Kompernass PKGS1450 User Manual
CHOP AND
MITRE SAW
Before you begin reading this information, please unfold the page with the illustrations
and familiarize yourself with all functions of the tool.
Kompernaß GmbH
Burgstraße 21
D-44867 Bochum (Germany)
Last information update: 07 / 2007 · Ident.-No.: PKGS1450 Laser - 072007-1 / UK / IE
CHOP AND MITRE SAW
PKGS 1450 LASER
Operating and safety instructions
GB / IE Operating and safety instructions Page 5
t y u
e
w
Q W
E
r
R
T Y
q
I }
O
PY U
}
A B C
A
o
p
[
]
H
G
S
D E F
U
{
D
i
F
a
b
Y
c d
e
f
Before reading, unfold the page containing the illustrations
and familiarise yourself with all functions of the device.
The following icons / symbols are used in this instruction manual:
Content
V~
Read instruction manual!
Observe caution and safety notes!
Caution – electric shock!
Dangerous electric current – danger
to life!
Caution, laser!
Do not expose yourself to
laser radiation.
Voltage To work safely
W
n
0
Watt (performance)
Rated idle running speed
wear ear protectors, a breathing /
dust mask and safety glasses.
Protection category II
Introduction
Your safety ..................................................................................................... Page 6
Proper use...................................................................................................... Page 6
Features and equipment ................................................................................. Page 6
Included items ................................................................................................ Page 6
Replaceable parts .......................................................................................... Page 7
Technical information ..................................................................................... Page 7
Safety
Safety advice relating specifically to this saw ................................................ Page 7
Operation
Assembly ....................................................................................................... Page 9
Checking and setting your saw ...................................................................... Page 9
Operation ....................................................................................................... Page 10
Connecting a dust extraction device ............................................................... Page 10
Unlocking and switching the machine on and off............................................ Page 11
Switching the laser on and off and adjusting it ............................................... Page 11
Setting the speed ........................................................................................... Page 11
Transporting the machine ............................................................................... Page 11
Attaching the laminate cutting attachment and cutting laminate .................... Page 11
Mitre cuts – turning the saw table .................................................................. Page 11
Inclined cuts – inclining the saw motor unit .................................................... Page 12
Making a combination cut .............................................................................. Page 12
Changing a saw blade .................................................................................... Page 12
Tips and tricks ............................................................................................... Page 12
Cleaning
Maintenance and cleaning ............................................................................ Page 13
Disposal .......................................................................................................... Page 13
Information
Service ........................................................................................................... Page 13
Manufacturers’ declaration of conformity
....................................................... Page 13
5 GB/IE
Introduction
Chop and mitre saw
PKGS 1450 LASER
Chop, mitre and combination cuts
L Introduction
L Your safety
Please make sure you familiarise yourself
fully with the way the device works before
you use it for the first time and that you
understand how to handle electrical power tools
correctly. Further details can be found in the operating
instructions.
In addition, you must also observe the general safety
advice contained in the accompanying booklet. Keep
these instructions in a safe place. If you pass the
device on to anyone else, please ensure that you
also pass on all the documentation.
L
Proper use
For sawing solid wood, chipboard and plastic. With
the laminate cutting attachment
machine is suitable for laminate and material up to
20 cm wide. Please note that the blade pre-installed
in the saw as supplied is intended for use with wood
only. Any other use or modification to the device shall
be considered as improper use and could give rise
to considerable dangers. The manufacturer will not
accept liability for loss or damage arising from
improper use. Not suitable for commercial use.
