Kolpin 86360 User Manual

Owners Manual and Operating Instructions

ATV SPREADER

SAFETY WARNINGS AND PRECAUTIONS

Warning: When using tool, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!

1. Keep work area conditions. Cluttered areas invite injuries.

2. Additional work area conditions. Do not use machines or power tools in damp or wet

locations. Do not expose to rain. Keep work area well lighted.

3. Keep children away. Children must never be allowed in the work area. Do not let them handle
machines, tools or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust.
Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work
of a larger industrial tool. There are certain applications for which this tool was designed. It will
do the job better and more safely at the rate for which it was intended. Do not modify this tool
and do not use this tool for a purpose for which it was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts.
Protective, electrically non-conductive clothes and non-skid footwear are recommended when
working. Wear restrictive hair covering to contain long hair.

7. Use eye protection. Always wear ANSI approved impact safety glasses underneath a full face
shield during use. Also, wear heavy duty work gloves.

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across
running
machines.

9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. The handles must be kept clean, dry and
free from oil and grease at all times.

10. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before starting work.

11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you
are tired.

12. Check for damaged parts. Before using any tool, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform its intended function.
Any part that is damaged should be replaced.

13. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty. Only use accessories intended for use with this
tool.

14. Do not operate tools if under the influence of alcohol or drugs. Read warning label on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the tool.

WARNING: The warnings, cautions and instructions discussed in this instruction manual can

not cover all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which can not be built into this product, but
must be supplied by the operator.

SPECIFIC SAFETY RULES

1- Always wear protective clothing, eyewear, and dust mask to prevent contact with chemical and other

materials being applied with this machine.

2- Remove any material in hopper before lifting or detaching this machine from the vehicle.
3- Care must be taken when lifting this machine so as not to cause personal injury or equipment

damage. Never attempt to install this machine to the vehicle alone. Recruit the help of someone to
assist when attaching and detaching this machine from the vehicle.

4- Refer to the material packaging or the Material Safety Data Sheet for precautionary measures

required when handling materials to be applied.

5- Before attaching this machine, consideration must be given to the load capacity of the vehicle. Refer

to the owner’s manual of the vehicle for rated load capacity. Be sure to take into account the weight
of this machine 20lbs and the weight of the material to be placed in the hopper when calculating the
total load.

6- Keep hangs away from any spinning object.

HOW TO OPERATE SAFETY

1- Read, understand, and follow all product label information provided on the material being applied.
2- An adjustable solid stop is provided that allows the operator to adjust to the desired opening position

on the rate setting control prior to operation of the vehicle. This allows repeatability to the stop
without the need to look at the control while operation the vehicle.

3- Establish the correct rate and then lock the stop in that position using the thumb wing nut on the

setting control.

PRODUCT SPECIFICATIONS

1- 12 Volt motor with vinyl coating mounts to front or rear luggage rack, lever and gauge mounts to

either side.

2- Fits most brands of ATVs and comes with wiring harness for easy installation.
3- Heavy 80-Lb load bearing capacity.
4- Capacity:1900 cu.in.