Konica Minolta 7115, 7118 User Manual
Contents
Contents
1 Introduction
1.1 We Want You to Be a Satisfied Customer ..................................1-1
CE Marking (Declaration of Conformity).........................................1-1
1.2 SAFETY INFORMATION................................................................1-2
Warning and Precaution Symbols...................................................1-2
Meaning of Symbols........................................................................1-2
WARNING.......................................................................................1-3
CAUTION........................................................................................1-4
Precautions for Routine Use ...........................................................1-5
1.3 Safety Information......................................................................... 1-6
Laser Safety....................................................................................1-6
Internal Laser Radiation..................................................................1-6
LED Radiation Safety......................................................................1-8
Ozone Release...............................................................................1-8
Acoustic Noise ................................................................................1-8
1.4 About the User Manual.................................................................1-9
Explanation of Manual Conventions................................................1-9
[ ] key...............................................................................................1-9
1.5 Explanation of Basic Concepts and Symbols..........................1-10
Paper Feeding...............................................................................1-10
“Width” and “Length”.....................................................................1-11
Paper Orientation..........................................................................1-11
2 Precautions
2.1 Installation Precautions................................................................2-1
Installation site ................................................................................2-1
Power source ..................................................................................2-1
Space Requirements.......................................................................2-2
2.2 Operation Precautions..................................................................2-3
Operating Environment...................................................................2-3
Proper Use......................................................................................2-3
Transporting the Copier ..................................................................2-4
Care of Copier Supplies..................................................................2-4
2.3 Legal Restrictions on Copying ....................................................2-5
3 Before Making Copies
Konica 7115/7118 i
Contents
3.1 Available Features........................................................................ 3-1
3.2 Components and Their Functions ..............................................3-4
3.3 Parts Names and Their Functions ..............................................3-6
Copier.............................................................................................3-6
Inside the Copier ............................................................................3-8
Options...........................................................................................3-9
3.4 Control Panel ..............................................................................3-12
Names of Control Panel Parts and Their Functions.....................3-12
Icons on the Control Panel ...........................................................3-14
3.5 Turning ON and OFF and the Initial Mode................................3-15
How to Turn ON/OFF the Copier ..................................................3-15
When Copier is Turned ON..........................................................3-15
Default Settings............................................................................3-16
3.6 Useful Functions ........................................................................3-17
Panel Resetting............................................................................3-17
Auto Panel Reset..........................................................................3-17
Power Save..................................................................................3-18
Auto Shut OFF..............................................................................3-18
Auto Copy Start............................................................................3-18
Interrupting Copy Jobs .................................................................3-19
Auto Tray Switching......................................................................3-19
Account Number...........................................................................3-20
To enter an account number ........................................................3-20
Printing from the Personal Computer ...........................................3-21
Sending and Receiving Faxes Using the Copier ..........................3-21
3.7 Copy Paper..................................................................................3-22
Paper Specifications.....................................................................3-22
4 Loading Originals
4.1 Two Ways of Loading the Original..............................................4-1
Specific Types of Originals.............................................................4-1
4.2 Loading Originals in the Automatic Document Feeder ............ 4-2
Precautions for Using the Automatic Document Feeder ................4-2
Mixed Originals...............................................................................4-4
4.3 Place the Original on the Original Glass....................................4-6
Precautions for Placing the Original on the Original Glass............. 4-6
How to position a sheet original......................................................4-7
Highly Transparent Originals..........................................................4-8
Books..............................................................................................4-9
5 Making Copies
ii Konica 7115/7118
Contents
5.1 Copying..........................................................................................5-1
5.2 Selecting the Paper.......................................................................5-3
5.3 Feeding Paper Manually...............................................................5-5
Making Copies by Using the Bypass Tray ......................................5-6
5.4 Specifying the Zoom Ratio.........................................................5-11
