konica DIGITAL REVIO KD-300Z user Manual

GB/

Thank you for purchasing this Konica product. Digital Revio KD-300Z is a digital camera equipped with a 3.34 megapixel CCD for high quality digital photography. Before using the camera, please read this User’s Manual carefully and follow its instructions to assure proper use.

Wir danken Ihnen für das Vertrauen, das Sie Konica mit dem Kauf dieses Produkts bewiesen haben. Bei der Digital Revio KD-300Z handelt es sich um eine Digitalkamera, deren CCD-Element mit 3,34 Mio. Pixeln arbeitet, so dass Digitalaufnahmen von höchster Qualität erzielt werden. Bitte lesen Sie diese Anleitung vor Inbetriebnahme der Kamera aufmerksam durch, damit Sie alle Funktionen optimal nutzen können, und befolgen Sie alle Anweisungen, um einen fehlerfreien Betrieb zu gewährleisten.

Contents

Please purchase “Secure Digital (SD) Memory Cards” or “Multi-Media Cards*” (MMC) for use with this camera. These cards are referred to in these User’s Instructions as “Memory Cards.”

Names of Parts.......................... 4

* MultiMedia Card is a registered trademark of Infineon Technologies AG

(Germany), licensed to MMCA (MultiMediaCard Association).

Basic Preparations

Camera Basics

Camera Functions

Image Playback Basics

Advanced Image Playback and Delete Functions

Camera Setup Options

Loading and Recharging the

Battery Pack.............................. 9

Using the LCD Monitor when

Shooting .................................. 13

Selecting Flash Mode ............. 22

Macro and Landscape

Photography............................ 24

Using the Self-timer ................ 26

Setting Image Quality.............. 27

Exposure Compensation......... 29

Using Color Mode for B&W

and Sepia Images ................... 30

Displaying Images on the LCD

Monitor .................................... 42

“Thumbnail” Picture Review in

Forward/Reverse Direction ..... 45

Closeup Image Playback ........ 45

Displaying Exposure

Information .............................. 46

Formatting Memory Cards ........

Turning the Electronic Tone

ON/OFF ................................... 59

Setting Auto Power-Off........... 60

Selecting the Automatic

Loading and Removing Memory

Cards ....................................... 10

Recording Moving Images ...... 17

White Balance ......................... 31

Aperture-Priority

Photography............................ 34

Using Manual Focus ............... 35

Long Exposure Mode.............. 36

Increasing Exposure Sensitivity

to 2x, 4x................................... 38

Playing Movies ........................ 43

Multiple Image Display

(Index Display) ......................... 47

Erasure Prevention .................. 48

Erasing Individual Images ....... 49

Erasing All Images................... 50

Focus Mode ............................. 62

Mode Lock ON/OFF................ 63

Digital Zoom ON/OFF ............. 65

Selecting the Display Language .....

Selecting the Video

Setting the Date ...................... 12

Using the Optical

Viewfinder................................ 18

Selecting the Metering

Mode........................................ 39

Other Functions....................... 41

Rotating Images ...................... 52

Automatic Playback ................ 53

Digital Print Order Format

(DPOF) Setting......................... 54

Output Mode ........................... 67

Creating a New Folder on the

Memory Card........................... 68

Returning Settings to their

Default Values.......................... 70

Transferring Images to Other Devices

Other Information

Computer................................. 73

LCD Monitor Operations ......... 76

Caution and Warning Symbols ..

Sending Images to a Printer ..... 74Transferring Images to a

Handling Precautions.............. 77

Troubleshooting ....................... 83

Specifications.......................... 87

Names of Parts

“ ” Macro/ Landscape mode button

(page 24)

Use this button to select Macro or Landscape mode.

“ ” Flash mode button

(page 22)

Use this button to select flash mode.

“DISPLAY” button

In the recording mode ( ), use this button to turn the LCD monitor ON/OFF.

“POWER” button

Use to turn camera power ON/OFF.

Shutter release button

Mode select lever

Use this lever to switch between record, playback, and setup modes.

“@” “#” “%” “ﬁ” buttons

Use to select items on each menu, and to select forward/ reverse playback modes.

“W” “T” Zoom buttons

Use to control the lens’s zoom setting (wide-angle to telephoto) when recording, and to enlarge images during playback.

