Konica Minolta 1216 User Manual
1216
User's Manual
Konica 1216 Copier
User’s Manual
As an ENERGY STAR
®
partner, Konica Business Technologies, Inc. has
determined that this product meets the ENERGY STAR guidelines for energy
efficiency.
Recycled paper is used for the inside pages of this book.
Konica 1216 User’s Manual
© 1998 by Konica Business Technologies, Inc.
Disclaimer
Konica Business Technologies, Inc. has made every effort to ensure that the
information in this manual is complete and accurate. However, constant efforts are
also being made to improve and update the product. Therefore, Konica Business
Technologies, Inc. shall not be liable for errors in this manual or for any consequential
damages resulting from the use of this manual. The information contained herein is
subject to change without notice.
FEDERAL OR STATE STATUTES MAY PROHIBIT THE COPYING OF CERTAIN
DOCUMENTS OR INFORMATION, RESULTING IN FINES OR IMPRISONMENT
FOR VIOLATOR.
User’s Manual Part Number
OP-01-1216
Web Site
http://www. konicabt. com
Correspondence
Konica welcomes your comments regarding the content of this manual. Mail all
correspondence regarding documentation to the following address:
Konica Business Technologies, Inc.
Digital Systems Solutions Group & New Product Development
500 Day Hill Road
Windsor, CT 06095
i
Table of Contents
Section 1: Introduction
To the User ........................................................................................ 1-2
Copier Highlights................................................................................ 1-3
Features......................................................................................... 1-3
Standard Equipment ...................................................................... 1-3
Optional Equipment ....................................................................... 1-3
Using this Manual .............................................................................. 1-4
Section 2: Safety Information
FCC Regulations................................................................................ 2-2
Canadian Department of Communications Regulations .................... 2-2
User Instructions ................................................................................ 2-3
Safety Alert Symbols ..................................................................... 2-3
Machine Safety Labels....................................................................... 2-4
Installation Requirements .................................................................. 2-6
Power Source Information ................................................................. 2-7
Machine Handling and Care .............................................................. 2-8
Routine Safety Check ...................................................................... 2-11
Section 3: Copier Information
External View ..................................................................................... 3-2
Internal View ...................................................................................... 3-4
Options............................................................................................... 3-5
Control Panel ..................................................................................... 3-6
Site Requirements ............................................................................. 3-8
Turning the Copier On ..................................................................... 3-10
Power Saver .................................................................................... 3-10
Auto Low Power........................................................................... 3-11
Manual Shut-Off........................................................................... 3-11
Auto Shut-Off ............................................................................... 3-11
Automatic Settings ........................................................................... 3-12
Initial Machine Settings................................................................ 3-12
Auto Reset ................................................................................... 3-12
Automatic Paper Selection (APS)................................................ 3-12
Automatic Exposure Selection (AES) .......................................... 3-13
Automatic Magnification Selection (AMS).................................... 3-13
Automatic Edge Delete ................................................................ 3-13
Latch ............................................................................................ 3-13
ii
Table of Contents
Section 4: Paper Specifications
Originals on Platen Glass .................................................................. 4-2
Originals on Automatic Document Feeder (ADF) .............................. 4-2
Copy Paper in Main Body Trays ........................................................ 4-2
Copy Paper in Drawer Base (DB-207A) ............................................ 4-2
Copy Paper in Drawer Base (DB-607) ............................................... 4-2
Copy Paper and Special Stock in Bypass.......................................... 4-3
Copy Paper in 10-Bin In-Bin Stapler Sorter (ST-104) ........................ 4-3
Copy Paper in 10-Bin Off-Line Stapler Sorter (ST-103)..................... 4-3
Paper Capacity/Size/Weight Compatibility Chart ............................... 4-4
Section 5: Basic Copying
Copying from the Platen Glass .......................................................... 5-2
Copying from the Document Feeder (ADF) ....................................... 5-3
Using the Bypass ............................................................................... 5-4
Copy Density...................................................................................... 5-5
AES................................................................................................ 5-5
Manual Density .............................................................................. 5-5
Copy Size........................................................................................... 5-6
Lens Modes ....................................................................................... 5-7
Automatic Magnification Selection (AMS)...................................... 5-7
Preset and User Preset Ratios ...................................................... 5-8
Programming a User Preset Ratio................................................. 5-9