Setting the Zoom Ratio .................................................................5-12
5.5 Adjusting the Image Density......................................................5-16
5.6 Interrupting a Copy Job..............................................................5-18
6 Advanced Copying
6.1 Making 1-Sided Copies .................................................................6-1
6.2 Output Copies (Sort and Group)..................................................6-5
Three Output Types........................................................................6-5
Sorting.............................................................................................6-6
Grouping.........................................................................................6-8
6.3 Erasing Part of Original Image (Erase) .....................................6-10
Precautions for Erase Position......................................................6-11
6.4 Reversing Original Tonal Arrangements..................................6-13
6.5 Providing a Image Shift ..............................................................6-14
Precautions for Image Shift Position.............................................6-14
7 Using the Utility Mode
7.1 User’s Choice ................................................................................7-2
Mixed Orig.......................................................................................7-6
Paper Priority ..................................................................................7-6
Copy Priority....................................................................................7-6
Density Priority................................................................................7-6
Density Level Priority (Auto)............................................................7-6
Density Level Priority (Manual).......................................................7-7
Output Priority.................................................................................7-7
Crisscross Mode.............................................................................7-7
4in1 Copy Order..............................................................................7-7
Book Binding Position .....................................................................7-7
Margin Setting.................................................................................7-7
Erase Setting (Left, Top, and Frame)..............................................7-8
Auto Panel Reset ............................................................................7-8
Power Save.....................................................................................7-8
Auto S hut OFF ................................................................................7-8
Density (ADF)..................................................................................7-8
Printer Density.................................................................................7-8
Paper Auto Detection......................................................................7-9
Konica 7115/7118 iii
Paper Size Detection......................................................................7-9
Paper Type (1st Tray).....................................................................7-9
Paper Type (Bypass Tray)..............................................................7-9
Special Paper Setting.....................................................................7-9
Making the User’s Choice Settings...............................................7-10
7.2 Drum Dehumidify........................................................................7-12
7.3 Toner Replenisher (Auxiliary Toner Replenishing)................. 7-13
7.4 Custom Size Input ......................................................................7-14
7.5 Administrator Mode....................................................................7-16
Administrator Mode ......................................................................7-16
Copy Track...................................................................................7-18
Disable Auto Shut OFF.................................................................7-26
7.6 Checking the Total Number of Copies/Prints Produced......... 7-28
7.7 Storing a Job...............................................................................7-30
8 Error Displays and Other Indicators
8.1 Major Error Displays and Remedial Actions..............................8-1
8.2 When the Add Paper Indicator Lights up................................... 8-4
Adding Paper..................................................................................8-4
8.3 When the Add Toner Indicator Lights up................................... 8-8
8.4 When the Paper Misfeed Indicator Lights................................8-11
Misfeed Indications and Misfeed Locations..................................8-11
Clearing a Paper Misfeed.............................................................8-12
Contents
9 Troubleshooting Tips
9.1 When This Type of Copy is Produced........................................9-1
9.2 When the Copier is not Operating Correctly.............................. 9-4
10 Appendix
10.1 Specifications.............................................................................10-1
Copier Konica 7115/7118.............................................................10-1
Automatic Document Feeder DF-217...........................................10-3
Paper Feed Unit PF-121...............................................................10-3
Shifting Unit IS-101.......................................................................10-4
Job Separator IT-102....................................................................10-4
Multiple Bypass Tray MT-102.......................................................10-4
10.2 Care of the Copier ......................................................................10-5
Cleaning .......................................................................................10-5
10.3 Function Combination Table.....................................................10-6
iv Konica 7115/7118
Contents
Function Combination Table .........................................................10-6
Conditions for Combined Functions..............................................10-6
10.4 List of Paper Sizes and Zoom Ratios........................................10-7
Paper Sizes...................................................................................10-7
Zoom Ratios (Original Size to Paper Size) ...................................10-8
Konica 7115/7118 v
Contents
vi Konica 7115/7118
Introduction
1 Introduction
1.1 We Want You to Be a Satisfied Customer
Thank you for choosing a Konica 7115/7118.
This User Manual describes the functions, operating procedures,
precautions, and basic troubleshooting for the Konica 7115/7118 copier.