“ ” button

Use this button to adjust LCD screen brightness and to set items on menus.

“MENU” button

Use this button to display or turn off the menus in recording or playback mode.

Caution LED (red)

This LED is used to signal the charge status of the lithium ion battery, the charging status of the electronic flash, and the camera shake warning.

During Recording

Other

LCD monitor

Functions as viewfinder during recording, and displays images and menu information during the playback and setup modes.

Self-timer LED (red)

This LED flashes when using selftimer photography, and it lights steadily when recording moving images or playback and when using the setup mode.

Flash charging

Camera shake warning

During battery charging

Battery charging error

Flashes (about 2 times/sec)

Flashes (about 4 times/sec)

Lights steadily

Flashes

Standby LED (green)

This LED is used to indicate the infocus status and the completion of battery recharging.

Card access LED (orange)

This LED flashes to indicate that the camera is currently writing data to the memory card. ¶ Never open need to standardize

to cover or door, or remove the memory card when this LED is flashing.

Optical viewfinder

Light sensor

Lens and lens cover

Connector cover

Video output connector (page 16) Power supply input socket (page 9)

Battery pack compartment and cover

(page 9)

Flash

(page 18)

Strap lug (page 11)

Memory card door release

Memory card door

(page 10)

Tripod socket

Macro/Landscape mode (page 24) Flash mode (page 22) Metering mode (page 39) Focus mark (lights when focus is set)

Color mode (page 30) / White balance mode (page 31)

Image quality (page 27) Number of images recordable

Auto-Exposure mode (page 34) Sensitivity (page 38) Long time exposure (page 36) /

Exposure compensation value (page 29)

Digital zoom (page 15) Focusing scale (displayed only

during manual focus) (page 35)

Menu display during recording Data (page 12): Automatically displayed

for 3 seconds after power is turned ON. Battery indicator (page 9): Indicates

remaining battery capacity Self-timer (page 26): Displays the

number of seconds remaining until the self-timer releases the shutter.

Loading and Recharging the Battery Pack

Basic

Preparations

Open the battery compartment cover and insert the supplied battery pack.

¶ Be sure to insert the battery pack in

the correct direction; the camera will not operate if the battery pack is loaded incorrectly.

Connect the AC adapter to the camera and plug it into a household outlet to begin recharging.

Standby LED Caution LED

Full recharging requires approximately 5 hours.

During recharging, the caution LED will light steadily. When recharging is completed, the caution LED will go out and the standby LED will light.

Charge the battery pack in accordance with the battery indicator status shown on the LCD monitor.

Low

warning

Charge

required

Loading and Removing Memory Cards

Slide the memory card door release to open the card door.

Insert the memory card.

¶ Slide in the card until it stops with a

secure click.

¶ Be careful to insert the memory card in

the correct direction.

Close the memory card door.

Slide the memory card door release to open the card door, and pull out the memory card.

Write Protect Switch

(SD Memory Cards only)

SD Memory Cards are provided with a write-protect switch. When this switch is moved downward, further recording on the card is disabled, to

LOCK

protect any images and data already on the card. When in this status, no further images can be recorded on the card, and images already on the card cannot be erased.

The LCD monitor will display “WRITE PROTECT”.

Attach the supplied hand strap as shown.

Press the edge of the memory card in slightly before pulling out.

1110

Setting the Date

Follow these instructions to set the date, time, and calendar display mode:

Set the mode select lever to “ ”.

Press the “#” button.

The monitor will show the date/time setting display. Press the “@” and “#” buttons to change the setting item, and the “%” and “ﬁ” buttons to change the numerical values.

To cancel the setting operation: Press the “MENU” button; the setting contents will revert to those before the setting operation was begun.

To confirm the new setting data, press the “

” button.

This completes the operation, and the LCD monitor will return to the menu screen.

Camera

Basics

Using the LCD Monitor when Shooting

Use the LCD monitor to compose your pictures when particularly accurate composition is needed. The image recorded will be the same as that seen through the monitor .

1. Set the mode select lever to ” , then press the power

“ ON/OFF button to turn on camera’s power.

An electronic beep will be heard for several seconds, followed by the appearance of the LCD monitor.