Zoom Mode.................................................................................. 5-10
Special Ratio Table...................................................................... 5-11
Using the Sorter ............................................................................... 5-12
Specifications: 10-Bin In-Bin Stapler Sorter (ST-104) ................. 5-12
Specifications: 10-Bin Off-Line Stapler Sorter (ST-103) .............. 5-13
Non-Sort, Sort, and Group Modes for ST-104/103 .......................... 5-14
Staple-Sort Modes for ST-104 ......................................................... 5-15
Automatic In-Bin Stapling ............................................................ 5-15
Manual In-Bin Stapling................................................................. 5-15
Off-Line Stapling Option .............................................................. 5-16
Section 6: Duplex Copying
Manual Duplex ................................................................................... 6-2
1-Sided to 2-Sided Using the Bypass ............................................ 6-2
2-Sided to 2-Sided Using the Bypass ............................................ 6-3
iii
Table of Contents
Section 7: Special Copying
Shift/Reduce & Shift........................................................................... 7-2
Using the Platen Glass .................................................................. 7-2
Using the ADF ............................................................................... 7-3
Frame and Fold Erasure .................................................................... 7-4
Using Frame and Fold Erasure...................................................... 7-4
Setting Frame Erasure................................................................... 7-5
Setting Fold Erasure ...................................................................... 7-6
Book Copy ......................................................................................... 7-7
Mixed Original .................................................................................... 7-8
OHP Interleave .................................................................................. 7-9
Auto Copy ........................................................................................ 7-10
Section 8: Maintenance and Supplies
Service, Supplies, and Repairs.......................................................... 8-2
Daily Maintenance ............................................................................. 8-3
Cleaning the Platen Glass ............................................................. 8-3
Cleaning the Inner Surface of the Platen Cover ............................ 8-3
Cleaning the ADF Conveyance Belt Surface................................. 8-3
Cleaning the Corona Wire.................................................................. 8-4
Removing/Inserting Paper Trays ....................................................... 8-4
Loading Paper.................................................................................... 8-5
Service-Adjustable Tray (Tray 1, 2 and 4) ..................................... 8-5
LCT (Large Capacity Tray: Tray 3) ................................................ 8-6
User-Adjustable Tray (Option) ....................................................... 8-7
Adding Toner ..................................................................................... 8-8
Replacing the Staple Cartridge ........................................................ 8-10
In-Bin Stapler ............................................................................... 8-10
Off-Line Stapler............................................................................ 8-11
Installing the Off-Line Corner Stapling Adapter ............................... 8-12
Removing the Off-Line Corner Stapling Adapter ............................. 8-12
Preventive Maintenance .................................................................. 8-13
Reading the PM Count ................................................................ 8-13
Moving the Copier............................................................................ 8-14
iv
Table of Contents
Section 9: Troubleshooting
Opening and Closing the Copier........................................................ 9-2
User Codes ........................................................................................ 9-3
Mishandled Paper Codes................................................................... 9-4
Clearing Mishandled Paper................................................................ 9-5
Service Codes.................................................................................. 9-13
Reporting Service Codes............................................................. 9-13
Clearing a Wedged Staple ............................................................... 9-14
In-Bin Stapler (Code J75) ............................................................ 9-14
Off-Line Stapler............................................................................ 9-15
Troubleshooting Hints ...................................................................... 9-17
Glossary
Specifications
Introduction 1-1
Section 1: Introduction
To the User
Copier Highlights
Features
Standard Equipment
Optional Equipment
Using this Manual
1-2 Introduction
Introduction
To the User
Welcome to the Konica 1216 copier system. To ensure optimal
performance and safety, handle and operate the 1216 copier system as
recommended in this manual.
Copier Service and Repairs: If you require service or repairs, contact
your Konica dealer or service representative immediately. Do not
attempt to disassemble or repair the copier yourself. All repairs should
be performed by an authorized Konica service representative.
Supplies: Use only supplies recommended by Konica Business
Technologies, Inc. If you require special information regarding supply
items, please contact your Konica dealer or service representative.
Follow recommendations regarding compatibility, usage, storage, and
handling of all supplies.
NOTE: Record important telephone numbers using the form on p. 8-2.
Maintenance Agreement: The Konica 1216 copier system will give you
many years of trouble-free service. To ensure high quality copying
performance and to prevent premature wear of precision parts and
components, periodic cleaning and routine adjustments should be
scheduled.
