Kokido Telsa 10, EV10 User Manual
RECHARGEABLE CORDLESS CLEANER
USER MANUAL
ASPIRATEUR RECHARGEABLE SANS FIL
MANUEL D’EMPLOI
ASPIRADORA INALÁMBRICA RECARGABLE
MANUAL DE USUARIO
Table Of Contents
PARTS DIAGRAM
SAFETY WARNINGS & INSTRUCTIONS
GETTING STARTED
Charging The Battery
Set-Up Before Use
Pole connector assembly P.8
Brush assembly P.9
Pole assembly P.9
Telescopic pole (not included) assembly P.9
OPERATION
EMPTYING THE FILTER
MAINTENANCE & STORAGE
P.4
P.5
P.7
P.7
P.8
P.10
P.11
P.12
BATTERY DISPOSAL
How to remove the battery pack
TROUBLESHOOTING
P.12
P.13
P.14
Remark: Product/parts photos in this manual are for demonstration only.
Product/parts in photos may vary with the model purchased.
1
Table des matières
DIAGRAMME DES PIÈCES
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS
DÉBUT DES OPÉRATIONS
Chargement de la batterie
Réglage avant l’utilisation
Montage du connecteur de manche
Montage de la brosse
Montage du manche
Montage du manche télescopique (non inclus)
FONCTIONNEMENT
VIDER LE FILTRE
P.15
P.16
P.18
P.18
P.20
P.20
P.20
P.20
P.21
P.21
P.22
MAINTENANCE ET STOCKAGE
ÉLIMINATION DES BATTERIES
Comment retirer le bloc de batteries
REPÉRAGE DE PANNES
P.23
P.24
P.25
P.26
Remarque : Les photos du produit/des pièces dans ce manuel sont
présentées uniquement à titre d’exemple. Le produit/les pièces peuvent
varier selon le modèle acheté.
2
Indice
DIAGRAMA DE LAS PARTES
AVISOS E INSTRUCCIONES DE SEGURIDAD
PRIMEROS PASOS
Carga de la batería
Montaje previo al uso
Montaje del conector de pértiga P.32
Montaje del cepillo P.32
Montaje de la pértiga P.32
Montaje de la pértiga telescópica (no incluido) P.32
FUNCIONAMIENTO
VACIADO DEL FILTRO
MANTENIMIENTO Y ALMACENAMIENTO
P.27
P.28
P.30
P.30
P.32
P.33
P.34
P.35
ELIMINACIÓN DE LA BATERÍA
Cómo retirar el paquete de baterías
RESOLUCIÓN DE PROBLEMAS
P.36
P.36
P.38
Observación: Las fotos de producto/piezas de este manual son sólo para
demostración. Producto / piezas en las fotografías pueden variar según el
modelo adquirido.
3
PARTS DIAGRAM
1
Main body 7 Pole connector
2
Filter bag 8 Pole sections
3
Front cover 9 Charger base
4
Brush 10 Charging contact plate
5
Nozzle flap 11 Power ON/OFF button
6 Wheel
Battery: Rechargeable Li-ion battery pack, 2000mAH, 7.4V, 14.8Wh
Charging voltage : 8.4V DC, 1.0 A
Motor: 7.2V DC
4
SAFETY WARNINGS & INSTRUCTIONS
Read and follow all instructions in this manual and on the equipment. Failure to do so
could result in severe or fatal injuries.
WARNING!
- This is not a TOY. Children should be kept out of reach from this pool vacuum and
its accessories.
- Never allow children to operate this product.
- This pool vacuum is not intended for use by someone with reduced physical,
sensory or mental capabilities, or a lack of experience and knowledge unless they
have been given instructions concerning the appliance and are under supervision
of the person responsible for their safety.
- Make sure the pool vacuum is fully immersed in the water before operation. The
minimum water level required to operate the device must reach above the power
button of the pool vacuum when it is held in a vertical position. Operating the pool
vacuum when it is not immersed in the water correctly could damage the unit and
void the warranty as a result.
- Maximum operating depth in water is 2 meters (6.5 ft).
- Maximum water temperature: 5˚C (41˚F) –35˚C (95˚F)
- DO NOT use power extension cords.
- Connect the external adaptor to a power source through a residential current
device (RCD). If in doubt, consult a qualified professional electrician.
- Do not use this pool vacuum if any damage is detected.
- Replace damaged parts as soon as possible. Only use parts certified by the
distributor or manufacturer.
- Turn off the power, disconnect the external adaptor from the power source, and
unplug the external adaptor from the charging base before detaching the pool
vacuum from the charging base.
- Disconnect the pool vacuum from the supply mains prior to carrying out user
maintenance such as cleaning the filter.