Automatically displayed for 3 seconds, then turns off.

2. Hold the camera steadily with both hands as shown to avoid camera shake.

3. Compose your picture while watching through the LCD monitor.

Press the zoom buttons to range between telephoto and wideangle lens settings, thus enlarging or reducing the size of your subject. Press the “T” button to enlarge the subject, and the “W” button to reduce the size of the subject.

The magnification ratio is displayed on the screen.

4. Press the shutter release button to take the picture

1 Lightly depress the shutter

release button halfway (see page 16) to begin focusing; the focus mark will light and the electronic beep will be heard when focus is locked.

“Beep,

beep”

Blurry pictures are most often caused by camera shake. Find the position and stance that is most comfortable for you and allows you to hold the camera steadily. ¶ Rest the right index finger lightly

on the shutter release.

¶ Take care that the flash and lens

are not covered by your hand or fingers.

¶ Press the shutter release button

gently, without grasping the camera too tightly,

¶ Use the left hand to support the

camera firmly.

¶ Hold your elbows close to your

body and hold the camera steadily.

WT WT

Press the “T” button until the zoom function reaches the maximum telephoto setting; release your finger slightly, then press the button again. The digital zoom will further enlarge the subject in three steps (1.3x, 1.6x and 2x the maximum optical zoom value).

¶ Since electronic circuitry is used

to increase the magnification ratio, the results cannot be seen in the optical viewfinder. Always be sure the LCD monitor is turned ON when using the digital zoom function.

¶ Digital zoom cannot be used

when the LCD monitor is not turned ON.

¶ Digital zoom also cannot be

used when image quality is set to [T] or [ ]. If pictures are taken with digital zoom when image quality is set to [S] or [F], actual image quality will be equivalent to [N].

2 Press down further on the

shutter release button to take the picture; recording of the image begins when the electronic beep sound.

“Beep”

The LCD monitor will become momentarily

recorded image will be displayed.

dark, then the

3 The caution LED and card

access LED will flash while the camera is writing image data to the memory card.

Card access LED

Caution LED

1514

Recording Moving Images

¶ Wait until the caution LED has

stopped flashing before taking your next photograph .

¶ When the camera is in the “ ”

mode, setting the auto PowerSave function allows the camera to automatically enter the auto power-off (“power-save”) mode if left inactive for a set period of time. From this “sleep” state, the camera can be restored to its normal shooting condition by depressing the shutter button halfway, or by pressing one of the other function buttons. (For details, see page 60).

¶ Never open the memory card

door or remove a memory card while the card access LED is flashing, since the memory card may be damaged and data lost.

When the shutter release button is pressed down lightly, it will stops part way in its travel. In this semidepressed position, the camera automatically sets focus and exposure. When the shutter release button is pressed further down, the shutter is released and the image is recorded.

Not pressed

The camera can be connected to a television monitor to allow use of the screen as a large viewfinder.

When connected to a television monitor, the camera’s own built-in LCD monitor turns off, and the subject is displayed instead on the television screen. ¶ The camera’s built-in LCD

monitor turns off whenever a video cable is connected to the camera.

¶ Use a standard video cable to

connect the camera to the television.

This function allows you to record up to 15 seconds of simple movie images. The monitor display during movie recording is shown below:

1 Press the “MENU” button.

2 Select [ ], then press the

” button to set for movie

“ recording [

3 Press the shutter release

button to begin recording; fifteen seconds later the recording will end automatically.

This number indicates the remaining number of movies that can be

(each movie represents a maximum of 15 seconds of recording time).

¶ To stop recording before the 15

seconds has elapsed, press the shutter release button again.

recorded

<NOTE>

¶ The optical zoom can be used,

but the digital zoom (page 15) does not function during movie recording.

¶ To view movies on a computer,

installation of QuickTime 4.1 or later version is required.

Half-pressed

Fully depressed

1716

Using the Optical Viewfinder

Turning the LCD monitor off will help conserve battery power.

Turning LCD monitor OFF (page 76)

1. Set the mode select lever to ”, then press the

“ “POWER” button to turn power ON.

2. Press the “DISPLAY” button to

turn off the LCD monitor.

3. Hold the camera steadily as

shown to prevent camera shake.

Using the optical viewfinder to compose your picture.