Konica recommends that you contact your service center to discuss the
benefits of Konica’s Customer Service Maintenance Agreement and to
learn how a maintenance plan can be tailored to meet your individual
needs.
Introduction 1-3
Introduction
Copier Highlights
The Konica 1216 is a 16 copies-per-minute (cpm) desktop copier
available with either platen cover or automatic document feeder (ADF)
configuration. The Konica 1216 copier system offers the following
features, standard equipment and optional equipment:
Features:
16 CPM
Image Shift
Reduce & Shift
Frame/Fold Erasure
Book Copy
OHP Interleave
Standard Equipment:
50-sheet Stack Bypass
Main Body with Two Tray Ports
User’s Manual
Optional Equipment:
Platen Cover
Automatic Document
Feeder (DF-204)
Drawer Base with PFU (DB-207A)
Drawer Base with LCT and PFU (DB- 607)
Stand
10-Bin In-Bin Stapler Sorter (ST-104)
10-Bin Off-Line Stapler Sorter (ST-103)
Off-Line Stapler
Service-Adjustable Paper
Tray (8.5"x11"R)
User-Adjustable Paper Tray
Key Counter
Auto Reset
Auto Shut-Off
Power Saver
Automatic Paper Selection (APS)
Automatic Exposure Selection (AES)
Automatic Magnification Selection (AMS)
1-4 Introduction
Introduction
Using this Manual
The Konica 1216 User’s Manual includes nine sections of information
relating to the copier and copying functions, plus a glossary and
specifications. For easy reference, each section begins with a list of
subjects covered.
To ensure the best performance and most effective use of this copier,
read this manual before using the copier, and keep it located with the
machine for quick reference and the convenience of all users.
Section 1: Introduction presents an overall introduction to the copier,
including a list of its features.
Section 2: Safety Information provided safety precautions for copier
set-up and operation.
Section 3: Copier Information identifies copier parts, accessories, and
features, including the control panel and automatic settings.
Section 4: Paper Specifications lists paper capacities, weights, and
sizes for all copying modes and accessories.
Section 5: Basic Copying describes simple copying procedures,
including using the bypass and using the optional sorters.
Section 6: Duplex Copying describes manual copying procedures for
1s2 and 2s2 copying, using the ADF or platen glass with the bypass tray.
Section 7: Special Copying provides instruction for advanced copying
applications such as Image Shift, Reduce & Shift, Frame/Fold Erasure,
Book Copy, Mixed Original, OHP Interleave, and Auto Copy.
Section 8: Maintenance and Supplies includes information on copier
care and maintenance. This section describes how to replace supplies
and periodically clean machine components.
Section 9: Troubleshooting provides troubleshooting information to
help you solve problems relating to copy quality, mishandled paper,
error messages, and error codes.
Safety Information 2-1
Section 2: Safety Information
FCC Regulations
Canadian Department of Communications Regulations
User Instructions
Safety Alert Symbols
Machine Safety Labels
Installation Requirements
Power Source Information
Machine Handling and Care
Routine Safety Check
2-2 Safety Information
Safety Information
FCC Regulations
NOTICE: The Konica 1216 copier generates, uses, and can radiate
radio frequency energy. If it is not installed and used in accordance
with the instruction manual, interference with radio communications
may result. This equipment has been tested and found to comply with
the limits for a class A computing device, pursuant to Subpart B, Part
15, of FCC rules, which are designed to provide reasonable protection
against interference from such equipment when it is operating in a
commercial environment.
Users operating this equipment in a residential area are likely to cause
interference, in which case they may be required to correct the
interference at their own expense.
Canadian Department of Communications Regulations
Le présent appareil n’émet pas de bruits radioélectriques dépassant
les limites applicables aux de Classe A prescrites dans le règlement
sur la brouillage radioélectrique édicté par Le Ministère des
Communications du Canada.
This equipment does not exceed the Class A limits for radio noise
emissions as set out in the radio interference regulations of the
Canadian Department of Communications.
Safety Information 2-3
Safety Information
User Instructions
The following pages contain important safety information. To avoid risk
of fire, electric shock, serious personal injury, and/or poor machine
performance, read all safety information before operating the copier
and heed all safety precautions. If you have any questions or concerns
about safety matters, contact a Konica service representative.
