Kompernass KH 4098 User Manual

  Low Voltage Halogen Spotlight KH 4098
Operating instructions
Kompernaß GmbH · Burgstr. 21 · D-44867 Bochum
www.kompernass.com
ID no.: KH4098-10/06-V3
Cleaning
Wipe the appliance with a damp cloth. Do not use aggressive or chemical cleaning agents. These would result in damage to the appliance.
Disposal
Under no conditions should the appliance be disposed of with normal household waste!
Dispose of the appliance through an approved disposal centre or at your community waste facility. Observe the currently applicable regula­tions. In case of doubt, please contact your waste disposal centre.
Service
DES Ltd
Units 14-15 Bilston Industrial Estate Oxford Street Bilston WV14 7EG Tel.: 0870/787-6177 Fax: 0870/787-6168 e-mail: support.uk@kompernass.com
Kompernass Service Ireland
c/o Irish Connection 41 Harbour view Howth Co. Dublin Tel.: 087-99 62 077 Fax: 18398056 e-mail: support.ie@kompernass.com
q
w
eyt r
u
i
a
o
KH4098_IB_EN.qxd 16.10.2006 16:09 Uhr Seite 1
Description of the appliance
q
Colour discs
w
Power plug
e
Power cable
r
Transformer
t
Connecting plug
y
Coupling nut
u
Cable
i
Underwater lamp
o
Lamp cover
a
Outer race
Commissioning
Assembly
1. Insert the connecting plug
t
into the
transformer
r
.
2. Slide the coupling nut
y
onto the
connecting plug
t
and screw it tight.
Placing the coloured disc
1. Lay the slot of the coloured disc qon one of the two securing hooks of the underwater lamp
i
.
2. Carefully press the coloured disc
q
down on the opposite side until it audibly engages.
3. If you wish to exchange the coloured disc
q
, lightly press a securing hook outwards and at the same time press the coloured disc to the side.
Placing the underwater lamps
Ensure that a mains power socket is in the close vicinity.
Place the underwater lamps
i
as desi­red. The underwater lamps
i
can be opera-
ted both in and out of water.
Align the underwater lamps
i
with the assistance of the 5-stage pivoting device.
Insert the power plug
w
into a wall
power socket.
In permanent installations we recommend that the transformer
r
is fastened down
with the fixing holes.
Changing bulbs
1. Turn the outer race aof the underwa­ter lamp
i
in the direction of the arrow (anti-clockwise). You can now remove the outer race
a
.
2. Remove the transparent lamp cover­ing
o
.
3. Pull the halogen lamp, complete with the housing, upwards.
4. Holding the housing firmly, carefully pull the halogen lamp, complete with reflector, out of the housing.
5. Insert the new halogen lamp into the housing and then press both of them back down again.
NOTE: Ensure that the sealing ring is
not displaced.
6. Lay the lamp cover oonto the under­water lamp
i
.
7. Place the outer race
a
on the under-
water lamp
i
such that the tenons fit
into the rebates of the outer race
a
.
Turn the outer race
a
in a clockwise
direction until tight.
Safety instructions
Danger of injury
• Connect the appliance only to correctly installed mains power sockets with a supply voltage of 230 V~ at 50 Hz.
• In the event of operational malfunction and for cleaning, always remove the power plug from the wall socket.
• Always remove the power cable from the socket by pulling on the plug, not on the power cable itself.
• Do not crease or crimp the power cable and lay it in such a way as to prevent anyone from stepping on or tripping over it.
• Should the power cable or the appliance become damaged, you must have them repaired by qualified specialists before using them again.
• Always keep the appliance beyond the reach of children.Do not allow children to use it.
• The appliance may not be operated in or next to swimming pools. Risk of injury!
Attention
• Always remove the plug from the wall socket before removing the halogen lamps.
• Allow the halogen lamps to cool down before removing them. The halogen lamps will become very hot. There is a danger of being burnt!
• Do not use extension cables!
• The maximum submersing depth for the underwater lamps amounts to 0,5m. Do not submerse them any deeper. The appliance would be irreparably damaged.
• Take steps to ensure that the transfor­mer cannot fall into the pond or water container. The appliance would be irreparably damaged.
• The flexible power cable of the trans­former cannot be exchanged. Should the power cable be damaged, the transformer must be exchanged as a complete unit.
• In exterior areas only use power sockets of the protection class IPX4.
Intended use
The low voltage Halogen spotlight is intended for the illumination of gardens or garden ponds. It is intended exclusively for private usage, not for commercial purposes!
Items supplied
3 Halogen spotlights Cable 12 Colour discs (3x red, yellow, green and blue) Power transformer Operating instructions
Technical data
Mains voltage: 230 V~ / 50Hz Light bulb : 12 V, 10 W, Type MR11 Power transformer: Spraywater protected Protection class:II
Plug of the protection type: IP44 Lamps of the protection type: IP68
KH4098_IB_EN.qxd 16.10.2006 16:09 Uhr Seite 2
Loading...