- Detach the pool vacuum from the charging base and make sure the pool vacuum
is OFF before servicing the product.
- Battery installed is a rechargeable Li-ion battery pack. Never attempt to replace
the battery pack.
- The pool vacuum is only to be used with the external adaptor delivered with this
product.
- You should not operate this pool vacuum when people/pets are present in the
water.
- DO NOT use this pool vacuum without an intact filter bag in place, as your
warranty will be voided as a result.
- Suction entrapment hazard: This pool vacuum generates suction. Do not allow
hair, body, or any loose parts of your clothing to make contact with the suction
hole of the pool vacuum during its operation.
- Never insert body parts, clothing or other objects into the openings and moving
parts of the pool vacuum.
- DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or in the presence of explosive or flammable
fumes.
- Never attempt in any way to disassemble this pool vacuum.
5
- Under no circumstances should you attempt to disassemble the pool vacuum and
replace the impeller, motor, and battery by yourself.
- Never insert any object to touch the impeller.
- External adaptor and charging base:
For indoor use only.
Never use the external adaptor and charging base for anything other than
charging the battery of the pool vacuum that is supplied in the same pack.
The external adaptor and charging base should not be used outdoors, nor
exposed to rain, humidity, any liquid or heat.
Keep the external adaptor and charging base out of reach of children.
Never use the external adaptor and charging base if any damage is
detected.
DO NOT handle the external adaptor and charging base with wet hands.
DO NOT handle the pool vacuum, external adaptor, and charging base
while charging with wet hands and without shoes.
Keep the external adaptor disconnected from power when it is not in use.
Never attempt to open the external adaptor and charging base.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or an equally-qualified person in order to prevent hazards of
any kind.
Make sure the pool vacuum and the charging base are completely dry
before charging.
CAUTION!
- This pool vacuum is designed for underwater use only; it is not an
all-purpose vacuum cleaner. DO NOT attempt to use it to clean anything
other than your pool / spa.
- Use only original accessories delivered with this product.
- DO NOT use this pool vacuum right after pool-shocking. It is
recommended to leave the pool circulating for at least 24-48 hours.
- It is not recommended to use this pool vacuum with another pool
vacuum/cleaner simultaneously.
- Avoid picking up hard, sharp objects with this product. They may
damage the pool vacuum and filter.
- Exercise caution when cleaning pool stairs.
- Only use the charging base for its intended purpose as outlined in this
manual.
- To avoid damaging the external adaptor and the cord, do not carry the
pool vacuum by the cord or pull the cord to disconnect it from the power
source and product.
- Charge the pool vacuum indoor in a clean, dry area with good ventilation
and an ambient temperature between 5˚C (41˚F) and 35˚C (95˚F).
- DO NOT leave the pool vacuum charged for over 20 hours.
- If the pool vacuum will not be used for an extended period, detach it from
the charging base and use a damp cloth to clean and dry the pool
vacuum and accessories. Make sure to charge the pool vacuum
completely before it is stored. Store in a well-ventilated area away from
sunlight, heat, ignition sources, pool chemicals, and children. Never
6
leave the pool vacuum plugged in for long-term storage. Recharge the
pool vacuum every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.
GETTING STARTED
IMPORTANT NOTE: Fully charge the pool vacuum before using it for the first time.
Charging the battery
WARNING!
Charging must be done indoors, in a well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C (41˚F)
and 35˚C (95˚F).
Never use the external adaptor and charging base if any damage is detected.
Use only the original external adaptor provided.
Make sure the pool vacuum and the charging base are clean and dry before set-up.
1. Place the unit on a flat surface. Insert and slide the hook of the charging base into
the notch on the end of the main body unit it stops. Make sure the contact plates
are properly in contact.
2. Plug the female jack of the external adaptor into the charging port at the end of the
charging base.
WARNING!
DO NOT handle the pool vacuum, external adaptor and charging base while it is
charging with wet hands and without shoes.
Connect the external adaptor to the power source through a residential current
device (RCD).
7
Charge the pool vacuum with the original external adaptor provided.
DO NOT use power extension cords.
Fully charge the battery before first use.
Charging must be done indoors, in a dry & well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C (41˚F)
and 35˚C (95˚F).
Always disconnect the external adaptor from the power source when charging is
complete.
Do not leave the pool vacuum in charge for over 20 hours.
Immediately turn the power off and disconnect the external adaptor from the power
source if you detect any of the following conditions:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
1. Make sure that the pool vacuum is turned off prior to charging.
2. Connect the external adaptor to the power source. Once the pool vacuum begins
charging, the indicator light on the external adaptor will turn red. Normally, it takes
about 4- 5 hours to reach a full charge. The indicator light will turn green when the
pool vacuum is almost fully charged.
