Kold-Draft MGT350W Installation Manual

Marine Cuber with Manifold

KOLD-DRAFT

CLASSIC

M

GT

350

W

®

Installation & Operation Instructions

KOLD-DRAFT

Ice Machine Products

1525 East Lake Road, Erie, PA 16511-1088
814/453-6761
FAX [phone]

©2004 KDIndustries, Inc., Erie, PA U.S.A.
Printed in U.S.A. 3/04
508 1060 01

A Tradition of E xcellence I n I ce Equipment.

INSTALLATION AND OPERATION INSTRUCTIONS

FOR

KOLD-DRAFT

MARINE MGT3

50 SERIES ICE

CUBERS

®

CHECK FOR FREIGHT DAMAGE BE PROCEEDING: Even though damage to the
carton may not have been evident, check for hidden damage and contact freight carrier
immediately if necessary to file a claim.

THIS EQUIPMENT MUST BE INSTALLED IN COMPLIANCE WITH THE
APPLICABLE FEDERAL, STATE/PROVINCE, AND/OR LOCAL PLUMBING,
ELECTRICAL, AND HEALTH/SANITATION CODES AND REQUIREMENTS.

CAUTION:

{

RISK OF PERSONAL INJURY, PROPERTY DAMAGE, EQUIPMENT
FAILURE, OR FIRE.

{

Refer all maintenance to qualified personnel .

{

Never operate this equipment with covers, panels, or other parts removed
or not properly secured.

{

Warn all users to clean up spillage immediately, keep storage bin doors closed,
and report any apparent leakage or unusual sounds to responsible
maintenance personnel.

INSTALLATION

1. Position the ice storage bin so that the following minimum clearances will be
available around the i ce maker for ventilati on and utility connections:

REAR and TOP: 6 inches
RIGHT SIDE: 6 inches
LEFT SIDE : 6 inches

508106001 Rev: 8/02

2. Level the bin with adjusters on legs, or by shimming if the bin is to be sealed to

Consult local codes for sui table connections to th

e building drai ns.

the floor. If gaps due to shi ms are greater than 1/8 inch, instal l a cove molding
around the bin bottom. Seal the bin or molding to the floor with NSF Certified
RTV sealant (Dow-Corning RTV 732 or equal).

3. Remove the cuber cabinet TOP panel as follows:
Lift from the front and pull forward until the rear clip is disengaged from the
chassis.

CAUTION:

{

RISK OF PERSONAL INJURY OR EQUIPMENT DAMAGE.

{

Use a suitable lifting means and be careful of sharp edges.

4. Remove the remaining cuber cabinet panels as fol lows:
FRONT: Remove the (4) screws at the bottom and front-sides, pull forward.
SIDES : Pull forward and lift to disengage the clips from the chassis.
NOTE: When re-installing the panels, be sure that the screws engage the TOP
panel.

5. Remove the ice chute/drain pan. Drain tube assembly shown below is packed
with the drain pan.

6. Install gasketing on top of bin if required. Gasket material must be positioned
so that it extends to the outside edge of the perimeter of the cuber chassis when
the cuber is in place.

7. CAREFULLY place the cuber onto the gasketed bin, noting the al i gnment of the
mounting holes in the chassis if mounting means are provided on the bin.
Follow the bin installation instructions for securing the cuber to the bin.

WARNING:

{

RISK OF CONTAMINATION OF ICE IN THE BIN.

{

Provide separate, unconnected, drains for the ice maker and the bin.

{

8. Install the drai n pan/ice chute. Route the drai n tube assembly through the rear
of the bin, and clamp the tubing to the drain pan nipple.

9. Electrical, water and drain locations are shown on the following drawing. All
dimensions are in inches.

508106001 Rev: 8/02

-2-

10. Purge the potable water supply line.

11. Remove the water plate shipping strap.

12. Route the bin thermostat capillary tube through the grommet in the right end
frame wall and under the ice chute. See the diagram and notes following for
location and securing of the capillary tube.

13. If start-up will not occur immediately, secure all cuber cabinet panels now.

508106001 Rev: 8/02

-3-