Kohler Purist 14434, Purist 14402, Purist 14404 Installation Instructions Manual

SERVICE PARTS

14402 SINGLE HOLE LAVATORY FAUCET
14404 SINGLE HOLE TALL LAVATORY FAUCET
14434 SINGLE HOLE BIDET FAUCET

1032012**
Plug Button Kit

76713
Screw

1048356**
Sculpted Lever
Handle Kit

1026689**
Bonnet

1056867**
Nut

1014338
Valve

1049039**
Straight Lever
Handle Kit

1032012**
Plug Button Kit

76713
Screw

Single Lever/Single Control

880008**
Stopper

1080817
O-ring

880406
Washer

834753**
Pop Up Drain

(Only for 14402-4/4A
& 14434-4/4A)

880037
Link Kit

INSTALLATION INSTRUCTIONS

Single Hole Lavatory/Bidet Faucet

14402 SINGLE HOLE LAVATORY FAUCET
14404 SINGLE HOLE TALL LAVATORY FAUCET
14434 SINGLE HOLE BIDET FAUCET

BEFORE YOU BEGIN

All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.

Please leave these instructions for the consumer. They contain important information.

NOTES:

1. Flush the water supply pipes thoroughly to remove debris.

2. Inspect the supply tubing for damage. Replace as necessary.

3. If possible install faucet and drain before installing lavatory or bidet.

HANDLE OPERATION

Lift the handle gently. Turn left for hot water, right for cold water.

ROUGH-IN DIMENSIONS

1077946**
Areator
1069787**

834754
Hose
1024405(Only for India)

**Color code must be specified when ordering

(Only for Thailand)

1077946**
Areator
1069787**

(Only for Thailand)

1049041
Washer

1049040
Stud

836664
Mounting
Hardware

1077947**
Areator
1069788**

1023123**
Lift Knob

(Not for 14402-4ND/4AND
& 14404-4/4A)

21220**
Lift Rod

(Not for 14402-4ND/4AND
& 14404-4/4A)

1095926**
Click Drain

(Only for 14404-4/4A)

(Only for Thailand)

102888**
Stopper

1102889
Washer

1102892
Piston Kit

14402-4/14404-4/14434-4

Sculpted Level Handle

35°

159

Ø32-Ø35

Max. 40

350(450 for India)

G1/2˝

308

165

Ø32-Ø35

G1/2˝

35°

139

Max. 50

360(460 for India)

66

Ø32-Ø35

14404 14402 14434

14402-4A/14402-4A/14402-4A

Straight Level Handle

198

109

Max. 50

G1/2˝

198

70

360(460 for India)

176.5

Ø56

Ø42

173~185

101

Ø31.75

Only for 14404-4/4A

Ø54

Ø36.5

108

97.5

Ø31.75

Only for 14434-4/4A

1049889-2A-B 4

1049889-2A-B 1

INSTALLATION

How To Install The Lift Rod Assy
(Not For 14402-4ND/4AND 14404-4/4A)

Unscrew the lift rod knob(1) from the lift rod(2). Insert the lift rod into the hole from
underside of the faucet until the groove of the faucet. Screw the lift rod knob to the
lift rod, tightened by hand．

How To Install The Faucet

Install the stud(3) into the faucet body(6). Put the washer(4) into the bottom of body
through the flexible hoses(5) and the stud. Insert hoses and stud into the hole of
lavatory or bidet. Position the faucet. From underside of the lavatory or bidet, fit the
bracket(7) and washer(8) on the stud. Secure the faucet by tightening nut(9).

Attach the hoses to water supplies. When facing front of faucet, the left hose is hot
water, the right hose is cold water.

Take off ‘V’-clip(26) and the retaining nut(27). Fit the plastic washer(41) and
retaining nut onto the ball lever rod(29). Insert the ball lever assembly into the drain

26

27

lever hole(22) and through the stopper hole. Tighten the retaining nut.

28

1

2

Be sure that the ball lever rod points to the back of the bidet, tighten the locknut.

NOTE: Do not reposition the drain after the locknut is tightened, or you may break

29

the putty seal. Remove any excess putty.

2

Slide lift rod(2) into the hole on link(31). According to the lift rod length, bend the
link. Connect the link onto ball lever rod with ‘V’ clip(26). Position the lift rod, ensure

30

the distance between the lift knob and the faucet body is about 10mm.

31

6

4

5

3

7
8

Push the ball lever rod(29) down to the open position. Tighten thumb screw(30).

Connect the tailpiece to the trap. The tailpiece should extend 25mm to 50mm into
the trap.

26

29

How To Install The Drain
(For 14404-4/4A)

Remove the locknut(15), plastic washer(14), rubber gasket(13) and tailpiece(12)
from the drain body. Supply enough tape or sealant to tailpiece thread. Reinstall
the tailpiece. Insert the drain body into the lavatory. Put the rubber gasket (Tapered
side up), plastic washer and locknut back to the drain body in turn. Tighten the
locknut.

Note: If needed, apply a ring of plumbers putty or other sealants around the
underside of the drain flange(10), instead of using rubber washer(11).

Do not reposition the drain after the locknut is tightened, or you may break the
putty or sealant seal. Remove any excess putty or sealant seal.

How To Install The Drain
(For 14402-4/4A 14434-4/4A)

Uninstall the stopper(16), drain flange(18) and washer(19) from drain body(24).
Slide washer onto the underside of the drain flange. Uninstall the tailpiece(25) from
the drain body. Supply enough tape or sealant to tailpiece thread. Reinstall the
tailpiece. Insert the drain body with gasket(20), steel washer(21) and locknut(23)
into the lavatory or bidet from underside, with the drain lever hole(22) facing the
rear.

NOTE: If necessary, apply a ring of plumbers putty around the underside of the
drain flange, instead of using washer(19).

Thread the drain flange onto the drain body. Hand tighten the locknut from the
underside of the lavatory or bidet. Place stopper into drain body, aligning the flat
side of stopper hole(17) with the drain lever hole(22).

16

17

18

19

20

22

25

9

10

11

Drain Body

12

13

14

15

Apply Plumbers Putty

涂油灰

21

23

24

INSTALLATION CHECKOUT

Ensure all coupling nuts are tightened. Ensure that handle is in the off position.

Open the drain and turn on the main water supply. Check for leaks and repair
as required.

Remove aerator assembly(32). Turn on the tap. Run hot and cold water
through spout for about one minute to remove any debris. Check for leaks at
this time. Remove any debris from aerator assembly. Shut off the tap. Reinstall

32

aerator assembly.

CLEANING INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a clean
soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings.

1049889-2A-B 2

1049889-2A-B 3