Before using this copier, be sure to read the User Manual thoroughly in
order to ensure that you use the copier efficiently. After you have gone
throughthemanual,storeitin the holder on the rear sideof the copier and
keep it handy at all times.
Notethatsome of the illustrations of the machine used in theUserManual
may be different from what you actually see on your machine.
CE Marking (Declaration of Conformity)
This product complies with the following EU directives:
89/336/EEC, 73/23/EEC and 93/68/EEC directives.
This declaration is valid for the area of the European Union.
This device must be used with shielded interface cables. The use of nonshielded cable is likely to result in interference with radio communications
and is prohibited under EU directives.
1
Konica 7115/7118 1-1
1
1.2 SAFETY INFORMATION
This section contains detailed instructions on the operation and maintenance of this machine. To achieve optimum utility of this device, all operators should carefully read and follow the instructions in this manual.
Please keep this manual in a handy place near the machine.
Please readthe next section before usingthis device. It contains importantinformation
relatedto user safety and preventing equipmentproblems.
Make sure you observe all of the precautions listed in this manual.
* Please note thatsome parts of the contentsof this sectionmay not correspond withthe pur-
chased product.
Warning and Precaution Symbols
Introduction
WARNING:
CAUTION:
Meaning of Symbols
A triangleindicates a danger against which you should take precaution.
This symbol warns against possible electrical shock.
A diagonal line indicates a prohibited course of action.
This symbolwarns against dismantling the device.
A black circleindicates an imperative courseof action.
This symbolindicates you mustunplug the device.
Ignoringthis warningcould causeserious injuryor even death.
Ignoring this caution could cause injury or damage to property.
1-2 Konica 7115/7118
Introduction
WARNING
• Do not modify this product: Fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause
blindness.
• Do not attemptto remove thecovers and panelswhich have been fixedto
the product. Some products have a high-voltage part or a laser beam
sourceinside that could causean electrical shockor blindness.
• Use only the power cord supplied in the package.Failure to use this cord
couldresultinfireorelectricalshock.
• Use only thespecified power sourcevoltage. Failure to do so could result
in fire or electrical shock.
• Do not use a multipleoutlet adapter to connectany other appliances or
machines.Use of a power outlet for more than the markedcurrent value
couldresultinfireorelectricalshock.
Donot unplugand plug inthe powercord witha wethand: An electricalshock
couldresult.
Plug the powercord all the way into the power outlet.Failure to do so could
resultin fire or electrical shock.
• Do notscratch, abrade,place a heavyobject on,heat, twist,bend, pull on,
or damage the power cord. Use of a damaged power cord (exposed core
wire, broken wire, etc.)could result in fireor breakdown.
Shouldany of these conditions be found,immediatelyturn OFF the power
switch,unplug the power cord from the poweroutlet, and then call your
authorized servicerepresentative.
• In principle, do not use an extension cord. Use of an extension cord could
causefire or electricalshock. Contact yourauthorized service representative if an extension cord is required.
Do not place a flower vase or othercontainer that contains water,or metal
clipsor other small metallicobjects on this product.Spilled water or metallic
objects dropped inside the product could result in fire, electrical shock, or
break-down.
Shoulda pieceof m etal, water, or any othersimilar foreignmatter get inside
the product, immediately turn OFF the power switch,unplug the power cord
from the poweroutlet, and then call your authorized service representative.
• If this product becomes inordinately hot or emits smoke, or emits an unusualodor or noise,immediately turn OFF thepower switch, unplugthe power
cordfrom the poweroutlet, andthen callyour authorizedservicerepresentative.If you keep on using it as is, fire or electrical shockcould result.
• If this product has been dropped or its cover damaged, immediately turn
OFF the power switch, unplug the powercord from the power outlet,and
then callyour authorizedservice representative. If you keep onusing it as
is, fire or electrical shock could result.
Do not throw the toner cartridge or tonerinto an open flame. The hot toner
may scatter and cause burns or other damage.