Note: If the motor is generating noise, immediately turn off the device by pressing the
ON/OFF button. Otherwise, it could potentially lead to failure of the shaft seals / motor,
and the warranty will be voided as a result.
Note: Charge the pool vacuum completely (about 4-5 hours) prior to the first use.
3. When charging is complete, disconnect the external adaptor from the power source
and unplug the jack from the charging base.
4. Detach the charger base from the pool vacuum.
Normally, the pool vacuum can be operated up to 45 minutes on a full charge
(charged for 4-5 hours)
Note: Clean the filter regularly. Too much debris inside the filter will increase burden
to the motor operation and then shorten the operating duration.
FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a
limited life and will gradually lose its capacity to hold a charge. Therefore, running
time of the pool vacuum will gradually reduce through repeated charging and
discharging in operation.
NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.
Set-Up Before Use
Pole connector assembly
Press down the side pins of the connector and insert it inside the main body. Turn the
connector in either direction until the pin is secured in the hole, as shown in the
diagram.
8
Brush assembly
Align and push the brush into the notch on the front cover.
Pole assembly
Select the tube section with a threaded tip at the end. Insert and the threaded tip of
the pole section inside the pole connector and turn it clockwise to screw it inside.
Finish the assembly by inserting the grooved ends of the following section tubes in
the round ends of the remaining section tubes. The section with the grip is the last
section to be assembled.
Telescopic pole assembly
Note: V-clip is installed inside the pole connector for the purpose of securing the
telescopic pole (not included) in position. Slide the telescopic pole onto the pole
connector. Press on the side pins of the connector and slide the telescopic pole
further until the pins are secured inside the holes of the pole.
To release the telescopic pole, press down the side tabs simultaneously and pull out
the pole.
9
OPERATION
WARNING!
Do not use the pool vacuum if any damage is detected.
Oil stain could occur due to possible leakage of lubricants applied to the O-ring.
Do not operate this pool vacuum if there are people/pets present in the water.
Make sure the pool vacuum is fully immersed in the water before initiating operation.
The minimum water level required to operate the device must reach above the
power button of the pool vacuum when it is held in a vertical position. Operating the
pool vacuum when not immersed in the water correctly can damage the unit and
the warranty will be voided as a result.
Maximum operating depth in water is 2 meters (6.5 ft).
Maximum water temperature: 5˚C (41˚F) –35˚C (95˚F)
DO NOT use the pool vacuum without an intact filter bag in place. Using your pool
vacuum without an intact filter bag in place will VOID your warranty.
Suction entrapment hazard: This pool vacuum generates suction. Do not allow hair,
body or any loose parts of your clothing to make contact with the suction mouth of
the pool vacuum during its operation.
Never insert body parts, clothing or other objects into the openings and moving
parts.
DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or operate in the presence of explosive or
flammable fumes.
DO NOT cover the side slot of the cleaner body during operation. The
impeller/motor may be damaged as a result.
Never insert any object to touch the impeller.
CAUTION
Use only original accessories delivered with this product.
DO NOT use this pool vacuum immediately after pool-shocking. It is recommended
to leave the pool circulating for at least 24-48 hours.
It is not recommended to use this pool vacuum with another pool vacuum/cleaner
simultaneously.
DO NOT leave the pool vacuum in the water when it is not in use or when battery is
low as water leakage may occur.
1) Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in
water and press the power button to initiate operation.
CAUTION! Make sure the pool vacuum is always facing downwards when it is placed
into the pool. Otherwise it may bend the pole connector and damage it during the
process.
2) To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing
it downwards in order to allow water to escape from the outlet valve. Water is going to
escape via the handle / pole connector and draining holes inside the handle chamber
on the rear body.
CAUTION! Make sure the pool vacuum is always facing downwards when it is
removed from the pool. Otherwise, the pole connector may be bent and damage the
pool vacuum in the process.
10
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any
detergent.
EMPTYING THE FILTER
WARNING! Using the pool vacuum without a filter bag in place will VOID your
warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter bag before and
after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the
power source and detach the pool vacuum from the charger base.
Emptying filter bag
1. Place the pool vacuum on a stable surface.
2. Hold the front cover and pull on the rib (on cover bottom) to detach the front cover
from the main body. Take the filter bag out of the cleaner.
CAUTION! Replace the damaged filter bag immediately before the next operation.
3. Clean out the debris and rinse the filter bag with splashing water. If brushing is
deemed necessary, use only a soft brush to clean it gently and carefully.
4. Reverse the previous steps to re-assemble the filter bag and then the front cover.
Make sure the front cover is well secured on the main opening body and that no gaps
are visible before the next operation.
11
Loading...