Kohler REACH K-3856T-S, REACH K-3856T-B, REACH K-4088T, REACH K-4087T Installation Instructions Manual
REACH
INSTALLATION INSTRUCTIONS
VITREOUS CHINA ONE-PIECE TOILET
K-3856T-S/K-3856T-B
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning, and
warranty information -.please leave instructions for the
consumer
ORDERING INFORMATION
REACH One-piece Toilet
Includes
REACH One-piece Toilet
Includes
REACH Quiet-Close
(Hidden Hinge Base)
REACH
(Hidden Hinge Base)
.........................................K-3856T-S
Toilet Seat
..................................K-4087T
.........................................K-3856T-B
Toilet Seat
..................................K-4088T
NOTES
Observe all local plumbing and building codes.
·
Shut off the water supply.
·
Seat post holes are on 140mm (5-1/2") centers.
·
Ensure that the new drain has the correct roughing-in
·
dimension. This toilet has a 305mm (12") roughing-in
dimension. .
Closet flange must be 305mm (12") on-center from wall.
·
Carefully inspect the new fixture for any sign of damage.
·
For new construction, refer to the dimensions in
·
installation step
Fixture dimensions are nominal and conform to tolerances
·
established by ASME Standards (A112.19.2-2008).
See Roughing-in
for locating the shut-off valve.
·
·
·
()
()
·
·
·
·
·
·
·
·
2008)
-
.......................................................K-3856T-S
.............................................................K-4087T
........................................................K-3856T-B
.............................................................K-4088T
140mm
305mm(
)
305mm
ASME (A112.19.2-
WARNING: Risk of personal injury or product
damage
Vitreous china can break and chip if you overtighten
bolts and nuts.
WARNING: Risk of external leakage
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten one turn
past finger tight .
: Handle vitreous china products very carefully.
. The fill valve
1182020-T01-A
-1-
528137
, 2011
Copyright Kohler China Ltd., 2011
TOOLS AND MATERIALS REQUIRED (Not
supplied)
254mm (10") adjustable wrench
·
305mm (12") pipe wrench
·
Metal file (file cut)
·
Tape measure
·
Tubing cutter
·
Level
·
Hacksaw
·
Putty knife
·
Screwdriver
·
Toilet gasket (wax seal)
·
Toilet installation flange
·
Toilet T-bolts (2), 8mm (5/16") diameter
·
Toilet supply shut-off valve, 10mm(3/8 ) recommended
·
"
·
·
·
·
·
·
·
·
·
·
·
·
·
254mm
305mm
8mm T 2
10mm
NOTICE:
If the existing toilet does not have a supply shut-off
valve below the tank, install one before installing the new
toilet.
* Flexible hose are recommended to connect the supply line
to the fill valve. If you use a rigid connection, take care not to
apply side forces to the bottom of the fill valve.
Reference Value
366
728
355
*
Unit: mm
573
220
:
217
Finished
Wall
305
1182020-T01-A
715
Supply
390
140
135
Kohler reserves the right to change marked dimensions without prior notice.
-2-
INSTALLATION
1 Install or relocate the supply and outlet as necessary to comform to the roughing-in dimensions.
715
Supply
140
135
Important: Toilet must have 305mm minimum rough-in to
install properly.
305mm
2 If replacing a toilet, remove the old wax.
3 Insert new T-bolts.
If installation of the new toilet is delayed, temporarily cover
the closet flange hole with a rag.
T
NOTICE:
cements to install this toilet. The expansion of cement due
to a rise in temperature may make the toilet crack or cause
damage. Kohler is not responsible for any damage caused
by installation with the use of cement.
Do not use white cement or high lime content
T-Bolts
T
Closet
Flange
1182020-T01-A
-3-
Loading...