Keep this manual permanently located with the copier, and in good,
legible condition. The manual should be readily available to all users.
Safety Alert Symbols
Safety Alert Symbols are attached to some inside areas of the machine
and are also used in this manual to alert you to potentially hazardous
situations or conditions. The following are typical examples of safety
alert indicators used on product labeling.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will
result in death of serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
NOTE: The above safety alert information is presented for better understanding
of hazardous situations. Since this product has only the potential for hazardous
situations classified under CAUTION, only CAUTION indications will be found
on the copier and in this manual.
2-4 Safety Information
Safety Information
Machine Safety Labels
Machine safety labels are attached to some inside areas of the copier.
The purpose of these safety labels is to alert you to imminent or
potentially hazardous situations or conditions.
You may be injured if you touch any machine area that you are
advised by any caution label or caution indication to avoid.
Do not remove caution labels. If any caution label is removed, or if any
caution indicator is illegible due to soilage, contact your Konica service
representative.
The copier has caution labels at the locations shown right. When
removing mishandled paper, adding toner, or stapling, exercise care in
order to avoid any accidents such as burns, electric shock, or other injury.
Ne pas insérer les doigts autour de la tête d’agrafes pour éviter toute blessure.
To avoid injury, do not insert your fingers around staple unit.
CAUTION
CAUTION
PRECAUCION
HIGH TEMPERATURE WILL CAUSE BURNS. TAKE CARE WHEN REMOVING JAM.
HAUTE TEMPERATURE CAUSE DES BRULURES. RETIRER BLOCAGE AVEC SOIN.
ALTA TEMPERATURA CAUSA QUEMADURAS. CUIDADO AL REMOVER ATOROS.
HIGH VOLTAGE CAUTION.
ATTENTION HAUTE TENTION.
PRECAUCION ALTO VOLTAJE.
CAUTION
CAUTION
PRECAUCION
HIGH TEMPERATURE WILL CAUSE BURNS.
TAKE CARE WHEN REMOVING JAM.
HAUTE TEMPERATURE CAUSE DES BRULURES.
RETIRER BLOCAGE AVEC SOIN.
ALTA TEMPERATURA CAUSA QUEMADURAS.
CUIDADO AL REMOVER ATOROS.
Label 1
Label 2
Label 3
Label 5
Label 4
Safety Information 2-5
Safety Information
Machine Safety Labels (continued)
Copier with ST-104
All models
Label 5
Label 2
Label 1
Label 3
Label 4
Copier with Stand, DB-207A or DB-607
2-6 Safety Information
Safety Information
Installation Requirements
CAUTION
FIRE PREVENTION
❐ Install copier away from flammable materials, curtains and volatile
combustibles.
TEMPERATURE AND HUMIDITY
❐ Install copier away from direct sunlight, heat sources (stoves,
heaters), cold temperatures (air conditioners), and dampness.
❐ Do not install or operate copier outdoors near a lake, pond, river,
etc. Do not allow copier to come in contact with splashes of rain,
water, or any liquid.
❐ Avoid any environment that is outside 50°~91°F (10°~33°C) with
10~80% relative humidity.
VENTILATION
❐ Install copier in a well-ventilated area to maintain a comfortable
working environment. When in use, the copier generates ozone in
amounts too small to be hazardous to the human body. However,
if the machine is used in a poorly ventilated area or if many copies
are made, an odor may be detected.
❐ Install copier in an area free from dust, ammonia gas or fumes
from printing or cleaning solutions, etc. Exposure of the copier to
these materials may also cause poor image quality.
INSTALLATION SPACE
❐ Install copier in an area with adequate space for performing copier
operations, replacing supply items, and conducting regular
maintenance.
❐ Install copier on a flat, sturdy surface, free from strong vibrations.
Be sure the surface is able to support the additional weight of
paper and supplies.
Safety Information 2-7
Safety Information
Power Source Information
CAUTION
PLUG SOCKET
❐ A plug socket is limited in capacity. Use an exclusive power source
for the copier. The total power consumption of the copier, plus all
possible options, must not exceed the capacity of the main power
supply. For information about power requirements and power
consumption related to the copier, contact your Konica service
representative.
❐ Firmly insert the copier plug into the outlet. If the inserted plug is
loose in the socket, disconnect the plug and consult an electrician
for repair.
