SERVICE PARTS
INSTALLATION INSTRUCTIONS
RENEWRENEW
76367T Multifunction Handshower With Hose & Bracket-Organic
76368T Multifunction Handshower With Hose & Bracket-Geometric
76368T:1236560**
1240266
1030624
77420
76367T:1236561**
1240266
1030624
77420
76367T Multifunction Handshower With Hose & Bracket-Organic
76368T Multifunction Handshower With Hose & Bracket-Geometric
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. The highest working pressure for handshower is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure reducer
is needed. The highest water and environment temperature is 60°C. Please keep handshower, shower head and
the shower arm away from heater, or it may become damaged and cause injury to the user.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
ROUGH-IN DIMENSIONS
G1/2˝
1061576
1208174**
1208172
1081607
1284563**
1248781**
Ø110
51
243
58
28
Ø7
33
85
252
G1/2˝
Ø110
1500
249
260
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
1266736-2A-B 4
G1/2˝
G1/2˝
76367T 76368T
1266736-2A-B 1
INSTALLATION
1
How to Install the Bracket
Determine a suitable location on the
2
3
4
6
5
①
finished wall to install the bracket, make
sure it should avoid buried cables and
pipes in the wall.
Mark bracket base mounting hole
locations on the wall according to the
dimension. Drill two holes in the finished
wall, the holes should match the
anchors(1) and be vertically. Install the
anchors. Tighten screws(3) to fix bracket
base(2) on the finished wall. NOTE: The
bracket base direction as shown.
Loosen the screw(6) in the bottom of the
bracket(4) with the hex wrench(5), make
the bracket can be installed. Apply a ring
of plumber putty or other sealants around
the underside of the bracket. Put the
bracket onto the bracket base and lock
them by screw and hex wrench.
Remove any excess putty.
How to Operate the Handshower
Rotate the knob of the handshower to
change the water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow stream to
become distorted or reduce the flow rate. To remove the debris or
mineral build-up, run water through the hand shower, firmly press or
rub your finger back and forth across the rubber nozzles.
Remove and clean the screen washer.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
How to Install the Handshower
and Hose
Flush both water supply for about one
minute before the handshower(7) is
installed.
7
9
8
10
11
Install check valve(8) and regulator(9)
into the handshower inlet if needed.
Put the screen washer(10) into the
shower hose(11) connector. Connect the
handshower to shower hose. NOTE:
Don’t over tighten.
②
Hang the handshower on the shower
bracket. Connect another end of shower
hose to the water supply.
1266736-2A-B 2
1266736-2A-B 3
Loading...