Page 1
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF PRODUCT.
Failure to follow warnings and instructions could result in injury or death to your child.
Make sure rocker is fully assembled and secure before use.
Keep these instructions for future reference.
R02J-A 3/03
1
R02J-A
B
ABY’S
1ST JEEP® ROCKER INSTRUCTIONS
! !
WARNING
• STOP using rocker when your child is 36 months or weighs more than 45 lbs (20.41 kgs).
• To prevent injury from falls:
• NEVER leave your child unattended.
• NEVER use on any elevated surface.
•ALWAYSuse restraint until child is able to climb in and out of the chair unassisted.
• Use the upright position only when child can sit up unassisted.
• NEVER lift rock er while child is seated.
• DO NOT lift by to y bar.
• NEVER use rock er as a car seat;it will not protect your baby during an accident.
A
VOID STRANGULATION HAZARDS:
• DO NO T place items with a string around child’s neck (pacifier cords,hood strings,etc.).
• DO NOT allow strings to hang into bouncer, including blind cords or suspended toys other than
what is provided with this product.
• DO NOT use around pets or other children.
• DO NOT continue using infant rocker if it becomes bent,broken or if the cloth cover is
ripped or torn.
© 2003 Kolcraft®Enterprises,Inc. All rights reserved.
Frame
Toy Bar
Seat Pad
Infant Headrest
by
PARTS LIST:
Page 2
R02J-A 3/03
2
Step 1.
Insert a flat head
screwdriver tip into battery door
located underneath vibrator. Release
tab,and gently push tab back and
up to release.
Step 2. Insert “C” cell battery as
shown.
Step 3. Replace battery cover
making sure tabs snap securely
into place.
Step 4.
Slide button to “on” position to activate vibrating mechanism.
Step 5. Slide button to “off”
position to stop vibrating motion.
54
Remove battery before
storing the product for a
prolonged period of time.
CAUTION
! !
1
2
Step 1. To open frame,hold top
of frame and pull the wire lever until
rocker is open.
Step 2. Slip seat pad onto back of
frame making sure release handle fits
through opening.
Step 3. Zip the seat pad to secure
to frame.
1
TO INSTALL BATTERIES IN
VIBRATOR:
2
T O ASSEMBLE FRAME:
How To Assemble Y our Rocker
Page 3
R02J-A 3/03
Step 4.
Pull fabric over vibrator.
Step 5. Flip rocker over. Feed
straps through “D” ring and secure as
shown.
Step 1.
Lift red buttons on both
sides of toy bar and fasten onto frame
as shown.
NOTE: One side of toy bar can be
locked open when placing child into
rocker. Release one side of toy bar
and swing open as shown.
CAUTION: Mirror on toy bar
may have a colored piece of plastic film
for protection during production. This
film likely was removed. For your
child’s safety,please check the mirror
on the toy bar and remove any plastic
film you discover prior to use of this
rocker.
Step 2. Velcro head rest to seat
pad.
NOTE: Use head rest until child
can hold their head up unassisted.
3
3
TO INSTALL TOY BAR &
INFANT HEADREST:
Page 4
How to Properly Use Your New Rocker
4
R02J-A 3/03
Step 1. Place child in the seat.
Position restraint system between
legs.
Step 2. To fasten restraint system
buckle, push buckles together as
shown.
Step 3. To adjust restraint
system,loosen or tighten loop of
restraint to fit snugly around child’s
waist.
Step 4. To unsnap restraint
system buckle – press tabs.
When child is able to climb in and out
of the chair unassisted,you may store
the restraint system behind the seat.
Insert restraint through small slot in
the seat pad.
Secure both fasteners of restraint to
backside of rocker as shown.
Newborn Position
Adjust rocker into the fully supported recline position.
To adjust seat position,pull up on
wire lever and adjust seat back until it
is fully reclined and locks into place.
NOTE: Use head rest until child
can hold their head up unassisted.
IMPORTANT! Use the upright Toddler
position only when child can sit up
unassisted!
1
TO FASTEN RESTRAINT
SYSTEM:
2
NEWBORN ROCKER USE
POSITION:
Page 5
Remove toy bar completely and
adjust rocker to the up-most
position.