1
Connectthe power cord only to an electrical outlet thatis equipped with a
grounding terminal.
Konica 7115/7118 1-3
1
CAUTION
Introduction
• Do not use flammable sprays, liquids, or gases near this product, as fire
couldresult.
• Do not leave a toner unitor drum unitin a place withineasy reach of
children.
Lickingor ingesting any of these substances couldinjure your health.
• Do not let any objectplug the ventilationholes of this product.Heat could
accumulate insidethe product, resulting in a fire or malfunction.
• Do not install this product at a site that is exposed to direct sunlight, or near
anairconditionerorheatingapparatus.Theresultanttemperature changes
insidethe product could causea malfunction,fire, or electricalshock.
• Do not place the product in a dusty place, or a site exposed to soot or
steam, near a kitchen table, bath, or a humidifier. Fire, electrical shock, or
breakdown could result.
• Do not place this product on an unstable or tilted bench, or in a location
subject to a lot of vibration and shock. It could drop orfall, causing personal
injuryor mechanical breakdown.
• Afterinstallingthis product,mount iton a secure base.If the unitmoves or
falls, it may cause personal injury.
• Do not store toner units and PC drum units near a floppy disk or watch that
are susceptible to magnetism. They couldcause these productsto malfunction.
The insideof this product has areas subjectto high temperature,which may
cause burns. When checkingthe insideof the unit formalfunctionssuch as a
paper misfeed, do nottouch the locations (aroundthe fusing unit,etc.) which
are indicated by a “Caution! High Temperature!”warning label.
Do not place any objects around the power plug, as the power plug may be
difficult to pull out when an emergency occurs.
• Alwaysuse thisproduct ina well ventilatedlocation.Operatingthe product
ina poorly ventilated room for an extendedperiodof time couldinjure your
health. Ventilate the room at regular intervals.
• Whenevermoving this product, be sure to disconnect the powercord and
othercables.Failure todo thiscould damagethe cordor cable,resultingin
fire, electrical shock, o r breakdown.
• When moving thisproduct, always holdit by the locations specified in the
User m anual or other documents.If the unit falls it may cause severepersonal injury. The product may also be damaged or malfunction.
• Remove the powerplug from the outlet at least twicea year and clean the
area between the plugterminals. Dustthat accumulatesbetween the plug
terminals could causea fire.
• When unplugging the power cord,be sure to holdonto the plug.Pullingon
the powercord could damage the cord, resulting in fireor electrical shock.
1-4 Konica 7115/7118
Introduction
Precautions for Routine Use
• Donot storetonerunits,PC drumunits,or other suppliesand consumables
in a place subjectto direct sunlightand high temperature or humidity, as
poor image quality and malfunction could result.
• Do not attemptto replace the toner unit and PC drum unitin a place exposedto directsunlight.If thePC drum is exposed tointense light,poorimage qualitycould result.
• Do not unpack a toner unitor PC drum unit until the very time of use. Do
not leavean unpacked unit standing.Install it immediately or poor image
quality could result.
• Do notkeep toner unitsand PC drum unitsin an uprightpositionor upside
down, as poor image quality could result.
• Do not throw or drop a tonerunit or PC drum unit,as poor image quality
couldresult.
• Do notuse thisproduct in an areawhere ammoniaor othergases orchemicalsare present. Failure to do so may shorten the service life of the product, cause damage or decrease performance.
• Do not use this product in an environment with a temperature outside the
rangespecifiedin the User manual,as breakdownor malfunctioncould result.
• Do not attemptto feed stapled paper, carbonpaper or aluminum foil
through this product, as malfunction or fire could result.
Do not touch or scratch the surface of the toner unit developing roller or the
PC drum, as poor imagequality could result.
Use the supplies and consumablesrecommended by the dealer.Use of any
supplyor consumablenotrecommended couldresultin poor imagequalityor
breakdown.
1
Konica 7115/7118 1-5
1
1.3 Safety Information
Laser Safety
This is a digital machine which operates using a laser. There is no
possibility o f danger from the laser provided the machine is operated
according to the instructions in this manual.
