Kolcraft RF001 User Manual

Bridgehampton Convertible Crib Assembly Instructions

Instructions d'assemblage pour lit de bébé transformable Bridgehampton

Instrucciones de montaje de la cuna convertible Bridgehampton

Q001

WARNING

FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD

RESULT IN SERIOUS INJURY OR DEATH.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR

¢ FUTURE USE.

¢NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS

BECAUSE THEY CAN CAUSE SUFFOCATION.

¢TO REDUCE THE RISK OF SUDDEN INFANT DEATH SYNDROME (SIDS), PEDIATRICIANS

RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR BACKS TO SLEEP, UNLESS OTHERWISE ADVISED BY YOUR PHYSICIAN.

¢INFANTS CAN SUFFOCATE ON SOFT BEDDING. NEVER ADD A PILLOW OR COMFORTER.

NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.

STRANGULATION HAZARD

¢STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING

AROUND A CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.

¢TO HELP PREVENT STRANGULATION, TIGHTEN ALL FASTENERS. A CHILD CAN TRAP

PARTS OF THE BODY OR CLOTHING ON LOOSE FASTENERS.

¢DO NOT PLACE CRIB NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES

MAY STRANGLE A CHILD.

FALL HAZARD

¢WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST

POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.

¢STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF

35 IN. (89 CM).

¢CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR OTHER FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER FASTENERS. DO NOT USE CRIB IF ANY PARTS ARE MISSING, DAMAGED, OR BROKEN. CONTACT KOLCRAFT ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.

¢IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS. ¢FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB. ¢INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS

TOO SMALL.

¢ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 IN. (69 CM) BY 51-5/8 IN.

(131 CM), WITH A THICKNESS NOT EXCEEDING 6 IN. (15 CM). THE DIMENSIONS OF THE MATTRESS SHOULD BE TAKEN FROM SEAM TO SEAM.

¢PREVENT BURNS. KEEP CRIB AWAY FROM OPEN FIRES AND OTHER HEAT SOURCES.

Crib Parts:

Headboard

Left Crib Side

Right Crib Side

Upper Footboard

Lower Footboard

Left Day Bed Cap

Right Day Bed Cap

Mattress Support

4x Feet

Allen Wrench

(J) Foot

(A) Headboard

(J) Foot

Step 1:

A. Align the Feet (J) with the bottom of the posts on the Headboard (A), and tighten the screws with the allen wrench. B. Align the Feet (J) with the bottom of the Lower Footboard (C), and tighten the screws with the allen wrench..

(A) Headboard

Mattress support holes should face the inside of the crib

Thread and tighten two bolts (both sides)

(E) Right Crib Side

(D) Left Crib Side

Step 2:

A. Line up the Crib Sides (D) and (E) with the Headboard (A). The mattress support holes on the crib sides should be facing the inside of the crib. B. Align the bolts with the holes in the headboard and tighten with the allen wrench. Repeat for the other side.

Thread and tighten

all four bolts

High Position

Middle Position

Low Position

(H) Mattress Support

Label reading “This Side Up” should be facing up

Step 3:

A. Flip the mattress support so the “This Side Up” label is facing up. If the label is missing, the correct orientation is with the springs at the top of the frame.

B. With a helper to hold it at the right height, align the bolts on the Mattress Support (H) with the holes on the crib sides and tighten with the allen wrench. There are three possible height positions. The support should start at the high position for newborns, then be moved lower as the child grows and becomes more mobile. Once the child is able to pull up to a standing position, the support must be set to its lowest position.

(B) Upper Footboard

Thread and tighten all three bolts (both sides)

Step 4:

A. Place the Lower Footboard (C) against the crib sides. B. Turn the two bottom bolts into the lower footboard holes, but don’t tighten them yet. C. Place the Upper Footboard (B) on top of the lower footboard. D. Turn the two upper bolts into the upper footboard holes, but don’t tighten them all the

way yet. Repeat for the other side. E. Once all the bolts are started, tighten them all with the allen wrench.

+ 15 hidden pages