L
Features and equipment
Q
Saw motor unit
W
Switch handle
E
Safety lever
R
Sliding roller (with automatic blade guard)
T
Saw table
Y
Lateral support stirrup
U
Lateral support stirrup clamp screws
I
Mitre angle stop
O
Saw table setting knob
6 GB/IE
{
in place the
P
Mitre angle scale
{
Laminate cutting attachment
}
Mounting holes
q
Stop plate
w
Saw motor unit setting knob
e
Rear support stirrup
r
Sawdust removal connector
t
Laser beam emission opening
y
Screw (for attaching the saw blade)
u
Outside flange
i
Laser On / Off switch (Fig. C)
o
Transport lock (Fig. A)
p
Saw blade depth setting screw (Fig. A)
[
Scale on the saw motor unit (Fig. A)
]
Mitre angle / 0° setting screw (Fig. A)
A
Saw motor unit mounting screws (Fig. A)
S
Mitre angle / 45° setting screw (Fig. B)
D
On / Off switch (Fig. C)
F
Rotation speed selector wheel (Fig. C)
G
Table insert (Fig. B)
H
Laser setting screw (Fig. B)
Included items
L
1 Chop and mitre saw
1 Laminate cutting attachment
2 Lateral support stirrups
{
Y
1 Sawdust collection bag (a)
2 Screw clamps (b)
2 Carbon brushes (c) (see section on maintenance)
2 Allen keys (d), sizes 5 mm and 6 mm
1 Locking spanner (e)
1 Socket spanner (13 mm) (f)
1 Universal saw blade: 250 x 30 x 2.35 mm,
80 HM - teeth (3.2 mm)
1 Saw blade for wood
(supplied installed): 250 x 30 x 1.8 mm,
36 HM - teeth (3.0 mm)
1 Operating instructions
1 Booklet “Guarantee and service”
1 Booklet “Containing general safety advice”
Introduction / Safety
L Replaceable parts
You can replace the following parts yourself.
When you do this always observe the relevant operating instructions and safety advice.
- Sawdust collection bag (a)
- Laminate cutting attachment
- Stop plate
q
{
- Saw blade
Have any other maintenance and repair tasks carried out by our service centre or an accredited electrical equipment repair centre.
L
Technical information
Nominal output: 1450 W
Nominal voltage: 230 V ~ 50 Hz
Nominal speed: n
1800 - 4500 min
0
-1
Circumferential speed: 24 m / s – 55 m / s
Weight: 14.5 kg
Protection class: II /
&
Sound pressure level: Lp = 95.5 dB (A)
Sound power level: Lw = 108.5 dB (A)
Vibration: 2.5 m / s
2
Saw blade for wood
(supplied installed): 250 x 30 x 1.8 mm,
36 HM - teeth (3.0 mm)
Universal saw blade: 250 x 30 x 2.35 mm,
80 HM - teeth (3.2 mm)
Cutting capacity:
Cutting width: max. 140 mm (without
laminate cutting attachment)
max. 200 mm (with laminate
cutting attachment)
Cutting depth: max. 65 mm
L Safety
Safety advice relating
specifically to this saw
J Ensure that the device is always used in accord-
ance with the advice in these operating instructions and only by persons over 18 years of age.
J
by children.
J In addition, you must also read the advice in the
accompanying booklet containing safety advice
before using the device for the first time.
J Check that all moving parts on the tool are working
properly, can move freely and are not damaged.
All parts must be correctly attached and fulfil all
the requirements necessary to allow the electrical
tool to operate properly.
J Carry out the following before each use:
- check the saw for damaged parts or safety
- check the saw blade for quality / condition,
- check that the saw blade is properly attached
J
Caution! A damaged mains lead
presents a serious danger to life from electric
shock. The service centre for your country is
shown in the guarantee documentation.
J Have repairs carried out only by an electrician or
the relevant service centre.
Keep children away from the device.
Store the device indoors in an enclosed,
dry place where it cannot be reached
equipment and if necessary have them
replaced by an electrician.
sharpness, cleanliness and free movement.
and does not wobble. Attach the saw blade
by placing the locking spanner (e) on the outer flange
attaching the saw blade)
u
and tightening the screw (for
y
counter-clock-
wise.
To avoid danger to life
from electric shock:
Do not operate the device if the
mains lead or mains plug is damaged.
7 GB/IE
Loading...