Since radiation emitted by the laser is completely confined within
protective housing, the laser beam cannot escape from the machine
during any phase of user operation.
This machine is certified as a Class 1 laser product: This means the
machine does not produce hazardous laser radiation.
Internal Laser Radiation
Maximum Average Radiation Power: 26.4 µW at the laser aperture of the
print head unit.
Wavelength: 770-795 nm
This product employs a Class 3b laser diode that emits an invisible laser
beam.
The laser diode and the scanning polygon mirror are incorporated in the
print head unit.
The print head unit is NOT A FIELD SERVICE ITEM:
Therefore, the print head unit should not be opened under any
circumstances.
Introduction
Print Head
1-6 Konica 7115/7118
Introduction
There is a laser aperture at the location shown above, which must,
however, NEVER be viewed directly by the user.
This is a semiconductorlaser. The maximum power of the laser diode is
5 mW and the wavelength is 770-795 nm.
Laser Aperture of the
Print Head Unit
CAUTION
Use of controls, adjustments or performance of procedures other than
those specified in this manual may result in hazardous radiation
exposure.
1
Konica 7115/7118 1-7
1
Introduction
LED Radiation Safety
Thisproductisacopierwhichoperates using a LED (light emitting diodes)
exposure system. There is no possibility of danger from LED optical
radiation, because the LED optical radiation level does not exceed the
accessible radiation limit of class 1 under all conditions of operation,
maintenance, service and failure.
Ozone Release
NOTE
= Locate the Machine in a Well Ventilated Room =
A negligible amount of ozone is generated during normal operation of
this machine. An unpleasant odor may,however,be created in poorly
ventilated rooms during extensive machine operations.For a comfortable, healthy, and safe operating environment, it is recommended that
the room well ventilated.
Acoustic Noise
For European Users
MachineNoise Regulation3 GSGV, 18.01.1991 : The sound pressurelev-
el at the operator position according to EN 27779 is equal to or less than
70dB(A).
1-8 Konica 7115/7118
Introduction
1.4 About the User Manual
Explanation of Manual Conventions
The marks and text formats used in this manual are described below.
WARNING
Failureto observeinstructionshighlightedinthismanner mayresult
in fatal or critical injuries.
➜ Observe all warnings in order to ensure safe use of the copier.
CAUTION
Failureto observeinstructionshighlightedinthismanner mayresult
in serious injuries or property damage.
➜ Observe all cautions in order to ensure safe use of the copier.
✎
1
Note
(* May also appear as “Important” or “Tip”)
Text highlighted in this manner containsuseful information and tips to
ensuresafe useofthecopier andserveas supplementaryinformation.
It is recommended that you read all of them.
1 The number 1 as formatted here in-
dicates the first step of a sequence
of actions.
2 Subsequent numbers as formatted
hereindicatesubsequentsteps of a
sequence of actions.
Text formatted in this style pro-
?
vides additional assistance.
➜ Textformattedin this style describes the action thatwill ensure the
desired results are achieved.
[ ] key
The names of keys on the control panel are written as shown above.
Konica 7115/7118 1-9
An illustration inserted here shows
what operations mustbe performed.
1
Introduction
1.5 Explanation of Basic Concepts and Symb ols
The use of words and symbols in this manual are explained below.
Paper Feeding
Duringprinting, paper is supplied from the right side of the copier and fed
into the Exit Tray on top with the printed surface of the page facing down.
The paper feed direction is shown by the arrows in the diagram below.
1-10 Konica 7115/7118
Introduction
“Width” and “Length”
Whenever paper dimensions are
mentionedin this manual,thefirstvalue
always refers to the width of the paper
(shownas “A” in the illustration)and the
second to the length (shown as “B”).
A: Width
B: Length
Paper Orientation
Lengthwise ( )
If the width (A) of the paper is shorter
than the length (B), the paper has a
verticalor portrait orientation, indicated
by either “L” or .
