MULTI EFFECTS LED TWINKLING LASER SHOW SYSTEM
User's Manual
Read this manual before using. Do not attempt to open the housing
or repair this device by yourself without contact us!
DMX Address Chart
This chart lists the DMX dipswitch setting for DMX address 1 through 511. Follow the
instructions below to configure fixture dipswitches with you desired DMX address.
DMX Address Quick Reference Chart
Page 9
DipSwitch Position DMX Address
DipSwitch Position
Notes:
1. DMX console can not be used in Master-Slave operation (Sound Active or AUTO mode ).
2. There should be only one master unit in Master-Slave operation.
Unpacking:
Thank you for purchasing this product. Please read user guide for safety and operations inf-
Troubleshooting
ormation before using the product. Keep this manual for future reference. This product can
create perfect laser programs and effects since it has passed a series of strictly tests before
1. If the power supply indicator doesn't light up and the laser doesn't work, please check the
delivery. Please check the attachments listed on the page after opening the carton. In the
power supply and the input voltage.
event of carton damage or attachment missing in transit, please contact your dealer or our
2. In Stand-Alone operation, if the power supply indicator is light up and sound active indic-
after sales service department.
ator isn't light up, but the laser is shut off doesn't work.
A. Because sound is too small make for laser shut off in sound active, please increase the
Attachments:
music volume or increase audio sensitivity with sensitivity knob, please check as below.
1. Laser Light: 1PCS
B. Please check if unit has been set up in slave mode, then set up in master mode. 2. Power Cable: 1PCS
3. In Master-Slave operation, slave unit don't function, please check as below.
3. User Guide: 1PCS
A. Make sure to there's only one master in the chain, and the others are set in slave mode.
B. Make sure to control the unit without DMX console controlling.
C. Make sure to take a good quality power cable and connection.
Notice:
4. In DMX mode operation, the laser is OFF and the DMX signal indicator is unlighted, pl-
1. Do not exposure the human eye direct to laser beam.
ease check as below.
2. Do not turn on and off the unit frequently.
A. Make sure to set up the DMX mode.
3. Before using this unit make sure the power supply is ground.
B. Make sure to have a good connection. 4. This unit is intended for indoor use only and should be prevented form water, moisture
5. In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal and shake. The working temperature of this unit is 18～30℃, do not use this continuously
indicator is flashing, please make sure the DMX console and unit have the same channel. over 4 hours, otherwise it shortens the lifetime of the unit.
6. If the unit is fail, please turn off the unit, then turn on again after 5 minutes.
5. Use cleaning tissue to remove the dust absorbed on the external lenses periodically to op-
timize light output.
After trying the above solution you still have a problem, please contact your dealer or 6. Do not remove or break the warranty label, otherwise it void the warranty.
our company for service.
7. Always replace with the exact same type fuse, replacement with anything other than the
specified fuse can cause fire or electric shock and damage your unit, and will void your ma-
nufactures warranty.
DANGER
LASER RADIATION AVOID EXPOSURE
TO BEAM CLASS 3B LASER PRODUCT
Page 8 Page 1
General instructions
!
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
1. Voltage: AC110V-130V/200V-250V, 50HZ-60HZ/ Fuse: 2A/250V 1. Install the units in a suitable position (laying or appending).
2. Rated Power: 20W 2. Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO
3. Light: G:50mW+ R:100mW+100mW+3W RGB LED mode. The others must be set to Slave mode, set dipswitch to select Slave mode.
4. Working Modes: DMX, Sound Active, AUTO, Master-Slave 3. Use standard XLR microphone cable chain your units together via the XLR connector
5. DMX Control Channel: 10 channels on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
6. Graphics & Effects: Control the speed of two DC-step motors can create more than 4. Turn on the all units' power, the units begins reset, then the unit begins working. The
20 kinds of smooth and random changeable grating patterns .it is variable,sometimes slave units will react the same as the master unit.
it looks like egg rolling,fish spitting bubbles,or form triangular plum flower,making you 5. The units will react to the low frequencies of music via the internal microphone. Adjust
very superized.the red and green color can freely combinated and changed,clockwiseor
the audio sensitivity knob on the back of the master unit to make the unit more or less se-
counterclockwise rotation from time to time
nsitive in sound active.The panel has LED indicating for sound active.
7. Interface: 3 pins XLR jack for DMX or Maser-Slave linking
8. Size: L*W*H=100*300*200mm
9. Weight: 4.5Kg
1. Various working modes Universal DMX Operation (DMX mode)
Includes four working modes as DMX, Sound Active, AUTO and Master-Slave Control
This mode allows you to use universal DMX-512 console to operate.
for different applications. 1. Install the units in a suitable position (laying or appending).
2. DMX control
2. Use standard XLR microphone cable chain your units together via the XLR connector
The unit has 5 channels functions to control system mode, laser beam running direction, on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
running speed, twinkle speed and color setting in DMX mode. The unit has BLACK 3. Assign a DMX address to each the unit using dipswitches, see the "DMX Address Quick
OUT fun-ction. The uint will shut OFF if no DMX512 signal.
3. Master-Slave function
The system allow link many units (as slave unit) together to doing synchro job without
console in sound active or AUTO mode.
4. LED indicating and shut-off function
In sound active mode, the unit's panel has LED indicating for sound active. The unit will
shut off after 8 seconds when the music stops. Reference Char".