POWER CORD
❐ Do not bend, crush, wind, or roll up the power cord. If your copier
power cord is bent or damaged in any way, contact your Konica
service representative immediately. Do not attempt to repair it
yourself, and do not continue to operate the copier. A damaged
power cord may result in overheating, a short circuit, or fire.
EXTENSION CORDS (LEADS)
❐ Do not use an extension cord without first consulting with an
electrician and a Konica service representative.
ADAPTERS AND MULTIPLE LOADS
❐ Do not use adapters or connectors with the main power cord.
❐ Never connect plural loads or a branched socket to one socket
outlet. Otherwise, an accident may occur as a result of overheating
or fire.
2-8 Safety Information
Safety Information
Machine Handling and Care
CAUTION
INTERNAL MACHINE COMPONENTS
❐ Never touch internal high voltage, high temperature or magnetism
area indicated with caution labels.
❐ Never touch the drum surface or any internal machine part
indicated by a do not touch (or pull) statement.
❐ Never touch the inside of the copier for any purpose other than
removing mishandled paper or adding toner.
ABNORMAL CONDITIONS
❐ If any abnormal sound, odor, or smoke generates from the copier,
immediately stop using the machine, turn off the main power
switch, disconnect the plug and contact your service
representative.
❐ If a circuit breaker is tripped or if a fuse blows, stop using the
copier and contact an electrician. If information is needed
regarding the power source or power consumption of the copier,
contact your Konica service representative.
FIRE PREVENTION
❐ Do not use any volatile combustibles, e.g., paint thinner, alcohol,
etc., on or near the machine.
MACHINE MODIFICATIONS
❐ Do not modify the machine in any way or remove any part.
❐ Never remove any covers or guards that are fastened with screws.
There are no user-serviceable areas within these covers.
❐ Never attempt any maintenance function that is not specifically
described in this manual.
Safety Information 2-9
Safety Information
Machine Handling and Care (continued)
CAUTION
SERVICE CODES
❐ If a service code (F code) is indicated on the machine control
panel, make a note of the code, turn the machine off, disconnect
the power cord from the outlet, and report the F code to your
service representative.
MACHINE CARE
❐ Do not drop paper clips, staples, or other small metallic objects
into the copier.
❐ Do not spill water or any other liquid into the copier.
❐ Do not use the copier surface to support vases, books, etc. These
items will interfere with the work space and may cause damage to
the copier or to originals.
TONER
❐ Keep toner away from children. Do not inhale toner or allow it to
come in contact with eyes. If inhalation or eye contact occurs,
consult a physician immediately. For additional toner safety
information, refer to the appropriate Material Safety Data Sheet
(MSDS).
SUPPLIES AND CLEANING MATERIALS
❐ Use only paper and supplies recommended by Konica Business
Technologies, Inc.
❐ Never use supplies or cleaning materials for purposes other than
that for which they were intended. Keep all materials out of the
reach of children.
❐ Follow all warnings and instruction labels attached to or
accompanying the copier.
2-10 Safety Information
Safety Information
Machine Handling and Care (continued)
CAUTION
ST-104 10-BIN IN-BIN STAPLER SORTER HANDLING
❐ To avoid injury when using the In-Bin Stapler Sorter, do not insert
your fingers around staple unit.
SORTER TOP BIN CAPACITY
❐ When using the sorter, the maximum capacity of the top bin is 100
sheets. If print quantity exceeds 100, remove copies before the
limit is exceeded during continuous copying. Otherwise, an
accident or mishandled paper may occur.
POWER SAVER
❐ Turn machine power off when not copying for long periods of time.
MACHINE RELOCATION/DISPOSAL
❐ Before moving the copier to another location, contact your Konica
service representative.
❐ Do not dispose of the copier yourself. Contact your Konica service
representative.
Safety Information 2-11
Safety Information
Routine Safety Check
To ensure safety when operating this copier, perform a periodic safety
check on the copier and electrical connections by referring to the
following check list. Any special concerns should be immediately
brought to the attention of your Konica service representative.