1
Crosswise ( )
If the width (A) of the paper is longer
than the length (B), the paper has a
horizontal or landscape orientation,
indicated by either “C” or .
Konica 7115/7118 1-11
1
Introduction
1-12 Konica 7115/7118
Precautions
2 Precautions
Observe the following precautions to keep the copier in the best possible
conditions.
2.1 Installation Precautions
Installation site
To ensure utmost safety and prevent possible malfunctions, install the
copier in a location that meets the following requirements:
- A location away from curtains, etc. that may catch fire and burn easily
- A location that is not exposed to water or other liquids
- A location free from direct sunlight
- A location out of the direct airflow of an air conditioner or heater, and
not exposed to extremely high or low temperatures
- A well-ventilated location
- A location that is not exposed to high humidity
- A location that is not extremely dusty
- A location not subjected to undue vibrations
- A stable and level location
- A location where ammonia or other organic gases are not generated
- A location that doesnot put the operator in the direct airflow of exhaust
from the copier
- A location that is not near any kind of heating devices
2
Power source
The power source requirements are as follows.
G Voltage Fluctuation: Within±10%
G Frequency Fluctuation: Within ± 3Hz
❍ Use a power source with as few voltage or frequency fluctuations as
possible.
Konica 7115/7118 2-1
2
Precautions
Space Requirements
To ensure easy copier operation, supply replacement, and maintenance,
adhere to the recommended space requirements detailed below.
<Konica 7115>
1038
959
1065
<Konica 7118>
1038
995
1524
✎
Note
Be sure to allow a clearance of 100 mm or more at the back of the
copier for the ventilation duct and 150 mm or more at the right of the
copier for the removal of the misfed papers.
Unit: mm
2-2 Konica 7115/7118
Precautions
2.2 Operation Precautions
Operating Environment
Theenvironmentalrequirementsforcorrectoperationof the copier are as
follows:
G Temperature:10°Cto30°C(50°Fto90°F)withfluctuationsof no more
than 10°C (18°F) within an hour
G Humidity:15% to 85% with fluctuations of no more than 10% within an
hour
Proper Use
To ensure the optimum performance of the copier, follow the precautions
listed below:
- Never place heavy objects on the Original Glass or subject it to
shocks.
- Never open any copier doors or turn OFF the copier while it is making
copies/printing, as a paper misfeed could r esult.
- Never bring any magnetized object, or use flammable sprays or
liquids, near the copier.
✚ Always make sure that the power plug is completely plugged into the
electrical output.
- Always make sure that the copier’s power plug is visible and not
hidden by the copier.
✚ Always unplug the copier from the electrical outlet if the copier is not
to be used for a long period of time.
✚ Always provide good ventilation when making a large number of
continuous copies/printed pages.
2
CAUTION
A negligible amount of ozone is generated during normal operation
of this copier. An unpleasant odor may, however, b e detected in
poorly ventilated rooms during extensive copier operations.
➜ For a comfortable operating environment, it is recommended that the
room be well ventilated.
Konica 7115/7118 2-3
2
Precautions
CAUTION
The area around the Fusing Unit is extremely hot.
➜ Do not touch any area other than those authorized in the manual to
reduce the risk of burns. Be especially careful not to touch parts
marked with warning labels, and their surrounding areas.
Transporting the Copier
Ifyouneedto transportthecopieroveralongdistance,consultyourTech.
Rep.
Care of Copier Supplies
Use the following precautions when handling the copier supplies (toner,
paper, etc.).
✚ S tore the supplies in a location that meets the following requirements:
Free from direct sunlight
Away from any heating apparatus
Not subjected to high humidity
Not extremely dusty
✚ P aper that has been removed from its wrapper but not loaded in the
copier should be stored in a sealed plastic bag in a cool, dark place.
- Use only toner that has been manufacturedspecificallyforthiscopier.
Never use other types of toner.
- Keep all supplies out of the reach of children.
CAUTION
Be careful not to spill toner inside the copier or get toner on your
clothes or hands.
