Kongsberg TTC 30, TTC 10 User Manual

TTC 30 and TTC 10 Quick Reference Guide

For detailed operation description, see Online help. For more detailed information, see the TTC 30 and TTC 10 Instruction Manual.

Getting started

1. Disconnect the TTC power cable
from charging station.

2. Place the TTC unit in a suitable
location.

3. Open the TTC case by pressing the

handle knobs and pull the handles

up.

4. Turn on the main power switch
ON (D) in order to boot up the PC
program (starting up the system

will take approx. 1.5 minutes).

- Online help is available on
TTC screen/APOS screen.

Turning unit OFF

1. Switch ON/OFF button (D) to OFF

position.

Acoustic Test

1. Connect the Test transducer cable
to the upper right connector (B).

2. Place the Test transducer (Y) face
to face with the transponder.

3. Communication between the
TTC and the transponder may
easily be tested by selecting the

ACOUSTIC TEST tab → enter
S/N → Transponder channel No.
→ INTERROGATE.

4. A green lamp will ash on the

display if there is acoustic contact
wth transponder.

Transponder Conguration

Establish connection with TP:

1. Connect the Serial line cable to
the upper left connector (A) on
TTC and the other connector to the
bottom of the transponder (X).

2. Select TRANSPONDER
CONFIGURATION tab in the
main menu.

3. The TTC will automatically update
TP information when connected.

4. The TTC is ready for conguration

when GREEN line is visible.

- If the line is red and no contact

is made with the TP → check all

cables and try again.

5. Press INTERROGATE button
again to stop ACOUSTIC TEST.

6. To set TTC POWER use left/
right arrows to choose power level

→ press SET to conrm your

selection.

Note! The Test transducer is made for

communication in air so make sure

to limit TTC POWER to LOW.

Setup New Conguration:

1. Press buttons on the right hand side
of the screen to change TP info.

2. Press DOWNLOAD NEW
CONFIGURATION to update TP.

3. New TP info will appear on left
hand side of screen.

- If DOWNLOAD NEW
CONFIGURATION is
unsuccessful a red box will appear
on right hand side with message

'Download cong failed' → check

all cables and try again.

351069/Rev.C/January 2012

TTC 30 and TTC 10 Quick Reference Guide

For detailed operation description, see Online help. For more detailed information, see the TTC 30 and TTC 10 Instruction Manual.

TTC 30 and TTC 10 Front panel

The TTC 30 and TTC 10's touch screen is mostly used when performing

Acoustic test and Transponder conguration. All other connections and

buttons are explained below:

A Connector (with protection cap)

for transponder Serial line used for

transponder conguration.

B Connector (with protection cap) for Test

transducer used for acoustic testing.

C Connectors for USB and LAN. For

service personnel only.

(Connection to network and possible

APOS/PC program download via USB.)

- Placed behind a waterproofed cover.
Turn the screws to lift cover.

D Power ON/OFF switch.
G Trackball - used to position the cursor

on the screen. A trackball movement +
pressing the trackball down moves the

cursor.

Left button: Used to click on buttons, •

operate menus and select displayed
symbols.

Right button: Used to display menus •
and pop-up windows.

The most common trackball operations

are; pointing, clicking and dragging.

H Stand-by wake up, with two LEDs

indicating status.

I Display light (-/+) adjustment.
J Power connector - male 3-pins connector

for the mains cable.

- This cable (see L) is used to
connect the TTC to a standard 110/230
Vac mains supply, to recharge the
internal battery.

K Gas lift springs.
L Battery charge cable in lid folder -

supplied with the unit.

M Battery status indicator. The battery

should last for approx. 3 hours of
continual use.

Charging the battery

During operation:

If the TTC battery indicator
indicates LOW power then
connect the charging cable.

To start charging:

Mains cable is stored in the

lid folder.

1. Connect the cable to the
Power connector at the front
of the TTC

Stand-by mode

When TTC PC is not in use
for a certain time, it will go
into Stand-by mode. This
means that the screen will

turn black. Touch the screen
or move the trackball to

return to Operation mode.

Support

- see (J) marked in the TTC
Front panel overview on the
left side of this page.

Note! Use the mains cable

supplied with the system.

2. Connect the other end of
the cable into a 110/230 Vac
mains supply.

• It is important that the

battery is fully charged
when the TTC is stored.

TTC Maintenance

Clean the unit and charge the
battery at least every 12 months.

All Kongsberg Maritime products:
Phone 24 hour: [phone]

E-mail: [e-mail]

HiPAP, HPR, Transponders, HAIN and ACS:
Phone 24 hour: [phone]

Email: [e-mail]