Check for:
❐ power cord and plug for abnormal heat
❐ power cord and plug for any damage, fraying, and/or creasing
❐ power plug for loose connection
❐ power plug for dust
❐ ground wire to ensure correct connection
Special Concerns
Contact your Konica service representative if you have any questions
or concerns about:
❐ Safety
❐ Signs of overheating
❐ Copier damage
❐ Damage to the electrical connection
❐ Abnormal copier operation
❐ Supplies
Copier Information 3-1
Section 3: Copier Information
External View
Internal View
Options
Control Panel
Site Requirements
Turning the Copier On
Power Saver
Auto Low Power
Manual Shut-Off
Auto Shut-Off
Automatic Settings
Initial Machine Settings
Auto Reset
Automatic Paper Selection (APS)
Automatic Exposure Selection (AES)
Automatic Magnification Selection (AMS)
Automatic Edge Delete
Latch
3-2 Copier Information
Copier Information
External View
10-BIN OFF-LINE
STAPLER SORTER
ST-103 (option)
DRAWER BASE
DB-607 (option)
DRAWER BASE
DB-207A (option)
KONICA 1216
COPIER MAIN BODY
AUTOMATIC
DOCUMENT FEEDER
DF-204 (option)
10-BIN IN-BIN
STAPLER SORTER
ST-104 (option)
1
3
2
4
5
6
7
9
10
11
15
16
17
17
18
18
19
8
21
22
20
24
25
26
23
13
14
12
Copier Information 3-3
Copier Information
External View (continued)
KONICA 1216 COPIER MAIN BODY
1 MAIN POWER SWITCH
2 CONTROL PANEL
3 PLATEN COVER
4 KEY COUNTER (option)
5 50-SHEET STACK BYPASS
6 TOTAL COUNTER
7 SIDE COVER (main body)
8 PAPER TRAY (main body)
9 COPIER FRONT DOOR
10 FRONT DOOR RELEASE BUTTONS
(both sides of front door)
11 PAPER EXIT TRAY
DOCUMENT FEEDER (DF-204) (option)
12 ADF TRAY
13 ADF TRAY EXTENSION
14 ADF PAPER GUIDES
15 ORIGINAL EXIT TRAY
16 ADF PAPER ACCESS
DRAWER BASE (DB-607) (option)
17 SIDE COVER (drawer base)
18 DRAWER BASE PAPER TRAY
19 LARGE CAPACITY TRAY
DRAWER BASE (DB-207A) (option)
17 SIDE COVER (drawer base)
18 DRAWER BASE PAPER TRAY
10-BIN IN-BIN STAPLER SORTER (ST-104) (option)
20 SORTER BINS
21 SORTER COVER
22 MANUAL STAPLE BUTTON
10-BIN OFF-LINE STAPLER SORTER (ST-103) (option)
23 SORTER BINS
24 SORTER RELEASE LEVER
25 STAPLER COVER
26 OFF-LINE STAPLER (option)
NOTE: See more options on p. 3-5.
3-4 Copier Information
Copier Information
Internal View
1 UPPER MAIN BODY
2 TONER BOX COVER
3 TONER BOX
4 CORONA WIRE CLEANING KNOB
5 UPPER UNIT RELEASE LEVER
6 DRUM UNIT
7 FIXING UNIT
8 TOTAL COUNTER
1
2
3
4
5
6
7
8
CAUTION
The main body contains internal high voltage and high
temperature areas. Never touch areas indicated by caution labels.
Copier Information 3-5
Copier Information
Options
Stand
Service-Adjustable Tray
User-Adjustable Tray
Off-Line
Stapler
10-Bin Off-Line
Stapler Sorter
(ST-103)
10-Bin In-Bin
Stapler Sorter
(ST-104)
Automatic Document Feeder
(DF-204)
Konica 1216
Main body
Key Counter
Drawer Base (DB-207A) Drawer Base (DB-607)
3-6 Copier Information
Copier Information
Control Panel
1 COPIER DIAGRAM represents all areas of the copier with illuminated displays
to indicate mishandled paper locations and empty paper trays.
2 RELOAD ORIGINALS indicates the number of originals to reload in the
document feeder after mishandled paper occurs when copying from the ADF.
3 BYPASS INDICATOR flashes when the bypass tray is open, and lights steady
when tray is open and paper is placed in it.
4 PAPER TRAY INDICATORS light the paper source selected and flash when a
paper tray is empty.
5 ADD PAPER lights when a paper tray is empty.
6 CHECK PAPER PATH INDICATOR flashes when a paper tray is empty.
7 ADD TONER lights when toner supply is low.
8 CALL FOR PM lights when preventive maintenance is approaching, and
flashes when it is due.
