweep rate
• 10 cycles/axis
• 3 axes
• 30 (g) acceleration
• 9 (ms) shock duration half sine
• 3 number of shocks per direction (total: 18)
• 6 directions
• 5 (s) recovery time
P R E L I M I N A R Y
Page 1 - 16 ID 1044-9757, Rev. 2.0
Permanent Shock IEC60068-2-29 Ruggedized version test parameters:
• 15 (g) acceleration
• 11 (ms) shock duration half sine
• 500 number of shocks per direction
• 6 directions
• 5 (s) recovery time
Page 35
CP6003-SA Introduction
Note ...
Kontron performs comprehensive environmental testing of it s products in accor­dance with applicable standards.
Customers desiring to perform further environmental testing of Kontron prod­ucts must contact Kontron for assistance prior to performing any such testing. This is necessary, as it is possible that environmental testing can be destructive when not performed in accordance with the applicable specifications.
In particular, for example, boards without conformal coating must not be exposed to a change of temperature exceeding 1K/ minute, averaged over a period of not more than five minutes. Otherwise, condensation may cause irre­versible damage, especially when the board is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destructive environmental testing.

1.7 Related Publications

The following publications contain information relating to this product.
Table 1-3: Related Publications
PRODUCT PUBLICATION
CompactPCI Systems and Boards
PMC Module IEEE 1386-2001, IEEE Standard for a Common Mezzanine Card (CMC) Family
XMC Module ANSI/VITA 42.0-200x XMC Switched Mezzanine Card Auxiliary Standard
Platform Firmware Unified Extensible Firmware Interface (uEFI) Specification, Version 2.1 All Kontron products Product Safety and Implementation Guide, ID 1021-9142 Kontron CP6003-SA uEFI BIOS User Guide
CompactPCI Specification PICMG 2.0, Rev. 3.0 CompactPCI Packet Switching Backplane Specification PICMG 2.16 Rev. 1.0 CompactPCI System Management Specification PICMG 2.9 Rev. 1.0 CompactPCI Hot Swap Specification PICMG 2.1 Rev. 2.0
IPMI - Intelligent Platform Management Interface Specification v2.0 Kontron CompactPCI Backplane Manual, ID 24229
IEEE 1386.1-2001, IEEE Standard Physical and Environmental Layers for PCI Mezzanine Cards (PMC)
ANSI/VITA 42.3-2006 XMC PCI Express Protocol Layer Standard
P R E L I M I N A R Y
CP6003-SA IPMI Firmware User Guide
ID 1044-9757, Rev. 2.0 Page 1 - 17
Page 36
Introduction CP6003-SA
This page has been intentionally left blank.
P R E L I M I N A R Y
Page 1 - 18 ID 1044-9757, Rev. 2.0
Loading...