Kolcraft KF002 User Manual

Elan Crib Assembly Instructions

Instructions d'assemblage pour lit de bébé Elan

Instrucciones de montaje de la cuna Elan

Q020

WARNING

FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD

RESULT IN SERIOUS INJURY OR DEATH.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR

¢ FUTURE USE.

¢NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS

BECAUSE THEY CAN CAUSE SUFFOCATION.

¢TO REDUCE THE RISK OF SUDDEN INFANT DEATH SYNDROME (SIDS), PEDIATRICIANS

RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR BACKS TO SLEEP, UNLESS OTHERWISE ADVISED BY YOUR PHYSICIAN.

¢INFANTS CAN SUFFOCATE ON SOFT BEDDING. NEVER ADD A PILLOW OR COMFORTER.

NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.

STRANGULATION HAZARD

¢STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND

A CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.

¢TO HELP PREVENT STRANGULATION, TIGHTEN ALL FASTENERS. A CHILD CAN TRAP

PARTS OF THE BODY OR CLOTHING ON LOOSE FASTENERS.

¢DO NOT PLACE CRIB NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY

STRANGLE A CHILD.

FALL HAZARD

¢WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST

POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.

¢STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF

35 IN. (89 CM).

¢CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR OTHER FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER FASTENERS. DO NOT USE CRIB IF ANY PARTS ARE MISSING, DAMAGED, OR BROKEN. CONTACT KOLCRAFT ENTERPRISES, INC (www.kolcraft.com/customer-service/contact-kolcraft) FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.

¢IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS. ¢FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB. ¢INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS

TOO SMALL.

¢ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 IN. (69 CM) BY 51-5/8 IN.

(131 CM), WITH A THICKNESS NOT EXCEEDING 6 IN. (15 CM). THE DIMENSIONS OF THE MATTRESS SHOULD BE TAKEN FROM SEAM TO SEAM.

¢PREVENT BURNS. KEEP CRIB AWAY FROM OPEN FIRES AND OTHER HEAT SOURCES.

WARNING

For conversion to a toddler bed or daybed, the toddler/daybed conversion kit manufactured by Kolcraft MUST BE USED. See Instructions.

Crib Parts:

2x Ends

Mattress Support

2x Sides

Allen Wrench

(B) Side

(A) End

Step 1:

A. Align a Side (B) with the Ends (A). There is no top or bottom to the side, it can be used in

either direction. B. Tighten the screws with the allen wrench.

Thread and tighten

all four screws

High Position

Middle Position

Low Position

Label reading “This Side Up” should be facing up

Step 2:

A. Flip the mattress support so the “This Side Up” label is facing up. If the label is missing,

the correct orientation is with the springs at the top of the frame.

B. With a helper to hold it at the right height, align the screws on the Mattress Support (C) with the holes on the crib sides and tighten with the allen wrench. There are three possible height positions. The support should start at the high position for newborns, then be moved lower as the child grows and becomes more mobile. Once the child is able to pull up to a standing position, the support must be set to its lowest position.

+ 11 hidden pages