9 GROUP lights to indicate Group mode is selected.
10 STAPLE lights to indicate Staple-Sort mode is selected when the In-Bin
Stapler Sorter (ST-104) is installed.
11 SORT lights to indicate Sort mode is selected.
12 SORTER button selects Staple-Sort, Group, Sort, and Non-Sort modes. Non-
Sort functions when light is off.
13 SHIFT/REDUCE & SHIFT creates a margin and reduces the image to prevent
image loss.
14 ERASURE (Fold/Frame) erases the center strip and/or border image.
15 MIXED ORIGINAL copies 8.5"x11" with 11"x17" originals or 8.5"x14" with
8.5"x11"R originals from the ADF.
16 BOOK COPY produces two 8.5”x11” copies (dual pages) from an opened book
or large original sheet.
17 OHP INTERLEAVE inserts an OHP transparency copy with each blank plain
paper.
RELOAD ORIGINALS
MAGNIFICATIONCOPY DENSITY
USER PRESETDARKER
NORMAL
LIGHTER
FOLD
ERASURE
FRAME
REDUCE
& SHIFT
CHECK
PAPER
PATH
SHIFT
ORIGINAL
MIXED
BOOK
COPY
AUTO
COPY
STAPLE
GROUP
SORT
SORTER
MESSAGE CENTER
ADD
PAPER
ADD
TONER
CALL
FOR PM
9
1
2
3
4
6
7
8
5
OHP
INTERLEAVE
12356
4781112161718
91013 14 15 19 21
20 22
Copier Information 3-7
Copier Information
Control Panel (continued)
18 AUTO COPY automatically activates copying each time the Document Feeder
is closed.
19 COPY DENSITY INDICATORS light the density level selected.
20 COPY DENSITY manually overrides AES in seven levels, from normal to
lighter or darker.
21 USER PRESET INDICATOR lights when the user set lens mode is selected.
22 MAGNIFICATION [▼]/[▲] arrows increase or decrease the current ratio.
23 ZOOM INDICATOR lights when the Zoom mode is selected.
24 RATIO WINDOW displays the magnification ratio in use and machine codes.
25 PRESET INDICATOR lights when the Preset mode is selected.
26 LENS MODE selects Preset or Zoom modes for manual ratio selection.
27 COPY SIZE INDICATORS light to indicate the copy size selected.
28 COPY SIZE overrides APS for manual copy size selection.
29 AUTO INDICATORS light when the AUTO button is pressed to indicate APS,
AES, ADF and SORTER are activated; go out when copy conditions are set
manually.
30 AUTO restores the initial machine settings and clears copy selections.
31 KEYPAD is used to enter print quantity and Frame/Fold Erasure values.
32 [P] KEY is sued to access all programming functions.
33 [O] RECALL recalls print quantity selected while copying is in progress.
34 STOP/CLEAR stops continuous copying and allows reset of print quantity.
35 PRINT QUANTITY WINDOW displays print quantity when selected and
cumulative quantity while copying is in progress.
36 POWER SAVER activates an energy saving mode when the copier will not be
used for an extended period of time.
37 START PRINT indicates
wait
when light is amber and
ready
when light is bluegreen; activates copying when pressed while copier is in the ready-to-copy
state.
START PRINT
PRINT QUANTITY
POWER SAVER
STOP/CLEAR
RECALL
AUTO
COPY SIZE
SPECIAL
8
2
1
11
8
2
1
11R
5
2
1
8
2
1
8
2
1
14
11
17
LENS MODE
ZOOM
PRESET
123
456
789
P0
27 29 3123 24
25 26 28
30 32 33 34
35 36
37
3-8 Copier Information
19.7
(500)
24.4
(620)
59.7
(1520)
15.7
(400)
37.8
(960)
57.4
(1460)
31.5
(800)
62.2
(1579)
22.8
(579)
7.9
(200)
42.3
(1075)
Konica 1216 with Stand
Konica 1216 with DF-204, DB-207A and ST-103
Unit: inches (mm)
Unit: inches (mm)
62.0
(1575)
31.5
(800)
62.2
(1579)
23.0
(584)
7.9
(200)
24.4
(620)
15.7
(400)
63.4
(1610)
23.2
(590)
19.7(500)
19.7(500)
Copier Information
Site Requirements
Loading...