¶ See <Hints for Holding the Camera

Steady> on page 14.

4. Look through the optical viewfinder while composing your image.

Press the “T” button to enlarge the subject, and the “W” button to reduce the size of the subject.

WT WT

When using the optical viewfinder, take note of the distance to your subject. As distance to the subject decreases, parallax (the difference between what you see in the viewfinder and the actual image recorded through the lens) increases. When accurate subject composition is required, use the LCD monitor to take your pictures.

¶ Parallax: see page 25.

5. Press the shutter release button to take the picture.

1 Lightly depress the shutter

button halfway to begin focusing; the focus mark will light and the electronic beep will be heard when focus is locked.

“Beep,

beep”

2 Press down further on the

shutter release button to take the picture; recording of the image begins when the electronic beep sound.

“Beep”

3 The caution LED and card

access LED will light while the camera is writing image data to the memory card.

Caution LED

Card access LED

¶ Your next picture can be taken

when the caution LED stops flashing.

1918

MEMO

Camera

Functions

This section introduces various functions available during image recording. Use them to enhance the range of your camera work.

When shooting with the LCD monitor turned OFF:

Note that the LCD monitor must be turned ON to set functions or to confirm previous settings.

Selecting Flash Mode

A variety of flash modes are available for different conditions.

About 90 cm

Camera

Usable flash range

About 2 meters

When sensitivity is normal

About 2.5 meters

Zoom set at wide

Zoom set at telephoto

When the “ ” button is pressed, the display changes as follows:

[

] Auto flash

mode (default):

[

] Red-eye reduction

auto-flash mode:

[ ] Fill-in flash mode:

[ ] Flash-off mode:

The camera automatically determines lighting conditions and switches between flash and available-light exposure as needed.

The flash fires twice to help reduce the “red-eye” phenomenon*.

In this mode, the flash fires regardless of surrounding light conditions. This mode provides fill-flash when shooting in a backlight environment or under strong sunlight when shadows are cast on the main subject.

In this mode the flash does not fire. This mode is effective when shooting an evening sunset or to preserve indoor mood.

1 Press the “ ” button to select

the desired flash mode.

Display appearance when the “red-eye reduction” mode is selected.

2 Press the shutter release

button to take the picture.

<NOTE>

¶ If the caution LED flashes when

the shutter release button is depressed halfway, it indicates that a slow shutter speed will be selected (low light conditions); in this case, use of a tripod is recommended to prevent camera shake.

¶ If the caution LED flashes when

the shutter release button is depressed halfway, it indicates that a slow shutter speed will be selected (low light conditions); in this case, use of a tripod is recommended to prevent camera shake.

* “Red-eye” Phenomenon: This phenomenon may occur when using flash to

photograph persons or pets under dark conditions. In some cases, the flash reflects against the retinas of the subject’s eyes, causing the pupils to appear red in the photograph.

2322

Macro and Landscape Photography

Use the macro and landscape shooting modes when photographing extremely close and distant subjects.

About 6 cm (zoom set at wide)

About 90 cm

Camera

Macro range Normal photography

Landscape range

Each time the “ ” button is pressed, the mode changes alternately as follows:

[No display] Normal mode

[

] Macro mode

] Landscape mode

Sharp images are produced when shooting subjects between 6 cm and 90 cm (at wideangle setting) from the camera.

Sharp images are produced of landscapes and other distant subjects.

1 Press the “ ” button

and select the desired mode.

Display appearance when the macro mode is selected.

2 Press the shutter release

button to take the picture.

When shooting in the macro mode, pressing the “ will permit macro flash photography.

Take care, however, since very close subjects may receive excessive exposure. In this case, use the exposure compensation function to compensate the exposure.

” button

<NOTE>

When shooting with the optical viewfinder (LCD monitor turned OFF), if the macro mode [ ] is selected, the LCD monitor will automatically turn ON when the shutter release button is depressed halfway.

Since parallax occurs when using the optical viewfinder for macro photography, we recommend that you use the LCD monitor to compose your photographs when shooting extreme closeups. * Parallax refers to the difference

between what is seen in the viewfinder and the actual image recorded through the camera’s taking lens.

View through optical viewfinder

Image actually recorded by camera

2524

+ 35 hidden pages