➜ If your hands become soiled with toner, immediately wash them with
soap and water.
2-4 Konica 7115/7118
Precautions
2.3 Legal Restrictions on Copying
Certaintypes of documents must not be copied with the purpose or intent
to pass copies of such documents off as the originals.
The following is not a complete list, but is meant to be used as a guide to
responsible copying.
<Financial Instruments>
G Personal checks
G Travelers checks
G Money orders
G Certificates of deposit
G Bonds or other certificates of indebtedness
G Stockcertificates
<Legal Documents>
G Food stamps
G Postage stamps (canceled or uncanceled)
G Checks or drafts drawn by government agencies
G Internal revenue stamps (canceled or uncanceled)
G Passports
G Immigration papers
G Motor vehicle licenses and titles
G House and property titles and deeds
<General>
G Identification cards, badges, or insignias
G Copyrighted works without permission of the copyright owner
In addition, it is prohibited under any circumstances to copy domestic or
foreign currencies, or works of art, without permission of the copyright
owner.
When in doubt about the nature of a document,consultwith legal counsel.
2
Konica 7115/7118 2-5
2
Precautions
2-6 Konica 7115/7118
Before Making Copies
3 Before Making Copies
3.1 Available Features
The main copy settings available with this copier are listed below. For
details on their operation, refer to the pages indicated.
Copies
G 1-sided copies (p.6-1)
G 2in1 copies (p.6-1)
3
G 4in1 copies (p.6-1)
G Dual Page copies (p.6-2)
Konica 7115/7118 3-1
3
Before Making Copies
Zoom Ratio
G Reduced/Full Size/Enlarge (p.5-11)
Output
G Sort (p.6-6)
G Group (p.6-8)
✎
Note
The Output functions available are limited according to the options
equipped to the copier.
3-2 Konica 7115/7118
Before Making Copies
Applications
G Erase (p.6-10)
G Reverse Image (p.6-13)
G X/Y Zoom (p.5-14)
G Image Shift ( p.6-14)
3
Mixed Orig. Detection
G Mixed Originals (p.4-4)
✎
Note
The Mixed Orig. Detection function is available when the copier is
equipped with an Automatic Document Feeder (option).
Konica 7115/7118 3-3
3
3.2 Components and Their Functions
Copier
G Konica 7115/7118
Platen Cover CV-117 (option)
G Presses down on an original placed
on the Original Glass.
Standard on Konica 7115.
Automatic Document Feeder DF-217 (option)
G Automatically feeds originals one
page after another for scanning.
Before Making Copies
Paper Feed Unit PF-121 (option)
G Capableofholdingup to 250 sheets
of paper.
Shifting Unit IS-101 (option)
G Permitssortingorgrouping of copies according to the particularoutput
setting made.
Job Separator IT-102 (option)
G Performssortingand grouping of faxes, printedpages,andcopiesinto
the upper or lower bin.
3-4 Konica 7115/7118
Before Making Copies
Multiple Bypass MT-102 (option)
G Up to 50 sheets of Paper can be
loaded in the Bypass Tray.
Pedestal (option)
G Adjusts the height when a Paper
Feed Unit is mounted.
Fax unit for Konica 7115/7118 FK-117 (option)
G Permits fax transmission using this copier.
Printer Controller IP-413 (option)
G A built-in type printer controller that allows the copier to be used as a
printer with the copier connected to a personal computer.
Network Interface Card KN-305 (option)
G Allows the copier to be used as a network printer.
16MB Memory for Copier MU-409 (option)
32MB Memory for Copier MU-410 (option)
G Expands the memory capacity of the copier (16MB, 32MB), thereby
allowing image rotation and 2in1 copying to be performed.
3
Konica 7115/7118 3-5
3
3.3 Parts Names and Their Functions
Copier
1
Before Making Copies
2
3
8
7
6
5
4
9
10
11
* The above illustrations represent a copier mounted with the optional
Platen Cover.
3-6 Konica 7115/7118
Loading...