To adjust seat,pull up on wire lever
and adjust seat back to forward
position.
Stationary Feeding Position
Your rocker also has a stationary bar
which locks the chair for feeding
time.To use stationar y bar,rotate
until it is fully extended as shown.
Toddler Position
Infant Position
Adjust rocker into the semi-recline
position.
To adjust seat,pull up on wire lever
and adjust seat back to the middle
upright position.
IMPORTANT! Use the upright
Toddler position only when child
can sit up unassisted!
Step 1. Remove toy bar.
Step 2. Pull up on wire lever and
push seat forward until rocker is flat.
IMPORTANT! Use the upright
Toddler position only when child
can sit up unassisted!
5
R02J-A 3/03
3
INFANT ROCKER USE
POSITION:
4
TODDLER CHAIR USE
POSITION:
5
STORAGE:
Page 6
To contact the manufacturer directly:
Kolcraft®Enterprises,Inc. Consumer Service Depar tment
10832 NC Highway 211East
Aberdeen,NC 28315
1-800-453-7673 in U.S.& Canada, 1-910-944-9345 outside U.S. & Canada
Eastern Standard Time,8 am-5 pm
6
R02J-A 3/03
MODEL NUMBER:
D
ATE OF MANUFACTURE:
D
ATE OF PURCHASE:
Once in a while, we are less than perfect and one of our products
reaches a customer with a problem. In most cases, we can solve your
problem with replacement parts. Please contact us before you return
one of our products to the store.Once a product is returned, it
cannot be resold. The materials and the energy used to make it are
wasted.
Please fill in the information in the space provided and attach a copy of
your purchase receipt.You will need this information to obtain warranty service.
You can find the Model Number and Date of Manufacture on a sticker
located on the rocker leg.
Jeep®is a registered trademark of DaimlerChrysler Corporation,and is used under license by Kolcraft®. © DaimlerChr ysler Corporation 2003
KOLCRAFT®warrants this product to be free of defects in materials and workmanship, as follows: For a period of ONE YEAR from the date of purchase,
KOLCRAFT will repair or replace, at its option, the defective product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. KOLCRAFT SHALL NOT BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO
THE EXTENT REQUIRED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE DURATION OF THIS WARRANTY.
Some regions do not allow the exclusion or limitation of warranties set forth above,so the above exclusions may not apply to you. This warranty gives
you specific legal rights,and you may have other rights. We sincerely thank you for your purchase of this KOLCRAFT product.
For further information visit www.kolcraft.com
• To clean:Machine wash seat pad in cold water,gentle cycle. Do not use abrasive cleaners.Line dr y. Do not soak in water.
• Always store your Jeep®baby product in a clean dry place. If exposed to damp conditions,leave fully opened and in a warm environment. Dry off with a soft cloth. Storing a damp rocker will encourage mildew to form.
• Do not leave in the boot of a car.
• Avoid exposure to salt water/seat water,as this may encourage the formation of rust. If rocker is used in this environment,completely
clean your rocker afterwards to remove sand and salt from mechanisms and wheel assemblies.
• Should parts of your rocker become stiff,squeak or difficult to operate ensure dirt is not the cause.
• Clean metal parts with a damp cloth and wipe dry.
• Clean vinyl parts with mild soap and water solution.
• When storing rocker,never stack other items on top of it;this may damage the rocker.
• Periodically check for worn parts,loose screws,torn materials or stitching.
• Replace any damaged parts immediately.
LIMITED W ARRANTY
PERSONAL RECORD CARD
CARE / MAINTENANCE
SERVICE HOTLINE
Attention to manufacturing detail and strict quality control
ensures that this product meets the highest standards set by
Kolcraft Enterprises,Inc. If you encounter any problems or
need assistance please call our Customer Service /Warranty
Department.
Please direct any comments or questions to:
Born with Style
PO Box 789
Gladesville NSW 1675
Australia
Phone:1300 885 337 or 02 9816 3837
Email:warranty@bornwithstyle.com.au
Replacement parts provided by local distributor due to
accidental damage or misuse to product will be charged
accordingly.
Loading...