Page 1
DEVONSHIRE
®
Features
Acrylic
•
120 BubbleMassage
•
Drop-in
•
Textured bottom surface
•
UL listed
•
Blower motor with 300 W heater and electronic user
•
control
60″ (1524 mm) x 32″ (813 mm) x 20″ (508 mm)
•
TM airjets
Codes/Standards Applicable
Specified model meets or exceeds the following:
UL 1795
•
ASTM E162
•
ASTM E662
•
CSA B45.5/IAPMO Z124
•
ASME A112.19.7
•
Specified Model
5’ BUBBLEMASSAGETM BATH
K-1357-G
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
NA: None applicable
•
Other: Refer to Price Book for additional colors/finishes
•
Model Description Colors/Finishes
K-1357-G 5’ Bubblemassage bath ❑ 0 ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain ❑ CP ❑ PB ❑ Other_____
Optional Accessories
K-1446 Remote blower installation kit ❑ NA
Product Specification
The acrylic drop-in Bubblemassage bath shall be 60″ (1524 mm) in length, 32″ (813 mm) in width, and 20″ (508 mm) in height.
Bath shall have a blower motor with 300 W heater and an electronic user control. Bath shall feature a textured bottom surface
and 120 Bubblemassage airjets. Bath shall be UL listed. Bubblemassage bath shall be Kohler Model K-1357-G-____.
Page 1 of 2
1034591-4-
F
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
DEVONSHIRE
®
Technical Information
Required Electrical Service
Fixture*:
Basin area:
Bathing well 42″ (1067 mm) x 20″ (508 mm)
Top area 51″ (1295 mm) x 24″ (610 mm)
Weight 84 lbs (38.1 kg)
To overflow:
Water depth 14″ (356 mm)
Capacity 60 gal (227.1 L)
* Approximate measurements for comparison only.
Drop-in cut-out 58″ (1473 mm) x 30″ (762 mm)
Blower
motor:
Heater V Hz A
300 W 120 60 5
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI):
Blower motor: 120 V, 15 A, 60 Hz
Blower motor is supplied with a 24″ (610 mm)
grounding-type plug-in cord.
Installation Notes
NOTICE: If the blower motor and check valve are
relocated, the following two procedures are required: 1.
Provide two access panels. Locate one access panel at the
blower motor/control location and the other access panel at
the control box. 2. Relocate the blower motor and the check
valve together. Do not relocate one without the other.
Install this product according to the installation guide.
Floor support under the bath must provide for a minimum of
47 lbs/square foot (230 kg/square meter) loading.
A blower motor access panel is required.
No change in measurements with drain
shown. (K-7161-AF or K-7161M-AF)
16"
(406 mm)
2-1/4"
(57 mm)
3"
(76 mm)
1-1/2" OD
9"
(229 mm)
60" (1524 mm)
2-1/2"
(64 mm)
1" (25 mm)
Product Diagram
Blower Motor Access
18" (457 mm) W x
15" (381 mm) H
20"
(508 mm)
18-1/2"
(470 mm)
32" (813 mm)
DEVONSHIRE®5’ BUBBLEMASSAGETM BATH
Page2of2
1034591-4-
F
Loading...