Kohler Renew 76881T-E, Renew 76882T-E Installation Instructions Manual

SERVICE PARTS

RENEW

INSTALLATION INSTRUCTIONS

RENEW

1061576

1219396**

76881T-E Slide Shower-Geometric
76882T-E Slide Shower-Organic

1208178

23096

1208176**

1195838**

1240266

1030624

76881T-E:1236560**

76882T-E:1236561**

76881T-E Slide Shower-Geometric
76882T-E Slide Shower-Organic

BEFORE YOU BEGIN

All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.

Please leave these instructions for the consumer. They contain important information.

NOTES:

1. Observe local plumbing codes.

2. An inline water filter must be used with this product.

3. The highest working pressure for handshower is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure reducer
is needed. The highest water and environment temperature is 60°C. Please keep handshower, showerhead and
the shower arm away from heater, or it may become damaged and cause injury to the user.

4. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.

ROUGH-IN DIMENSIONS

75

60

G1/2˝

Ø110

1081607

1208177**

1208178

1061576

23096

**Color code must be specified when ordering.

1128483

1194751**

1248781**

1269272**

58

560~660

700~800

1500

G1/2˝

58

51

G1/2˝

Only for 76881T-E

Ø110

G1/2˝

Only for 76882T-E

G1/2˝

243

249

260

252

59

38

44

G1/2˝

1273668-AN2-A 4

1273668-AN2-A 1

INSTALLATION

How to Install the Connection Kit

7

8

560~660

13

How to Install the Slide Bar

1

2

3

Decide on a suitable position for the slide bar avoiding
buried cables and pipes in the wall.

12~20mm

16

Before installation, installer must provide G1/2″ supply
fitting(13). Ensure it extend 12~20mm beyond the
finished wall.

Apply tape or thread sealant to G1/2″ threads of the
supply fitting. Apply a ring of plumber putty or other
sealants around the underside of the connection

kit(16). Install the connection kit onto the supply fitting.
Drill two holes at the proper height on the finished wall
according to the rough-in dimensions and should
match the anchors(1).

15

14

Adjust the connection kit and make sure the outlet(14)

and drain notch(15) of the escutcheon downwards.

Remove any excess putty.

①

Put anchors into the holes. Install the upper and under
base(2) with screws(3) in the wall.

How to Install the Handshower and Hose

Flush both water supplies for about one minute before

10

Place the bar(5) into the under slide bar body(6).
Install the screw(7), tighten them by hex wrench(8).

17

18

the handshower(18) is installed. Attach the

handshower to shower hose(17). NOTE: Don’t over

tighten.

Connect another end of shower hose to the outlet(14)
Slide the handshower holder(4) onto the bar. The

5

height of handshower holder can be adjusted by
pressing the pinch cock(9) and sliding up and down.

of the connection.

Hang the handshower in the bracket(4).
Adjust it to the proper position.

4
9

Tighten the screw(7) to secure upper slide bar
body(10) by hex wrench according to the rough-in

7

6

12

2

11

Drain notch

dimensions. Make sure the directions of the upper and
under slide bar body are consistent.

②

Slide the bracket escutcheons(11) onto the bases(2),
confirm the drain notch of the escutcheon is pointed
down. Install the whole slide bar onto the bases.

Tighten the screws(12) by hex wrench to secure the
slide bar.

How to Operate the Handshower

Rotate the knob of the handshower to change the water
flow.

How to Maintain the Handshower

Any debris or mineral build-up may cause the flow
stream to become distorted or reduce the flow rate. To
remove the debris or mineral build-up, run water
through the handshower, firmly press or rub your finger
back and forth across the rubber nozzles.

CLEANING INSTRUCTIONS

11

Drain
notch

12

③

1273668-AN2-A 2

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings.

1273668-AN2-A 3