Page 1
PORTRAIT
®
Features
Acrylic
•
6 Flexjets
•
Ten color-matched sequencing Bodyssage
•
Two pulsating neckjets with pillow
•
240 V, 20 A electrical service
•
Drilled for required grab bars
•
Color-matched jet trim included
•
Coordinating Portrait
•
Variable speed pump with 1.5 kW heater, back-lit
•
user keypad, and remote control
67″ (1702 mm) x 42″ (1067 mm) x 22″ (559 mm)
•
TM
TM backjets
Suite
®
Codes/Standards Applicable
Specified model meets or exceeds the following:
CSA B45.5/IAPMO Z124
•
ASME A112.19.7
•
CSA B45.10
•
CSA C22.2 No 218.2
•
UL 1795
•
ASTM E162
•
ASTM E662
•
Specified Model
5.5’ MASSAGE EXPERIENCE BATH
WHIRLPOOL
K-1457-LM
ALSO K-1457-RM
Colors/Finishes
0: White
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
PB: Vibrant®Polished Brass
•
Model Description Colors/Finishes
K-1457-LM 5.5 Massage Experience bath whirlpool – pump at left (shown) ❑ 0 ❑ Other_____
K-1457-RM 5.5 Massage Experience bath whirlpool – pump at right ❑ 0 ❑ Other_____
Required Accessories
K-9653 Grab bars – pair ❑ CP ❑ PB ❑ Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain ❑ CP ❑ PB ❑ Other_____
K-T15880/K-15708 Coralais
K-T15881/K-15708 Coralais base faucet (requires handle kit) OR ❑ CP ❑ PB ❑ Other_____
K-T16122/K-300-K Revival
base faucet (requires handle kit) OR ❑ CP ❑ PB ❑ Other_____
®
faucet ❑ CP ❑ PB ❑ Other_____
®
Product Specification
The acrylic bath whirlpool shall be 67″ (1702 mm) in length, 42″ (1067 mm) in width, and 22″ (559 mm) in height. Bath whirlpool
shall have 6 Flexjets. Product shall feature a variable speed pump, 1.5 kW heater, back-lit user keypad, and remote control.
Product shall have ten color-matched sequencing Bodyssage backjets, and two pulsating neckjets with pillow. Product shall be
drilled for required grab bars. Bath whirlpool shall have 240 V, 20 A electrical service. Product shall be UL listed. Bath whirlpool
shall coordinate with Portrait Suite. Bath whirlpool shall be Kohler Model K-1457-____-____.
Page 1 of 2
1023231-4-
F
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
Page 2
PORTRAIT
®
Technical Information
Required Electrical Service
Fixture*:
Bathing well:
Basin area, bottom 40 ″ (1016 mm) x 27″ (686 mm)
Basin area, top 61″ (1549 mm) x 32″ (813 mm)
Weight 150 lbs (68 kg)
To overflow:
Water depth 16″ (406 mm)
Capacity 90 gal (341 L)
* Approximate measurements for comparison only.
Included component:
Cut-out template 113311-7
Pump Heater V Hz A
1.5 kW 240 50/60 15
Minimum access panel (required):
Pump/control 34″ (864 mm) W x 15″ (381 mm) H
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI) or Residual
Current Device (RCD):
Pump/control 220-240 V, 20 A, 50/60 Hz
Installation Notes
Install this product according to the installation guide.
Maximum deck thickness should not exceed 2″ (51 mm).
Floor support under whirlpool must provide for a minimum of
48 lbs/square foot (232 kg/square meter) loading.
Hot water supply should be 70% of capacity or greater.
Installations will vary.
If installing a rim-mount faucet, make sure there is no
interference with drain overflow and circulating system before
drilling any holes. Consult local and national codes for
minimum air gap requirements if installing a spout on the
faucet deck.
5-1/2"
(140 mm) Max
Pump/Piping Protrudes
Beyond Rim
No change in measurements if connected with
drain illustrated. (K-7161-AF or K-7161M-AF)
Recommended Faucet Area
Pump/Control Access
34" (864 mm) W x
15" (381 mm) H Min
3" (76 mm) x 24" (610 mm)
Flat Faucet Deck
42" (1067 mm)
2"
(51 mm)
1-1/2" OD
Product Diagram
2-3/4" (70 mm)
Max
33-1/2"
(851 mm)
67" (1702 mm)
3" (76 mm)
13-1/2"
(343 mm)
6-1/2"
(165 mm)
3-1/2" (89 mm)
22"
(559 mm)
2-7/8" (73 mm)
PORTRAIT®5.5’ MASSAGE EXPERIENCE BATH WHIRLPOOL
Page2of2
1023231-4-
F
Loading...