Page 1
62" FREESTANDING BUBBLEMASSAGE™ BATH WITH BASK
Features
•
Slotted overflow for maximum bathing depth
•
Integral lumbar support
•
Molded armrests for extra comfort
•
Airjets release thousands of bubbles that surround, support and
massage the body
•
Variable-speed blower lets you adjust the airjet massage to 18
levels
•
Immediate and manual purge cycles remove residual water
from air channels after use
•
Bask™ Heated Surface provides soothing warmth on your back
and neck
•
Three heat settings allow you to customize the surface
temperature
•
Lighted keypad controls
•
Textured Bottom Surface
•
Two-piece design
•
61-3/4" (1568 mm) x 31-3/4" (806mm) x 22" (559 mm)
•
End Drain Placement
•
Requires 120V electrical service
Material
•
Exocrylic
Hydrotherapy
•
BubbleMassage
Installation
•
Freestanding Bath
•
Requires K-7271 or K-7272 Clearflo slotted overflow bath drain
(sold separately).
™
ARCHER
HEATED SURFACE
K-2593-GW
Codes/Standards
ASME A112.19.7/CSA B45.10
CSA B45.5/IAPMO Z124
UL 1795
CARB P2
See website for detailed warranty information.
Available Color/Finishes
Color tiles intended for reference only.
DescriptionCodeColor
White0
Biscuit96
Almond47
DuneNY
SandbarG9
®
™
Required Accessories
K-7271 Slotted Overflow Bath Drain
or
K-7272 Slotted Overflow Bath Drain
USA/Canada: 1-800-4KOHLER (1-800-456-4537)
www.kohler.com
2-18-2015 03:24
Page 2
No change in measurements if connected
ARCHER
62" FREESTANDING BUBBLEMASSAGE™ BATH WITH BASK
HEATED SURFACE
K-2593-GW
®
™
Required Electrical Service
One dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device
(RCD).
120 V, 15 A, 60 Hz, 300 WBlower, Heated
Surface:
Technical Information
All product dimensions are nominal.
FreestandingInstallation:
ReversibleDrain location:
45-1/8" x 19-11/16" (1147 mm x 500 mm)Basin area, bottom:
52-3/4" x 25-5/16" (1339 mm x 643 mm)Basin area, top:
100 lbs (45.4 kg)Weight:
44.2 lbs/ft² (215.8 kg/m²)Minimum floor load:
15-1/16" (383 mm)Water depth:
58 gal (219.6 L)Water capacity:
Electrical rating:
Blower: 120 V, 10 A, 60 Hz, 300 W
Heated Surface: 120 V, 0.5 A, 60 Hz, 65
W
VariablePump speed:
3-speedPump speed:
Notes
Measure your actual product for roughing-in
details.
Install this product in accordance with the
installation instructions.
Locate a GFCI-protected 120 V, 15 A, grounded
duplex electrical outlet within 24" (610 mm) of the
bath junction box. A 40" (1016 mm) cable is
included.
Locate the outlet behind the bath and within 24"
(610 mm) of the blower motor.
Remote blower installation kit K-1446 is available
for relocating the blower.
NOTICE: Do not support the load weight of the
bath by the rim.
NOTICE: Confirm adequate support for rim-mount
faucet. Using faucets as a means of support are
not appropriate or safe for this installation.
The hot water supply should be 70% of the
capacity of the bath or greater. Installations will
vary.
USA/Canada: 1-800-4KOHLER (1-800-456-4537)
www.kohler.com
2-18-2015 03:24
Loading...