Page 1
ARCHERTM
Features
Acrylic
•
Blower motor with 300 W heater, and electronic user
•
control
Blower motor is supplied with a grounding-type
•
plug-in cord
120 BubbleMassage
•
Drop-in
•
Low threshold height
•
Slotted overflow for maximum bathing depth
•
Integral lumbar support
•
Armrests
•
72″ (1829 mm) x 36″ (914 mm) x 19″ (483 mm)
•
TM airjets
Codes/Standards Applicable
Specified model meets or exceeds the following:
ADA
•
ICC/ANSI A117.1
•
CSA B45.5/IAPMO Z124
•
IAPMO IGC 171
•
ASTM E162
•
ASTM E662
•
UL 1795
•
Specified Model
6’ (1.8 m) BUBBLEMASSAGETM BATH
K-1124-G
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
0: White
•
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1124-G 6’ (1.8 m) BubbleMassage bath – drop-in only ❑ 0 ❑ Other_____
Required Accessories
K-7271 Clearflo slotted overflow brass bath drain OR ❑ CP ❑ Other_____
K-7272 Clearflo slotted overflow bath drain – PVC pipe ❑ CP ❑ Other_____
Recommended Accessories
K-1446 Remote blower installation kit NA
Optional Accessories
K-9529 Removable bath seat ❑ 0
Product Specification
The acrylic bath with airjets shall be 72″ (1829 mm) in length, 36″ (914 mm) in width, and 19″ (483 mm) in height. Bath shall
have a blower motor with 300 W heater and an electronic user control. The blower motor shall have a grounding-type plug-in
cord. Bath shall have 120 BubbleMassage airjets. Bath shall have slotted overflow for maximum bathing depth and low
threshold height. Bath shall have an integral lumbar support and armrests. The bath with airjets shall be Kohler Model
K-1124-G-_______.
Page 1 of 2
1071368-4-
E
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
ARCHERTM
Technical Information
Fixture*:
Bathing well
Basin area, bottom 51-3/8″ (1305 mm) x 21″ (533 mm)
Basin area, top 64-1/2″ (1638 mm) x 30-1/2″
Weight 100 lbs (45.4 kg)
To overflow
Water depth 15″ (381 mm)
Capacity 72 gal (273 L)
* Approximate measurements for comparison only.
Drop-in cutout 70-1/2″ (1791 mm) x 34-1/2″ (876 mm)
Blower
motor:
(775 mm)
Heater V Hz A
300 W 120 60 5
Required Electrical Service
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI):
Blower motor: 120 V, 15 A, 60 Hz
Blower motor is supplied with a 24″ (610 mm)
grounding-type plug-in cord.
Installation Notes
Install this product according to the installation guide.
NOTICE: Relocation of the blower motor and check valve is
optional. Only mount the blower motor and check valve
together. Do not move one without the other.
NOTICE: Two access panels are required for blower motor
and check valve relocation. Provide one access panel at the
blow motor/control location and another at the control box.
Floor support under this product must provide for a minimum
of 41 lbs/square foot (197 kg/square meter) loading.
The hot water supply should be 70% of the capacity of the
bath or greater. Installations will vary.
Not suited for a three-wall alcove with an overhead shower.
Will comply with ADA when installed per Section 607
Bathtubs of the Act.
No change in measurements if connected
with drain illustrated. (K-7272)
18"
(457 mm)
1-1/4"
(32 mm)
2-1/2"
(64 mm)
1-1/2"
Bath Drain
11-1/4"
(286 mm)
72" (1829 mm)
4-1/8"
(105 mm)
1-1/2"
(38 mm)
Drop-In
Rim Detail
Required Blower Motor Access
20" (508 mm) W x 15" (381 mm) H
36" (914 mm)
19"
(483 mm)
3/4" (19 mm)
Product Diagram
ARCHERTM 6’ (1.8 m) BUBBLEMASSAGETM BATH
Page2of2
1071368-4-
E
Loading...