Page 1
BANCROFT
®
Features
Acrylic
•
TM heated lumbar support with three temperature
Bask
•
settings
Slotted overflow for maximum bathing depth
•
120 BubbleMassage
•
Comfort Depth
•
step-over height
Blower motor with 300 W heater and electronic user
•
control
Molded lumbar support for comfort
•
Integral apron with removable access panel
•
Integral tile flange
•
3-wall alcove installation
•
Left or right drain
•
60″ (1524 mm) x 32″ (813 mm) x 21-1/4″ (540 mm)
•
TM airjets
design offers a 19″ (483 mm)
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
CSA B45.5/IAPMO Z124
•
ASTM E162
•
ASTM E662
•
ASME A112.19.7/CSA B45.10
•
UL 1795
•
Specified Model
5’ BUBBLEMASSAGETM BATH WITH
BASKTM HEATED SURFACE
K-1151-GLAW
ALSO K-1151-GRAW
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
NA: None applicable
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1151-GLAW 5’ BubbleMassage bath with Bask heated surface – left drain (shown) ❑ 0 ❑ Other_____
K-1151-GRAW 5’ BubbleMassage bath with Bask heated surface – right drain ❑ 0 ❑ Other_____
Recommended Accessories
K-1446 Remote blower installation kit NA
K-11677 Swiftflo
Optional Accessories
K-9497 2-1/2″ (64 mm) metal finish keypad trim ❑ CP ❑ Other_____
TM adjustable trip lever drain ❑ CP ❑ Other_____
Product Specification
The acrylic BubbleMassage bath shall be 60″ (1524 mm) in length, 32″ (813 mm) in width, and 21-1/4″ (540 mm) in height. Bath
shall have a blower motor with 300 W heater and electronic user control, and 120 BubbleMassage airjets. Bath shall feature
Bask heated lumbar support with three temperature settings. Bath shall have left or right drain. Bath shall have slotted overflow
for maximum bathing depth. Bath shall have molded lumbar support for comfort, integral apron with removable access panel,
and integral tile flange. Bath shall feature Comfort Depth design, which offers a 19″ (483 mm) step-over height. Bath shall be
for 3-wall alcove installation. BubbleMassage bath shall be Kohler Model K-1151-____-____.
Page 1 of 2
1201685-4-
B
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
BANCROFT
®
Technical Information
Required Electrical Service
Fixture*:
Bathing well:
Basin area, bottom 45″ (1143 mm) x 22″ (559 mm)
Basin area, top 54″ (1372 mm) x 25″ (635 mm)
Weight 106 lbs (48.1 kg)
To overflow:
Water depth 15″ (381 mm)
Capacity 60 gal (227.1 L)
* Approximate measurements for comparison only.
WV HzA
Blower motor 300 120 60 10
Heated surface 65 120 60 .5
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI).
Blower motor/Heated surface 120 V, 15 A, 60 Hz
Blower motor and heated surface are supplied with
separate 24″ (610 mm) grounding-type plug-in cords.
Installation Notes
Install this product according to the installation guide.
NOTICE: Relocation of the blower motor and check valve is
optional. Mount the blower motor and check valve together;
do not move one without the other. An additional access
panel is required for relocation. Provide an access panel at
the blower motor/control location.
Floor support under the bath must provide for a minimum of
49 lbs/square foot (238 kg/square meter) loading.
Locate a GFCI-protected 120 V, 15 A, grounded duplex
electrical outlet within 24″ (610 mm) of the blower motor.
No change in measurements if connected
with drain illustrated. (K-11677)
15-1/2"
(394 mm)
9"
(229 mm)
60" (1524 mm)
3" (76 mm)
Lumbar
Angle
28˚
21-14"
(540 mm)
20"
(508 mm)
1-1/2"
Bath Drain
2-1/2"
1" (25 mm)
(64 mm)
Product Diagram
BANCROFT®5’ BUBBLEMASSAGETM BATH WITH BASKTM HEATED SURFACE
Page2of2
1201685-4-
B
1-1/4" (32 mm)
1/2" (13 mm) R.
Integral Flange Detail
32" (813 mm)
1-1/4"
(32 mm)
Loading...