Kole Audio electronic KMX User Manual

Kole Audio KMX Woofers
Congratulations on your purchase of one of the finest woofers available for your vehicle today.
The KMX is designed for the serious SPL enthusiast. Our engineers developed a new finished aluminum dust cap to aid in thermal transfer and also help to lower the resonant frequency. The aluminum dust cap is direct­coupled to the voice coil former, and serves to draw 50% of the heat away from the voice coil to the dust cap, thus acting as a voice coil heatsink. This “heatsink” action serves to maintain the strength of the bond between the cone and the voice coil by preventing adhesive breakdown due to thermal buildup. This revolutionary dust cap allows the woofer to handle 56% more power without sacrificing sensitivity. Your competition will never know what hit them.
Please take a few moments to fill out the warranty card and review this manual before installing this woofer for proper connections and box sizes.
Two Piece, Die-cast Aluminum Basket Non-Pressed Paper Cone with Aluminum Dust Cap Large Roll Treated Foam Surround Woven “Through-the-Spider” Tinsel Leads Dual CONEX Spiders Dual 2-ohm Voice Coils 1-piece rubber gasket
Black/Yellow Wrinkle Coat with Diamond Cut Finish
Heavy Duty Connectors
SPL: 10” – 89 dB 12” – 90 dB 15” – 92 dB
Magnet size: 10”- 170 oz. 12” –270oz. 15” – 270 oz.
BASV/Kapton hybrid 18 awg voice coil:
RMS Power (watts): 10” – 700 12” – 800 15” - 1000 MAX Power (watts): 10” – 1400 12” – 1600 15” – 2000
KMX-10 Fs 35.2 Hz 27.39 Hz 29.6 Hz
Vas 0.48 Cu. Ft. 1.45 Cu. Ft. 1.79 Cu. Ft. Qms 5.27 5.13 4.685 Qes 0.479 0.418 0.484 Qts 0.439 0.3867 0.439 Xmax 0.473” 0.473” 0.748”
Design Features
10” - 3” 12” - 3” 15” - 4”
Thiele / Small Parameters
KMX-12 KMX-15
Model Sealed Box Size Ported Box Size Tune Freq. # of Ports Port (dia x length)
KMX-10 NA 1.75 cubic feet 40 Hz 1 4" x 11" KMX-12 NA 2.4 cubic feet 40 Hz 1 4" x 8.5" KMX-15 NA 3.0 cubic feet 40 Hz 2 4" x 11.25"
Determine the dimensions of your enclosure.
Be certain the box dimensions that you have designed will fit in the location you have
chosen in your vehicle. Sometimes making a cardboard box with the same outside dimensions is helpful.
It is recommended to use ¾ inch thick MDF (medium density fiberboard) for your
box.
Use a “T” square to verify precise right angle cuts before you assemble the box.
Use high quality wood glue and screws to assemble the box to guarantee an airtight
box that will not come apart due to excess vibration and pressure.
It is recommended for sealed enclosures to stuff the interior of the box about 50 –
75% full of fiberglass insulation or Dacron fiberfill for increased sound damping and woofer performance.
For ported enclosures, it is recommended to staple 1” thick fiberglass insulation to the
interior walls of your box.
Use slide on connectors for spade style connectors or bare wire for push and screw
terminals. Do not solder the wires to the factory connectors as this may cause damage to the voice coil or tinsel lead and may void your warranty.
The following page will give you a few different options to match the impedance of the woofers to the impedance capability of the amplifier. Please look and follow the diagrams closely to insure maximum woofer performance.
Recomme nded box sizes
Building the Enclosure
Recommended wiring
Loading...
+ 1 hidden pages