5. DPSS Laser
4. Turn on the all units' power, the units begins reset, then the unit begins working.
Use Diode-Pumped Solid State laser, stable output and long working life. 5. Use DMX console to control your units.
Page 2 Page 7
Technical Specification
Features
POWER
1：MASTE R:SOUND/ AUTO
N：SLAVE
2：SLAVE
POWER
POWER
1：DMX M ODE
N：DMX MODE
2：DMX M ODE
DMX Sign al
POWER
POWER
POWER
Dipswitch #10 is use to set master or slave mode. Master modes have sound active and
AUTO mode. Slave modes have DMX and Slave mode. The units automatically identify
DMX or SLAVE mode by data receives. Dipswitch #9 use to is set sound active or AUTO
mode in master mode.
DMX address calculation
For DMX mode, DMX address from #1 to 9# dipswitches must be set, the address is set
from 1 to 511. Each dipswitch represents a binary value. Front Panel Figure
Dipswitch Value Dipswitch Value 1. Laser Aperture 2. Sound Active Microphone 3. Power Indicator:Red
＃1
1
＃6
32
4. Sound Active Indicator:Blue. The LED will twinkle when a stimulated sound signal is
＃2
2
＃7
64 received form the MIC 5. LED aperture
＃3
4
＃8
128
＃4
8
＃9
256
＃5
16
＃10
DMX, Set to "0"
One unit has 5 channels, so each unit must be assigns 5 channels at least. We may assign 8
channels for one unit, then DMX address = 8*N + 1, N=0, 1, 2, 3 …… Example,
One loop address=1, two loop address=9, three loop address=17, four loop address=25
Loop Address Binary Dipswitches
1 1 100000000 ＃1
2 9 100100000 ＃1+#4
Rear Panel Figure
3 17 100010000 ＃1+#5
1. Dipswitches: Function Setting
2. DMX Signal Indicator: Green. The LED will
4 25 100110000 ＃1+#4+#5
twinkle when DMX or Master-slave 3. Cooling Fan
The dipswitches setting for DMX address see the " DMX Address Quick Reference Chart ".
4. Audio Sensitivity Knob 5. DMX or Linking Jack
6. Switch ON/OFF 7. Power plug
Stand-Alone Operation (Sound Active, AUTO mode)
The mode allows a single unit to react to the beat of the music in the master mode. Sound Active
1. Install the units in a suitable position (laying or appending). The change of the laser pattern is controlled by sound, that is, the rhythm of the sound
2. Set dipswitch to select Sound Active or AUTO mode.
control the effect of the changing laser pattern. Turning the sensitivity knob in the clockwise
3. Turn on the unit power, the unit begins reset, then the unit begins working.
direction to increase the fixture’s sensitivity to sound, the knob in the counter clockwise
4. The unit will react to the low frequencies of music via the internal microphone. Adjust
direction to decrease. The laser diode will automatically turn off after 8 seconds when the
the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in music stops.
sound active.The panel has LED indicating for sound active.
AUTO
Auto cycles the built-in programs without being controlled externally. It has no laser OFF.
Page 6 Page 3
Front/Rear Panel
Operation
Function & Setting
1
2
3 4
1
5
1 2
4
6
7
3
5
DMX Control
The system only accepts the DMX512 signal of international standard to control the system
LED OFF
mode, the laser beam ON /OFF, running direction, running speed and twinkle speed etc. R-G-B-RG-RB-GB-RGB
R-G-B AUTO change
DMX Control Parameter Chart
RG-RB-GB-RGB AUTO change
R-G-B-RG-RB-GB-RGB AUTO change
Close, laser OFF
R-G-B Sound Active
Sound active mode
RG-RB-GB-RGB Sound Active
AUTO mode R-G-B-RG-RB-GB-RGB Sound Active
DMX mode No strobe
Red Auto strobe
Green Strobe in Sound Active
Red and Green
red, green and RG in AUTO mode
When the CH1 is selected the DMX mode(DMX value is 50～100), you can use channel
Red, green Auto change CH2, CH3 and CH4 to control laser beam, otherwise, CH2, CH3 and CH4 are invalid.
Red, green and RG in Sound Active
red, green in Sound Active
Function setting
No flashing
Auto flashing, slow to speedy
flashing in Sound Active
No spin
Counter Clockwise spin
Clockwise spin Uses dipswitches to assign a unit’s function: DMX/slave, or sound active, or AUTO mode.
Auto spin
For the unit is DMX mode, set the DMX address using dipswitch. Each dipswitch represents
0 is slow, 255 is speedy a binary value. See the “Function chart”.
normal pattern
beam longer or shorter
Page 4 Page 5
Channel Function Value Description
CH9
LED light color
change
0
1～55
56～99
100～159
160～219
Channel Function Value Description
CH1
Mode
0～63
220～223
64～127
224～239
128～191
240～255
192～255
DH10
LED light Strobe
0～31
CH2
Laser Color
Selection
0～31 32～239
32～63 240～255
64～95
96～159
160～219
220～239
240～255
DH3
Flashing
0～19
20～239
240～255
CH4
Bubble Pattern
0～255
Over 30 kinds of patterns
CH5
Bubble Pattern
0～255
CH6
Bubble Spin
Direction Control
0～9
10～99
100～199
200～255
CH7
Bubble Spin speed
0～255
CH8
Fireworks beam
line length
0～64
65～255
Function Chart
Loading...